Question about 1995 Nissan Altima

2 Answers

Go i hav to sperate the bell housung from the ransaxle to gt at the input shaft seal? does it sit in the backside of the bell housing?

Posted by on

2 Answers

You have to remove the entire transaxle from the vehicle.

Then you have to pull the trans pump, to change the seal

Posted on Nov 05, 2010

Testimonial: "i have never used a sight like this and thanks for a quick response. Sorry for my typing errors."

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

To change the axel seal you have to pull the axel. you shouldn't ever have to remove the bell housing at all. input shaft seal A.K.A. axel seal. check you gear oil or trans fluid allso when you are done. it might be low.

Posted on Nov 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Hyundai Accent , leaking tranny fluid from bell housing, I pulled the tranny, replaced the main input seal, chucked it back together, and it's still leaking like a mother------


there is a seal on thr shaft and one in the torque coionverter that runs in the hiusing for that shaft
and you don't chuck it back together or you will be doing it again and again and again

May 23, 2017 | Hyundai Cars & Trucks

1 Answer

My 1987 Nissan se v-6 truck is leaking oil really bad is it the rear main seal


where is it leaking from
in front of the b ell housing--- sump gasket
out of the bell housing drain hole --could be rear main seal or gear box input shaft seal
from down the side of the motor in front of the bell housing--- rocker cover gaskets
is the sump over full

Sep 16, 2015 | Nissan Cars & Trucks

1 Answer

Transmission fluid leak


check the cooling lines for leaks (loose fittings). If it is from the bell housing area it will be front seal in torque converter of manual the clutch input shaft. If from the rear it may be a drive shaft seal both boxes.

Dec 01, 2013 | 1997 Hyundai Sonata

1 Answer

Oil leakage on Mercedes Benz 5.0L engines


oil in the bell housing can be rear main seal and it can also be input shaft seal in the gear box if manual. The sump bolts on the rear main cap and will leak next to the bell housing indicating a main seal . If auto then the seal on the converter will leak and the oil will leak out of the bell housing. If you are convinced that it is a main seal then check that there is no crankcase pressure issues to make it leak. Change the engine oil and clean the area and if the oils is clean then that will indicate engine or gear box. Put a white chalk line across any oil paths and watch for it to cross the chalk and change the chalk colour.

Nov 15, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

I replaced the seal at the front pump and the torque converter but still leaking inside the bell housing any ideas


Either the input shaft seals are leaking or
A failed throwout bearing/slave cylinder could leak brake fluid into that area, and a leaking crankshaft seal would let engine oil in there.

Jun 08, 2011 | 1996 Dodge Grand Caravan

1 Answer

Change throwout bearing 2002 ford mustang gt 4.6 litte


The throw out bearing slides on a collar behind the input shaft on the front of the transmission inside the bell housing.
It will require removal of the drive shaft, shifter handle, transmission, & clutch cable to gain access to it.
Recomend having this done by a professional.

May 10, 2011 | 2002 Ford Mustang

1 Answer

I have a leak coming from inside the bell housing of my transaxle leaking onto my clutch making it slip new clutch replaced less than a week ago and rear main seal replaced oil smells like gear oil (rotten...


There is an oil seal on the gearbox/transaxle input shaft. If this has failed it will leak oil on to the clutch.It might be able to be replaced by just removing the gearbox again to access the seal. Most likely though is, the gearbox will need to be opened up to replace it.

Oct 12, 2010 | 1998 Suzuki Swift

1 Answer

Is the bell housing bolt pattern on a 1980 Ford escort the same as a cortina gearbox?


Yes, the splines are bigger on the 1.6 and up gearboxes on both the input and output shafts

May 30, 2009 | 1983 Ford Escort Gt

1 Answer

Problem to start the engine


make sure that the Crank shaft position sensor which sits on the bell housing has not become damaged.

Apr 24, 2009 | 1998 Isuzu Trooper

Not finding what you are looking for?
1995 Nissan Altima Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...