Question about 1992 Mercury Sable

1 Answer

What bolt(s) have to be removed in order to remove the battery. Thanks 1992 Mercury Sable

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

There should only be maybe battery hold down and the terminal post bolts.

Posted on Nov 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 1992 Mercury Grand Marquis starter have 2 or 3 bolts?


normally a three bolt...but better to remove the original, as you will probably need to return a core anyways in most cases.

Mar 19, 2014 | 1992 Mercury Grand Marquis

1 Answer

How to remove starter for mercury sable


first remove the negative battery cable then locate the starter it will be on the side of the engine by the trans then you will need a 13mm and or a 15mm socket to remove the starter bolts and a wrench to remove the wires then put it back in the same way you took it out last thing you do is hook the negitive cable back up

Jan 12, 2013 | 1998 Mercury Sable

1 Answer

1998 mercury sable.need to change vss,does this have to be done from underneath vehicle'am a little afraid of breaking exhaust bolts


Vehicle Speed Sensor (VSS) Removal
  1. Raise and suitably support vehicle.
  1. Remove dual converter Y-pipe from exhaust system. -
  2. Remove heat shield from transaxle.
  1. Disconnect vehicle speed sensor (VSS) electrical connector.
  1. Remove VSS retaining bolt and remove VSS from transaxle.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten VSS retaining bolt to 5-8 Nm (45-70 lb-in).


    ad0002a.gif

Mar 22, 2011 | 1998 Mercury Sable

2 Answers

Can't get at top bolt of 1992 Mercury Sable starter to remove it.


3/8th drive socket set with extra extensions and a universal

Dec 26, 2010 | 1992 Mercury Sable

1 Answer

I need to know where the starter is located on a 1999 Mercury Sable. I'm told I can "bang" on it with a hammer to get it to start long enough to drive it to a mechanic. New battery last...


The starter location is as follows:--- The starter is an electrical motor that provides a jolt of energy to ignite sparks needed to crank an engine.
  • First unplug the negative cable of your car battery for safety reasons.
  • Then remove the 10 bolts underneath the front of the vehicle to remove the splash guard. There are five bolts in the front, three in the center and two on each side.
  • Remove the electrical connectors attached to the starter motor. They are connected by tabs and can be easily removed with your hands.
  • You can use the socket wrench to remove the bolts to loosen starter motor. The starter motor will slip right off as the screws are removed.
This will help.Thanks.Helpmech.


Nov 12, 2010 | 1999 Mercury Sable

3 Answers

Alternator replacement what do I need to do? mercury sable 1996 Duratec moto (s) 3.o


Disconnect the positive battery cable from the battery. Unplug the plug to the alternator. Remove the nut holding the other wire to the alternator. Remove the belt, make sure to record the belt routing. Remove the alternator mounting bolts.

Apr 24, 2010 | 1996 Mercury Sable

1 Answer

1992 3.0L Mercury Sable cylinder numbers and firing order


For the 1992 Mercury Sable 3.0L V6:

Firing Order:
1-4-2-5-3-6

Cylinders:
...........(back)...........
|...1.........2.........3...|
...............................
|....4........5.........6...|
...........(front)

Distributor:
......(back)
........(+)-screw
....3........6
5...............1
....2........4
........(+)-screw
......(front)

Let me know if this helped, or if you have additiional information or questions. Feel Free to contact me at FixYa.com!

Nov 17, 2009 | 1992 Mercury Sable

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

1 Answer

How to take off alternatoron a side motor on a 2000 Mercury Sab


disconnect the battery first...and then the wiring harness and remove the two or three bolts.  It's pretty easy.

Mar 22, 2009 | 2000 Mercury Sable

1 Answer

2003 Mercury Sable headlight bulb replacement


This problem is now resolved, thanks to a prior post by sableowner.

http://www.fixya.com/cars/t1479995-2001_merc_sable_headlight_replacement

The 2003 Sable has the same headlight assembly and removal/replacement instructions as the 2001 Sable. Once I had this information in hand, bulb replacement was easy.

Jan 10, 2009 | 2003 Mercury Sable

Not finding what you are looking for?
1992 Mercury Sable Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...