Question about 1996 GMC Jimmy

1 Answer

How do I remove the door panel on my 1995 GMC Jimmy? I removed all the screws but the one by the handle.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 613 Answers

The outer panel of the inner door can be removed by lifting up the panel. The windows have a seal with clips. Make sure you do it in reverse the same way.

Posted on Nov 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to take off door panel of a 1996 GMC Yukon

  1. Remove the window handle by depressing the door panel and removing the retaining clip.
  2. Remove the door lock knob.
  3. Remove the armrest.
  4. Snap off the trim covers and remove the screws retaining the assist strap, if so equipped.
  5. Remove the 4 screws securing the lower edge of trim panel.
  6. Remove the screw at the door handle cover plate and the screw located under the arm rest pad.
  7. Remove the trim panel by carefully prying out at the trim retainers located around the perimeter of the panel.

Jun 13, 2015 | 1996 GMC Yukon

1 Answer

How do I open the hatchback from inside(or outside) in my 2000 GMC Jimmy if its broken and won't open from the outside?

you will need to remove inside door panel and find rod from handle to latch and pull it and push door

Feb 21, 2015 | 2000 GMC Jimmy

1 Answer

How do you replace drivers side mirror on 1997 GMC Jimmy?

you need to remove the inner door will have to look for the screws holding the panel on at the arm rest area and behind the door handle.were the door lock lever is you will have to remove the plastic cover.then if you have power windows its easier as you don`t have to remove window handle,if its manual windows then there is a clip that must be removed to remove the handle,its located between the handle and the door panel and usually faces the handle knob,push the clip off of the handle.then you will have to go around the edge of the panel along the side and bottom and pull outward to disconnect the push in clips from the door.then move the panel to remove it from the door(may have to disconnect wire connectors).then in the upper right area of the inner door panel the bolts will be visible,make sure window is up.remove bolts and electrical wires if power mirrors and remove the mirror.install in reverse order.

Apr 29, 2011 | GMC Jimmy Cars & Trucks

1 Answer

How to change brake light switch in 95 gmc jimmy

Remove lower drivers side access panel 7mm head screws (3), Remove switch retaining clip on pedal arm and slide switch off to unplug harness, Install in reverse order.

Mar 24, 2010 | 1995 GMC Jimmy

1 Answer

Cant remove door pannel on driver side 04 gmc seirra

1. Remove the door handle bezel.

2. Insert a flat-bladed tool between the door handle bezel and the trim panel in order to release the handle bezel tab retainers.

3. Remove the door trim panel upper extension.

4. Release the upper extension by pulling outward on the front edge in order to release the upper retainer clips.

5. Remove the upper extension from the trim panel by lifting up and out.

6. Using a suitable flat bladed tool, gently pry the manual lock lever from the door trim panel. Remove the trim panel screw.
*Remove the screw (2) from within the opening where the manual door lock lever resides.
*Remove the screw (3) from the opening in front of the armrest.
*Remove the screw located beneath the map pocket, if equipped.

7. Carefully slide the trim panel up in order to release the retainers from the door. Disconnect the electrical connectors.

Note: the top part of the door panel is not separate from the bottom. The "upper extension" is just the small triangle piece directly behind the mirror on the interior.

Simplified instructions
Remove the bezel around the door handle.
Pry out the manual lock.
Remove the 3 or 4 screws depending on options
Slide the door panel up off of the engagement tabs.

Good luck and thank you for using Fixya.

Mar 16, 2010 | 2004 GMC Sierra 2500

1 Answer

How do i remove my door panel on my 2005 jimmy,

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.

Sep 23, 2009 | GMC Jimmy Cars & Trucks

1 Answer

Drivers Side Door Handle

You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

Jul 10, 2009 | 1989 GMC S-15 Jimmy

2 Answers

How do I remove interior front door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then just remove the bolts for the mirror

May 16, 2009 | 1997 GMC Jimmy

1 Answer

Door panel removal 1995 GMC Jimmy

There are two screws under a cover at the bottom of your inside door handle and on your door latch. Other then that snap all the fasteners free from the door before you pull the panel, oh and have some silicon to re attach the plastic vapor to the door. Good luck

Mar 21, 2009 | 1995 GMC Jimmy

1 Answer

How do you remove the door panels on a 1995 mercury villager

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Jan 04, 2009 | 1995 Mercury Villager

Not finding what you are looking for?
1996 GMC Jimmy Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides