Question about 1995 Pontiac Grand Am

1 Answer

Will the quad 4 transmission bolt up and work on the 3.1L V6? The car has a blown up quad 4 in it now, and i would rather have a V6 in it rather than a used quad 4. i have a V6 motor, wiring harness and computer out of a 95 chevy monte carlo. it is all the same as a V6 grand am, but idk if the transmission will bolt up. i havent ripped it apart yet, because i don't know if i wanna keep it.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 835 Answers

No, you will have to use monte carlo engine -trans-wire harnnes-computer -

Posted on Nov 05, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


Automatic Transmission Application Guide ' Performance ...
Automatic Transmission Application Guide .... Buick, SKYLARK, 1995-1996, L42.3L/2.4L V6 3.1L, 4T60E ..... Honda, ACCORD, 1998-2002, V6 3.0L, B7XA.

Does a CL tranny fit Accord V6? - Honda-Tech
Jan 8, 2009 - I hope its just a bolt on thing like B and D tranny. Any help would be great. .... The 2.3l four banger from the accord or cl will fit the v6 j30 engine. Is that rite? ... Do not buy a '97 to '99 3.0CL transmission and expect it to work in yourAccord. It will bolt up to the .... Honda 1998-1999 Accord - (3.0L V6) - B7XA

Dec 08, 2015 | Honda Cars & Trucks

1 Answer

I just purchased a 1964 1\2 mustang 200cu(v6), but the problem is my shift linkage is missing some bolts. I need the size of the bolts! Anybody?

Manual Transmission three speed shifter bolts to extension housing they take either 5/16 X 18 and 3/4 to 1 inches long or 3/8 X 16 3/4 to 1 inches long

Nov 09, 2013 | Cars & Trucks

1 Answer

Need to know if a 305 will bolt up to a v6 transmission in a omega 3.8 v6

i have 79 monza, 3.8 litre, v6, 4 speed standard...i want to replace it with 305...will it bolt to the transmission??

Aug 05, 2012 | Cars & Trucks

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive

If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

1 Answer

Can i tighten the torque converter bolts on my 07, 5.9 cummins, with out dropping my transmission

There is a dust cover that comes off to allow access to these bolts, look in area between the engine and trans. for a cover about 1/4 the size of the bell housing.

Dec 27, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

Upgrade 1996 Chevy 4.3L V6 to 5.7L Vortec V8 electric conversion

Different computer for sure, and probably a bunch of sensors, distributor, wires , starter, plug - ins, etc. The only way I would ever attempt that is if i had a whole perts truck to pick off of. You'd be far better off to fix the head gasket, sell it, and buy a truck with a V8 in it already, than to try that.

Aug 19, 2009 | 1996 GMC Sierra

1 Answer

I have a 1998 4 litre v6 that i want to put in a 1995 3.8 litre v6 mustang, will the transmission bolt pattern line up?

No, the transmission will not bolt up. Also the engine will sit too far forward because the holes are different in the k-member.

Jul 05, 2009 | 1995 Ford Mustang

1 Answer

Bought the wrong 700r4?!

I believe the bolt pattern is the same that transmission should bolt up to your v-8 assuming it's a small block, the transmission should work fine, you may need to modify the shifter but everything else should be compatible, if your v-8 is carberated make sure you have the correct throttle link set up because correct tv cable adjustment is critical, the v-6 transmission may have a lighter stack up in the 3-4 drum so dont be to hard on it while in 3rd or 4th.

good luck

Jun 14, 2009 | 1984 Chevrolet Camaro

1 Answer

Remove manual V6 Magna trans from motor

undo all the bolts connecting transmission to tail shaft, then do the same with all the bolts connecting transmission to motor take out transmission.

Mar 05, 2009 | 1998 Mitsubishi 3000GT

2 Answers

Will the six cylinder auto work behind the V8? We are talking ED.

yes a transmission should bolt up to the v8 as long as it's stays a small block and not a big block , i'm sure the tranny bolt pattern will bolt on a small block or a v6 /but the v6 transmission wont last long on a v8 :) gl on your project..

Jan 06, 2009 | Ford Fairmont Cars & Trucks

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

82285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides