Question about 2005 Chevrolet Impala

Open Question

Where is the blend door actuator located on driver side on a 2005 chev impala and instrutions for replacement thanks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

oldfishead
  • 155 Answers

SOURCE: new blend door actuator doesnt operate

had this problem before... recheck part#....is it for EATC or MANUAL...??? eatc on a manual will only go to half way...sounds like they gave you the wrong part....its a pain to replace wasn't it.....hope this helped you...GL

Posted on Jul 06, 2009

warlock61
  • 659 Answers

SOURCE: need to locate blend door actuator 98 lincoln

it is located on top of the heater box assy behind the dash just to the left of of the glovebox if you open the glovebox and look to the left you can see it

Posted on Jul 11, 2009

  • 491 Answers

SOURCE: 2005 Chevy Impala driver's side heat blows cold.

First....buy a drivers side air flow actuator at a auto parts place for dual zone heating/cooling.
(NAPA etc will have it.....or the dealer)
Open the glove compartment.....all the way....you may have to take the screws out at the bottom......look in at the heater assembly....look over to the left....you will see the two air flow actuators.
Look at the part you have and match it to the part on the heater assembly.
The actuator that is closest to the engine is the drivers side control.
Replace it.
Try your controls and check for heat and cooling on both sides.
The stepper motor in these actuators goes bad on quite a few...but over look that.....you have a great car,good for many miles of trouble free driving.


Posted on Nov 03, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 impala door actuators located drivers side and passenger?


Door Lock actuator ? Inside the door , have to take inside panel off ! There are videos on youtube showing how to replace the actuator on most make , model an year vehicles .

Oct 12, 2016 | 2005 Chevrolet Impala

1 Answer

Where is the location on a 2005 Chev. Silverado blend door actuator


usually in the middle of the dash way back where you have to remove dash to get to it .

Feb 21, 2015 | 2005 Chevrolet Silverado

2 Answers

How do I change the door blend actuator on my 2003 impala


most door lock actuators are located within the driver door and each of individual doors. Its a small motor about $5.

Feb 17, 2015 | Cars & Trucks

1 Answer

Why does it blow hot air thru drivers side and cold thru passengers side


You have a problem with either the blend door actuator of the door itself.

Jul 09, 2014 | 2008 Chevrolet Impala

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

1 Answer

Afternnon, just wondering about the best way to locate the blend doors in the hvac box without ripping out the dash on my 2000 jeep grand cherokee. Thanks in advance. Duane


y9ou can gain access to the driver side blend door actuator by removing the glove box. The actuator will be in the left corner of the glove box opening. If you remove the actuator you will be able to turn the pin. If you can turn it 360 degrees the blend door is broke.

If your lucky its only the drivers side. If you get the repair kit from chrysler it will come with instructions with pictures on how to replace the blend door without pulling the HVAC unit/Dash. If the passenger side is broken the HVAC unit will need to be removed.

Heater treater (google them) also have a metal blend door replacement and instructions online on how to replace them without pulling the HVAC housing.

Nov 28, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Drivers side blend door actuator not working properly. replaced actuator, when plugged in before installing actuator runs constantly. Is the problem in the control board or in the dash?


Hello: I have bad news for you, if you run the actuator without it connected to the door the actuator is ruined, it will have to be replaced. After replacement the system has to have the doors (actuators re-calibrated.) re-calibrated. This is done with a Tech 2, A GM special tool.

Nov 12, 2010 | 2005 Chevrolet Impala

1 Answer

Ac blowing hot air


the blend door actuator located on the air box (right hand side under dash) is prob. inop. worst case senerio the blend door its self is broken. I have replaced the actuator more than anything.

Sep 16, 2009 | 2005 Chevrolet Silverado

2 Answers

Hacv controle


It is the actuator part there are a couple of them have to lye on back to get to up by the gas pedal tight fit area had to replace them myself to.

Sep 03, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
2005 Chevrolet Impala Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...