Question about 2001 Lexus RX 300

1 Answer

My iginition switched is locked and won't turn.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 1,420 Answers

Hello this the way to get a hold of me,Lee

Posted on Nov 05, 2010

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Volvo started fine went to store went to start nothing happened. key would not turn completely in iginition


Sometimes the steering wheel locking mechanism or the shifter location may cause the switch not to turn all the way.
try the transmission in neutral and then try to start.

Feb 15, 2015 | 2006 Volvo V70

1 Answer

By pass passlock on 97 chevy blazer


Check this site out!

http://newrockies.com/

Dec 14, 2014 | 1997 Chevrolet Blazer

1 Answer

Iginition switch turn on but iginition relay not


If you had said what car we could help, so I'll just tell you to find the in car fuse box and under hood fuse box from the owners manual and see where the relay is.

Oct 20, 2014 | Cars & Trucks

1 Answer

Turn on iginition switch and no engine check light


Check the engine fuse, if the car starts the bulb could be blown.

Oct 20, 2014 | Cars & Trucks

1 Answer

How to replace iginition switch


To replace the ignition switch remove the horn pad be careful the wire is still attached to the turn signal switch the plastic piece push down and turn it comes out then remove snap ring on the end off the steering wheel then nut place a dot of finger nail polish on the shaft and wheel for alignment purposes use a steering wheel puller once off then install a lock plate puller compress down and remove lock ring once removed (lock plate) this is spline d to go on one way then take the cancel cam off (slides off) remove turn signal lever screw and turn signal screws lift up to gain access to the ignition switch retaining bolt a small piece of plastic is covering the screw that is the key buzzer switch it just pulls out be careful not to drop the spring steel retainer down the column it does not come out that easy and does not install that easy either. Place ignition in the on position remove and put the new one in the same way this allows the key buzzer to go in with out interference from the plastic shoe that's part of the switch. the lock plate tool can be rented from the parts store.

Apr 19, 2014 | 1987 GMC S-15 Pickup

1 Answer

How do I get the old iginition key lock out of the


There should be a button inside the column that you push in, or a bolt to remove, been awhile since I did one. You may need to have the key in the lock cylinder and turn the lock cylinder.

Apr 23, 2010 | 1982 Chevrolet El Camino

2 Answers

Bmw e36 immobilised, iginition lights come on, but the starter wont turn over. how do i start the car to get it to a garage, i dont wont to pay the £70 for recovery truck


BMW E36 immobilizer Hope the following will help. Had similar problems. The transmitter buttons on keys is for central locking and alarm. Inside the key at the front there is a small electronic/magnetic chip that looks like a block. About 8mm long, 2mm deep and 4mm wide, not connected to any pc board. This is the immobilizer. It must match the receiver that is located behind the ignition switch. If it is loose and too far away from the receiver it won?t deactivate it. If you made a spare key it will switch on electrics but won?t start the car. If you don?t have an immobilizer chip any alarm shop will be able to program a new chip or install a new pair for your keys. There is a way to disable the immobilizer but rather have it fix and protect your car. I read an article somewhere (perhaps bmw e36 blog) of people removing this immobilizer. Good luck

Jul 06, 2009 | 1997 BMW 328

1 Answer

2001 Town & Country ignition switch locked


you need to call a locksmith to come to your home. They will replace one or more of the tumblers/cylinders inside the ignition key area. The EXACT same thing happened to me. The Chrysler dealership wanted to charge me over $400 to fix the problem. My wonderful mobile locksmith knew exactly what was srong the nanosecond I mentions the make and model! $49.00 later - FIXED! good luck!

Mar 08, 2009 | 2001 Chrysler Town & Country

Not finding what you are looking for?
2001 Lexus RX 300 Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...