Question about 2006 Toyota Land Cruiser

1 Answer

Problem on abs sistem im jorge from Mozambique im a mechanic ive a got a toyota land-cruizer uzj100 my brake master cylinder had a air leak when i press brake pedal the abs light come on and brakes get worn how can i solve ?

Posted by on

  • 1 more comment 
  • lokito4u69 Sep 05, 2008

    JUST TURN ON THE LUGHT ON MY CAR IT SAID ABS

  • Anonymous Mar 19, 2014

    Brake light on vsc light on vsc track light on and abs light on warning alarm sounding off brake pedal is hard to push and abs try and abs relays r cycling back and forth

  • Anonymous Mar 28, 2014

    Every time the abs light comes on the brakes shudder and you can't press the peddle down

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

You need a brake booster as far as abs light you need to to put tester on system and find out what code it has in it before i can diag you have to seprate prolbems

Posted on Oct 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding 02 toyota sequoia


You have a helper pushing on the brake pedal when you open the bleeders? Is fluid coming out of the bleeders when you open them?

typically you will start at the right rear, then left rear, then right front, then left front. or work your way from the farthest bleeder to the nearest bleeder to the master cylinder. Make sure the reservoir does not go dry or you will have to start over.

It is possible that when you pushed the pedal to the floor the seals in the master when through some debris and where ruined.

Apr 11, 2013 | 2002 Toyota Sequoia

1 Answer

BRAKE PEDAL GETS HARD WHILE BREAKING


brake switch bad, system needs bled, rear brake circuit probably has air in fluid, fluid is no doubt contaminated, nobody addresses this maintainance problem, bleed entire brake system, replace all fluid w/ new. if fluid in the master cylinder is black, seals are bad, some brake systems have a pump as part of master cylinder, these pumps run off fuses , 25amp, etc., check what system you have. is your fluid level correct ? the switch I refer to is @ proportioning valve below master cylinder @ frame, see abs brakes use this valve to prevent skidding, rear brakes must come on first, before front brakes. if valve is not in balance a hard brake pedal occurs, as with low fluid levels. does your brake light come on ? @ dash. have a brake shop bleed your system, if there's a problem they'll find it for you, let them do it, don't wast your time.

Jan 13, 2013 | 1994 Toyota Land Cruiser

1 Answer

Rear brakes stay engaged all the time .


Disassemble the rear brake and check the caliper and mechanics of the assembly. Something is sticking and in most cases it is the caliper but could be related to the ABS control module or splitter that is connected to the Master cylinder that the 4 brake lines connect to under the hood. Another possibility is the Emergency brake sticking.

Jun 26, 2011 | Land Rover Range Rover Cars & Trucks

1 Answer

2006 toyota landcruiser brake goes limp, pedal goes soft


Replace your master cylinder. It is leaking out of the back of the master cylinder and into the booster. If you unbolt the master and carefully look into the booster, chances are you will see brake fluid. Replace it, bleed the entire system, and enjoy your truck again.

May 31, 2010 | 2006 Toyota Land Cruiser

2 Answers

I have a 1993 toyota camry wagon and brake warning light comes on


brake master cylinder low? if so top up, or your abs module might be stuffed, need mroe info but im going with brake master cylinder needing top up of dot 3 brake fluid.

Dec 07, 2009 | 1993 Toyota Camry V6

1 Answer

My brakes lock after a mile or so ive just fitted a new master cylinder and been told its probably the wrong one what the differance between abs an none abs they both look the same ????//


That may be so, but your problem is that you don't have any 'free play' at the pedal and the brakes never fully release. Reduce the length, a small amount, of the rod which pushes into the master cylinder so that it returns clear of the cylinder contact and that you can lightly push on the pedal by hand and feel when the rod makes contact. The free play at the pedal is about 1 inch or ~1.5 cM.

Aug 25, 2009 | Land Rover Discovery Cars & Trucks

1 Answer

Can i swap the Brake master cylinder over without "reprogramming"


honestly sound more like the abs unit, it is the alloy box that the brake lines go into from your master cylinder, this will cause directional braking and awkward braking and DANGEROUS braking, it is more than likely the abs junction box and no the computer will not need program, just disconnect battery for 15 mins while doing the work. hope this has been helpfull

May 16, 2009 | 1999 Toyota Land Cruiser

1 Answer

Brakes for 2001 discovery series II


you can request a refund from the car manufaturer via the recall note.
write a letter to the district office, include all documentation and the recall note.

Jan 30, 2009 | 2001 Land Rover Discovery Series II

1 Answer

Toyota Land cruiser ABS Failure


What kind brake fluid you use, the best way is to get dealer O ring and use dealer's brake fluid. some brake fluid damaged the rubber.

Jul 26, 2008 | 1999 Toyota Land Cruiser

Not finding what you are looking for?
2006 Toyota Land Cruiser Logo

Related Topics:

629 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...