Question about 2006 Chevrolet Trailblazer

1 Answer

Driver door master switch replaced, still not working. All fuses are good.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 510 Answers

{: ) A new ly installed driver door switch needs to be programmed before it can work prop[erly on your vehicle.

Posted on Jun 08, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear window doesn't work

If it doesn't work with master switch or door switch, it is very common the the motor is out. When pushing either switch check for any type of noise In. The door. If there is no noise and it doesn't sound like it is binding up the replace the master switch on drive door. It is common that the master switch malfunction can cause system to short. Even though the door switch itself is not working, the door switch has to get its voltage from the master switch, so if the master switch is not working nether will the door switch

Mar 15, 2015 | 2008 Hyundai Santa Fe

1 Answer

Where is the fues for the windows

Lots of cars use a 20 amp circuit breaker rather than fuses for the windows. Usually located in the fuse panel inside the car.
If no windows and no switches work at all, it could be a bad master switch on the driver's door, but more likely a broken feed or ground wire in the door opening where the wires go from the door into the car.. On the master switch you should have one hot wire (feed wire) there, with the key on. This will verify that either the fuse or circuit breaker is good, and power is supplied to the master switch. There will also be a ground wire (probably black) from the master switch going back to a ground just inside the car, possibly at the kick panel on driver's side, grounded to the body sheet metal.
Good luck.

May 16, 2012 | Saturn Vue Cars & Trucks

1 Answer

All windows except the driver's side are not working.

First, if the driver's window is working, there is no need to waste your time looking for fuses. ALL of the windows are powered by the SAME fuse.

The first thing I recommend checking is the window "lock" switch on the master switch. If it is in the "lock" position, none of the other windows will work (it is designed to do that)

Other than that, you need to check for power and ground at all of the other door switches. The BLUE/BLACK wire at each of the switches should have battery voltage anytime the ignition switch is in the ON position. If they do not, the wire is broken between the splice near the driver's door and the right front door. Both the RED and the GREEN wires at each switch should have continuity to ground anytime the master switch is at rest with the "lock" switch in the unlock position (the lock switch breaks these grounds to "lock" the windows and prevent them from being operated).

Jan 31, 2012 | 1991 Mitsubishi Montero

1 Answer

1990 Corolla. None of Power windows operate from master switch at driver's door, or from local switches at each door itself. Cannot find fuse labeled for power windows (ie PW). All fuses read good

Hello. Welcome to FixYa.

The most common cause of this issue is a bad master switch on the driver side door. Another common cause is a broken power wire that powers up the master switch. CHeck the wries on the connector of the master switch with a 12 vlt DC testlight, with the key on. If you have power, the wire is good, and the switch is probably bad.

Oct 03, 2011 | 1990 Toyota Corolla

1 Answer

Back glass stopped working an the lock also stopped working also

First check for fuse, and any fuse associating to the promblem. Secondly is it just one door, window, or both door, window in the back? If it is just one, then your power switch properly need replacement, if it is both and you have checked all fuse and it is good, then your master power switch is bad, (the one in the driver side)

Jan 30, 2011 | 2003 Toyota Corolla

1 Answer

Driver side door, electric windows and lock will not work.

If windows still work from other door switches, then fuse is good, if not check fuse, if they do replace master window switch, shorted out with the water.

Jul 22, 2010 | 2007 GMC Envoy Denali

2 Answers

91 4runner power window fuse s are good but none of the door windows work and only the passenger power door lock works

replace the power window master switch and chances are the lock actuators are bad. replace as neccessary. happy holidays

Dec 28, 2009 | 1991 Toyota 4Runner

1 Answer

The driver side window controls wont work but the door lock does and the windows work on the other 3 door. checked fuse box then replaced unit, still nothing

what unit if its the master switch replace the window motor. if your calling the window motor the unit replace the master switch

Oct 10, 2009 | Toyota Camry Cars & Trucks

1 Answer

Power door locks; unlock but not lock.

replace switch. if problem on all doors replace master on driver side door. switch has two modes: lock & unlock. Unlock is working, lock is not working, means power is good, individual switches are good, master switch is bad. Replace from used car fine.

Apr 23, 2009 | 1997 Ford Explorer AWD

2 Answers

Sliding power doors will not open

Just had the same problem with my '05 van. I put the Master Switch in the off position. I pulled fuse #7 on the driver side sub panel, located just above the engine hood release. I then disconnected the neg. terminal on the battery. I manually opened the pass. side slider and closed it.

I reconnected the battery and replaced fuse #7. I put the master door switch in the on position. I activated the auto door switch, and it worked.

Jan 15, 2009 | 2007 Honda Odyssey

Not finding what you are looking for?
2006 Chevrolet Trailblazer Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

83850 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides