Question about 1999 Chrysler 300M

1 Answer

Can you explain how to replace a cam shaft censor on my 300m 99

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 1,420 Answers

Welcome to FIxYa.com


The camshaft position sensor is installed in the timing belt housing cover above the left camshaft sprocket.

Removal:

1. Disconnect the negative battery cable.

2. Remove the upper intake plenum.

3. Disconnect electrical connector from sensor.

4. Remove camshaft position sensor bolt.

5. Pull sensor up out of the timing belt housing.



Installation:

If the removed sensor is reinstalled, remove the old spacer from the sensor face, Attach a

new spacer to the face of the sensor.



If installing a new sensor be sure that the paper spacer is attached to the face.

1. Install sensor in the timing belt housing and push down until contact is made with the camshaft sprocket. While holding down in position, install and tighten bolt to 12 N.m(105in.lbs) torque.

Hook up electrical connector.

Connect Negative battery back up.

can you explain how to - leedavidian_13.png


Regards, Lee Davidian


Thank you for using FixYa.com

Posted on Nov 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Nissan Altima crank shaft censor located bank 2


there is only one crankshaft sensor so you will be looking for a CAM shaft sensor for it to be on bank 2
go google and type in --location of cam shaft sensors on nissan altima engine ---

Dec 18, 2016 | Nissan Cars & Trucks

1 Answer

I have 2 engine codes on my 2005 dodge neon. they are p0325 and p0340. the car has problem starting and misses badly for a while. What is the problem and how do i fix it? thanx for the help!


the p0325 code pertains to a knock censor. the p0340 is for your cam shaft sensor. i've had this problem before. try replacing the cam shaft censor first and run the codes again to see if the other still comes up. it should fix the problem. hope this helps

Jun 24, 2014 | 2005 Dodge Neon SXT

1 Answer

Chrysler 300m stalling


be checking emissions controls for vacuum leaks..

Jan 06, 2014 | Chrysler Cars & Trucks

1 Answer

Where can I find plenum torque specs for 2004 chrysler 300m 3.5L? Replacing cam shaft position sensor


Depending on Your vehicle engine model, Vin #'s K, M, with a 3.5 ltr engine, the torque spec are 109 in lbs.

If the engine Vin # is a V, then the torque 113 in lbs

Jun 13, 2011 | 2004 Chrysler 300M

2 Answers

1999 chrysler 300m shaft cam sensor is bad.


did you check the ASD relay,located under the hood in the fuse and relay box. hope this can help.

May 14, 2010 | 1999 Chrysler 300M

1 Answer

Cam shaft censor


shud always get 2 or 3 scans for more opinionsor ask parts place guys for tips--never just replace parts in a hurry--inspec auto for loose vacuum hoses-wires...Is the batt cables tite at the post--not every solution comes on computer--get haynes manual at discount place-its a pros book

Apr 22, 2010 | 2004 Chrysler 300M

1 Answer

SHUTS OFF IN DRIVE...


Hi theoriginalj, have the CPS (cam positioning sensor) and the CSS (crankshaft sensor) checked as soon as possible either one of these has caused a lot of problems for the 300M good luck and hope this helps you. let me know how you make out in the event it may be another problem take care

Nov 12, 2008 | 2002 Chrysler 300M

1 Answer

Cranks but wont turn over


you know. i took it to a mechanic and actually.... The timing belt cut the Crank Shaft Censor... So it was the crank shaft censor again. The wires were routed wrong from the first mechanic that "fixed" the car.

Aug 01, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
1999 Chrysler 300M Logo

681 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...