Question about 1999 Chevrolet Silverado 1500

Open Question

How do you calibrate the compass on a 99 Silverado 1500. The compass currently reads a "c"?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
honeymokey
  • 3113 Answers

SOURCE: Speedo Calibration

With a GM tech 2 . Something a dealer has.

Posted on May 23, 2009

Ad
  • 634 Answers

SOURCE: 2003 Chevy Silverado Interior rear veiw mirror compass and temp

sounds like a fuse blew if both went out check fuses first

Posted on Aug 18, 2009

nitromontess
  • 4 Answers

SOURCE: 99 chevy silverado 1500 running lights.....

pull the relay out from the fuse box under the hood
drl relay. done

Posted on Jan 18, 2010

  • 1608 Answers

SOURCE: calibrating compass

Yes you can.What you have to do is press the mode button on the driver info center(DIC).Press and hold the set button for 3 seconds.The DIC will display the zone.This is what part of the country you live in.What state your in.I don`t know what Zone your in so I don`t know if it is in the correct zone or not.They go from i-15.This will determine how accurate your compass will be.If you press set it will change the zones.If it is the correct zone then press the mode set button til the DIC displays calibrate compass.Press set and the DIC will tell you to drive in circles.Find a large empty parking lot to do this.I just crank the steering wheel and keep going in circles.The DIC will say calibrating.When the compass shows direction and temperature it is done calibrating and you can stop driving in circles.Hope this helps.Good luck.If you need to know what Zone your in Just post back with the state you live in and I can tell you the zone.

Posted on Mar 29, 2010

  • 5 Answers

SOURCE: How do I reset the anti theft module in my 99 silverado 1500

leave the key in the on position for 10 minutes, then take it out and do it again for a total of 3 times..... occasionally it only takes once for 10 minutes but it shouldnt take any more than 3 times.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2007 checy impala read "calibration complete" what does that mean ????


CALIBRATION COMPLETE
Refer to Electronic Compass Calibration do you have an owners manual ?
Compass Calibration
The compass direction will show CAL if it needs to be calibrated. Before calibrating the compass, drive the vehicle to an area that is magnetically clean (free of large metallic objects).
  1. Turn ON the ignition.
  2. Before calibrating the compass, make sure the compass is set to the variance zone in which the vehicle is travelling. See Compass Magnetic Variation Adjustment below.
  3. Press the vehicle information button until the PRESS TO CALIBRATE COMPASS screen is displayed.
  4. Press the set/reset button to start the compass calibration.
  5. The DIC will display CALIBRATING: DRIVE IN CIRCLES. Drive the vehicle in circles at less than 8 km/h (5 mph) to complete the calibration. The DIC will display CALIBRATION COMPLETE when the calibration is complete.

Oct 02, 2016 | 2007 Chevrolet Impala

1 Answer

What is calibrate compass on 2004 Buick Rendezvous


Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode. 2. Press and hold the SET button for longer than three seconds. ZONE # PRESS & HOLD SET TO CHANGE: This display mode will be displayed when you are manually calibrating the system. The current zone number for compass variance will be displayed in place of the # symbol. Use the SET button to select the zone number from the graphic shown to select the current area of the country that you are driving in. PRESS SET TO CALIBRATE COMPASS: After selecting your zone, press the MODE button and this will be displayed on the DIC. Press the SET button and complete three 360 degree turns in an area free from large metal objects. The following two messages will toggle in the display until you calibrate the compass: • DRIVE VEHICLE IN CIRCLE • CALIBRATING COMPASS When calibration is complete, the display will return to its normal mode. 3-61 info obtained from MANUAL OWL
press the helpful button and follow me on fixya for more tips

Compass Variance Zone Procedure DIC Compass Driver Information Center DIC...

http://www.manuals365.com/swf/buick/2004_buick_rendezvous_owners.html?page=200

http://repair.chiltondiy.com/Buick/Rendezvous/Repair-Manual-Online
http://www.repairservicemanuals.com/Buick

Feb 02, 2016 | Buick Cars & Trucks

1 Answer

What is calibrate compass on 2004 Buick Rendezvous Vous


Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode. 2. Press and hold the SET button for longer than three seconds. ZONE # PRESS & HOLD SET TO CHANGE: This display mode will be displayed when you are manually calibrating the system. The current zone number for compass variance will be displayed in place of the # symbol. Use the SET button to select the zone number from the graphic shown to select the current area of the country that you are driving in. PRESS SET TO CALIBRATE COMPASS: After selecting your zone, press the MODE button and this will be displayed on the DIC. Press the SET button and complete three 360 degree turns in an area free from large metal objects. The following two messages will toggle in the display until you calibrate the compass: • DRIVE VEHICLE IN CIRCLE • CALIBRATING COMPASS When calibration is complete, the display will return to its normal mode. 3-61 info obtained from MANUAL OWL
press the helpful button and follow me on fixya for more tips

Compass Variance Zone Procedure DIC Compass Driver Information Center DIC...
http://www.manuals365.com/swf/buick/2004_buick_rendezvous_owners.html?page=200
http://repair.chiltondiy.com/Buick/Rendezvous/Repair-Manual-Online
http://www.repairservicemanuals.com/Buick

Feb 02, 2016 | Buick Cars & Trucks

1 Answer

How do I find the fuse on an impala 2002 for the.outside temperature and compass


There are two fuses one in the right I/P junction block an one in the left I/P junction block ! The right is marked DK / RKE 10amp fuse. The left is marked A/C / CRUSE 10amp fuse ! I don't think these are the problem ! These fuses supply power to the microprocessor in the driver information center . According to my service information the microprocessor supply's power to the ambient air temperature sensor an to the compass.
This mode displays an 8 point compass heading on the left hand side of the DIC. The compass will display the current vehicle direction relative to one of 8 compass headings using N, NE, E, SE, S, SW, W, and NW for the readout. The ambient temperature displays on the right hand side of the DIC. If the ambient temperature is below 3?°C (37?°F), the temperature reading will toggle between displaying the outside temperature and the word ICE for two minutes. If the temperature is less than minus 40?°F for more than 2 seconds, OC will display. If the temperature is above 140?°F for more than 2 seconds, SC will be displayed. If OC or SC is displayed DTC's will be set. For compass calibration and compass magnetic variation adjustment refer to Electronic Compass Calibration .

Feb 28, 2015 | 2002 Chevrolet Impala

2 Answers

2006 Expedition overhead compass reads "N" when heading "E". Wonder how to reset it so it indicates the direction accurately.


Yes. Wish I could tell you which button for sure, but to reprogram the Compass you hold one of the buttons and drive in a circle one or two times to reacquire your position.

Apr 08, 2013 | 2006 Ford Expedition XLT

1 Answer

Have 99 chevy silverado 1500 I have a headlight problem all the other lights work but headlights won't turn on


-Check "headLight fuse"
-Check connector at the headlight.
-Check the bulb. (It could burn out)

Mai

Apr 03, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

I have 2002 Yukpn Denali XL. There is a OC code that appears in the rear view. What is the cause of this and how can I fix it?


The "OC" indicates your compass is "Out of Calibration". Below is the proceedure to recalibrate your compass.

Compass Calibration
The compass may need calibration if:
 After five seconds, the display does not show a
compass heading (N for North, for example), there
may be a strong magnetic field interfering with the
compass. Such interference may be caused by a
magnetic antenna mount, magnetic note pad holder
or a similar magnetic item.
 The compass does not display the correct heading
and the compass zone variance is set correctly.
In order to calibrate, the letters CAL must be displayed
in the mirror compass windows. If CAL is not
displayed, push in the COMP button for approximately
eight seconds or until the letters CAL are displayed.
The compass can be calibrated in one of two ways:
 Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display reads a direction, or
 drive the vehicle on your everyday routine and after
several turns the compass will become calibrated and
will display a direction.

Good luck.

Oct 23, 2009 | 2003 GMC Yukon XL

1 Answer

2003 Chevy Silverado Interior rear veiw mirror compass and temp


sounds like a fuse blew if both went out check fuses first

Aug 16, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Speedo Calibration


With a GM tech 2 . Something a dealer has.

May 23, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Compass out of whack


You need to recalibrate the compass. The procedure is in your owners manual. Here are the basic steps.

First, you will need to verify that your compass zone is set to your current geographic location. Since I do not know where you are located, I cannot tell you the code. They are listed in the manual. (For example, So Cal is zone 5.)

Second, here is the compass calibration adjustment procedure:

Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
1. Start the vehicle.
2. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window.
3. Drive the vehicle slowly (less than 3 mph) in circles until CAL indicator turns off. As many as 5 complete circles may be required.
4. The compass is now calibrated.

Dec 19, 2008 | 2005 Ford F-150

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...