Question about 2004 Infiniti I35

2 Answers

Replacing all season blower motor

I have to replace a all season blower motor that is located under the glove compartment. The make of the car is an Infiniti I35. I difficult is it to remove the glove compartment?

Posted by on

  • 4 more comments 
  • angelobitt Jun 17, 2008

    the blower motor makes a motor boat kind of noise

  • chocolickboy Jun 28, 2008

    I have an 02 I 35 blower motor making very loud noise.Can it be fixed or should I just replace?

  • E300STRING Nov 30, 2008


  • Anonymous Jan 03, 2009

    I have a similar problem. My fan motor makes a squealing noise when running. It primarily occurs when it is cold out. Does this mean I need to replace the blower motor or can I do some simple maintenance to resolve this?

  • Anonymous Mar 18, 2009

    The motor is rather expensive especially considering the problem started when the car was only 4 years old. I took apart the dash and the screws holding the motor, but I could figure out how to release the wire connection.

  • Anonymous Mar 29, 2014

    replace radio 2002 infiniti i35



2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Six screws hold the glove box two at bottom four at the inside when u open the box after the screws are out pull on the box to remove and three hold the blower motor.its not hard at all.

Posted on Jun 22, 2008

  • jenwsrv Jul 12, 2011

    I had the same problem and they replaced the blower motor. Problem fixed. Now I have a squealing noise from it seems one of the tires while driving and I need to know what that is???


  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I checked the fuse box under the hood and there is no power to the relay. Check fuse box in trunk, found blown 30amp big square fuse damaged. replaced it and everything works. However, I didn't see any damaged wires under glove box, no idea how the fuse got damaged. I hope my findings help someone else.

Posted on Jun 03, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to replace blower motor on 2003 mazda protege?

the blower motor is located under the dashboard on the passenger side. you will need to remove the glove compartment to have easy access to it

Aug 25, 2014 | 2003 Mazda Protege

2 Answers

I have power to the blower motor switch but no power to the blower motor

In most cases the blower motor brushes are worn down and in some vehicle can be replace.

Oct 22, 2013 | 1998 Ford Explorer

1 Answer

How do I replace the blower motor on a 89 olds 98

Generally the blower motor is located under the glove compartment. If this is the case you have to take the unscrew the nuts that connects to the blower assembly. Once you have done this. Remove the old blower and replace with the new one.

Nov 27, 2010 | Oldsmobile Regency Cars & Trucks

1 Answer

How to replace blower motor resistor

The blower motor resistor is located behind the glove compartment adjacent to the blower motor.There is a access door under the dash right below the glove box, There are few screws that you will have to remove to take the door out. The blower motor resistor, is to the left of the blower motor in the air conditioning case.The blower motor resistor is held by screws,remove the screws to take the resistor out. Keep updated with any further queries.Thanks.

Oct 12, 2010 | 1998 Chrysler Town & Country

1 Answer

My 98 intrigue a/c and heater blower stopped blowing

This could be caused by a fuse being blown or the blower motor itself could be faulty. I would start by checking all your fuses which can be located under you drivers side dash and under the hood of your vehicle. If this does not rectify the problem you will need to replace or have the blower motor replaced. It's located under your passenger side dash usually behind the glove compartment in a plastic housing that must be removed before you can gain access to the blower motor itself.

Aug 15, 2010 | 1998 Oldsmobile Intrigue

1 Answer

Blower motor location

Hi, I had to replace mine also. It's located under the glove compartment, passenger side. Pull off the chrome moulding around the glove box and undo the screws. This will allow you access to the blower motor cover. Be careful of the light inside the glove box. You have to ubdo it's screw and feed it through the back. Undo the cover to expose the blower motor. You can also replace the interior filter in the same area if you haven't done so yet. Two screws on a narrow cover.
Good luck.

Jan 05, 2010 | 2004 Porsche Cayenne

1 Answer

The heater blower in my 2002 sentra is only woking when on the highest you know what the problem could be?

The blower resistors have gone bad and needs to be replaced.

The 2002 Nissan Sentra blower motor resistor is located near the blower motor itself, which can be found under the dashboard, on the passenger side of the car.

To access it, you have to remove the glove compartment and the isolation panel that covers the bottom of the blower. Do the following steps:

  1. first, locate and open the glove compartment on the passenger side;
  2. remove the four upper screws and slide the door lock bracket out;
  3. pull out the two pins at the inner bottom corners of the compartment;
  4. take out the glove compartment assembly;
  5. remove the two screws retaining the isolation panel and slide the later out.
Looking under the dashboard, you can now see the blower motor and, on its left side, near the firewall, the resistor block brown connector.

To take out the blower motor resistor:
  1. remove the white plastic bracket that faces it;
  2. unplug the brown connector;
  3. remove the two screws on the resistor's socket;
  4. pull the resistor block out.
The resistor block is actually a PCB ("Printed Circuit Board"). The traces printed on this board have different electrical resistance, and are used by the control assembly to vary the speed of the blower fan.

I believe Auto Zone or Parts Source has the blower resistor you need. Good luck

Nov 03, 2009 | 2002 Nissan Sentra

2 Answers

Blower motor only works on high speed only.what do i need to look for to fix this problem

your chrysler will need what is called a blower motor resistor this is located on blower motor air box under glove compartment next to your blower motor it will have a plug of wires coming out of it double check your wire at the plug if sighns of wires overheating replace the wiring and plug.

Sep 19, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
2004 Infiniti I35 Logo

1,042 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides