Question about 1992 Suzuki Swift

1 Answer

Valve Rocker arm settings

1590cc G16

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 138 Answers

Go to www.teamswift.netYou will find all the info you need.

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ticking noise while in drive getting worse, been told that noise coming from bell housing?


Valve Adjustment

Print
The 4.2L and 5.3L engines do not require a periodic valve lash adjustment.
The 4.3L engines are equipped with screw-in rocker arm studs with positive stop shoulders. Because the shoulders that allow the rocker arms to be tightened into proper position, no adjustments are necessary or possible. If a valvetrain problem is suspected, check that the rocker arm nuts are tightened to 18 ft. lbs. (24 Nm). When valve lash falls out of specification (valve tap is heard), replace the rocker arm, pushrod and hydraulic lifter on the offending cylinder.

Oct 23, 2014 | 2003 Chevrolet TrailBlazer

1 Answer

Torque settings for rocker shaft for a 1998 7k toyota 1800


There is no such thing as a rocker shaft. There is a cam shaft, rocker arm assembly, Rocker arm, lifter etc. If you are talking about the rocker arm assembly that bolts to the head, it is 58 Ft/lbs. If you are talking about the actual rocker arms, you tighten them till they contact the push rod and the valve stem and then you put oil control clips on so the oil does not spray and you start the engine. You tighten them down till the chattering noise goes away, then back them off 1/8 to 1/4 turn.

Apr 25, 2014 | 1995 Toyota Corolla

1 Answer

What is the gap setting for the rocker arm valve for 2003 Chevy impala


rocker arm bolts torqe down to 17 ft lbs with torqe wrench there is no gap setting they should just torqe down to this and be fine.

Mar 31, 2013 | 2003 Chevrolet Impala

1 Answer

Installed new oil pump and now have broken rocker arms


THe rocker arms are broken because there was not enough downward movement in the valves to allow the cam to complete its turn. IT happens when the valve spring retainer either hits the top of the valve guide or the valve springs are fully compressed forming a solid block . If you have hydraulic valve adjusters I would be suspicious of a lack of movement (seized) in the ones that broke the rocker arms

Feb 20, 2013 | Ford F-150 Cars & Trucks

1 Answer

P 2647"A" Rocker Arm Actuator


Your going to need a air pressure regulator or better yet if the ECM found fault price it and replace it
  1. Start the engine, and let it run for 5 minutes, then turn the ignition switch to LOCK (0).
  2. Remove the cylinder head cover.
  3. Set the No. 1 piston at top dead center (TDC).
  4. Move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A should move independently of the secondary rocker arm B.
    1. If the intake secondary rocker arm A moves freely, go to step 5.
    2. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, then check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
    3. Repeat step 4 on the remaining intake secondary rocker arms with each piston at TDC. When all the secondary rocker arms pass the test, go to step 6.
    4. Check that the air pressure on the shop air compressor gauge indicates over 400 kPa (4.0 kgf/cm2, 57 psi).
    5. Inspect the valve clearance.
    6. Install a 10 x 1.0 mm adapter to the inspection hole, then connect the air pressure regulator
  5. With the specified air pressure applied, move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A and secondary rocker arm B should move together. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, and check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
  6. cansmo_32.gif
cansmo_33.gif

Aug 23, 2011 | Honda Accord Cars & Trucks

1 Answer

How do I adjust the valves on a 1998 old bravada 4.3 vortec


You don't. They are non-adjustable hydraulic lifters. GM's spec for torque on the rocker arm nuts: Tighten the valve rocker arm ball studs to 47 N·m (35 lb ft). Once the valve rocker arm nuts are installed and properly torqued, no additional valve lash adjustment is required.

Aug 05, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

What is the torq setting for the rocker arms on a 91 crown vic with a 5.0L


zjlimited_1679.jpg

Fig. 2: Rocker arm assembly - 5.0L and 5.8L engines

* Apply engine oil or assembly lubricant to the valve stem tip and pushrod end. Also apply lubricant to the rocker arm and fulcrum seat contact surfaces.
* Rotate the crankshaft until the lifter is on the camshaft base circle (all the way down) and install the rocker, fulcrum seat and fulcrum bolt. Tighten the bolts to 18-25 ft. lbs. (24-34 Nm).
*
Install the rocker arm cover(s).

Hope this helps.

Aug 03, 2011 | 1991 Ford LTD Crown Victoria

1 Answer

What are the torque specifications for a 3.5l v6 1995 ford tarus rocker arm


For each valve, rotate the crankshaft until the valve lifter rests on the heel (base circle) of the camshaft lobe. Position the rocker arm(s) over the push rods, then install the rocker arm seats. Tighten the rocker arm seat retaining bolts to 44 inch lbs. (5 Nm).

Final-tighten the rocker arm retaining bolt(s) to 19-25 ft. lbs. (25-35 Nm). For final tightening, the camshaft may be in any position.

Hope helps.

May 19, 2011 | 1995 Ford Taurus

1 Answer

I replaced the lifters in my 2000 galant 2.4 L and i need to know what to torque the rocker arm shafts to.


1.5 and 1.8 engines:
* Install the rocker arm and shaft assemblies. Tighten the rocker arm shaft retainer bolts to 23 ft. lbs. (32 Nm).

* Check valve adjustment and install the valve cover. Tighten the valve cover bolts to 16 inch lbs. (1.8 Nm) for the 1.5L engine or to 29 inch lbs. (3.3 Nm) for the 1.8L engine.



2.0 engine
* Lubricate the rocker shaft with clean engine oil and install the rockers and springs in their proper places.

* Install the rocker shaft assemblies on the engine. Tighten the bolts gradually and evenly to 21-25 ft. lbs. (29-35 Nm).



2.4 engine

fa2bc50.jpg

Fig. Rocker arm shafts and components-2.4L engine



* Fit the rocker shaft springs from above and position them so that they are at right angles to the plug side. Install the rocker springs before installing the exhaust side rocker shaft and rocker arm assembly.

* Install the exhaust side rocker shaft assembly in the engine. Tighten the rocker shaft mounting bolts gradually and evenly to 23 ft. lbs. (32 Nm).
* Remove the lash adjuster retaining tools.
* Install the rocker cover and tighten the mounting bolts to 30 inch lbs. (3 Nm).

* Reinstall the spark plug wires to the spark plugs.



Hope helps.

Sep 06, 2010 | Mitsubishi Galant Cars & Trucks

2 Answers

Rocker arm come out on jeep chrysler 3.7 eng


A rocker arm is the arm that sits on top of the valve stem and connects to the push rods 'the push rods sit on the cam so when engine is running, the push rods go up and down in a timed sequence and with the rocker arms, open and close the inlet and exhaust valves. the rocker arm is located inside the valve(rocker)cover .If the rocker arm gets loose or comes out.
Check the nuts on the shaft which holds the rocker arms.either the shaft or nuts are got loose.They need to be tightened.Don't make it too tight or too loose.  Too tight,and they don't flutter right. Too loose,and they allow the rocker arms to wiggle out of whack. Other possibility can be  something is broken, bent, collapsed, or out of adjustment. 
Thanks. you can rate this solution and show your appreciation.



May 20, 2010 | 2002 Jeep Liberty

Not finding what you are looking for?
1992 Suzuki Swift Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...