Question about 1986 Chevrolet Astro Cargo

Open Question

4.3l 1986 CHEV HEAD TOURQUE SPECS - 1986 Chevrolet Astro Cargo

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: head tourque specs

The Haynes manual says for 96 - 98 to torque the head bolts to 22 ft lbs and than the short bolts 45 degrees, medium 55 and long 65 degrees

Those bolts are "Torque To Yield" bolts. You should be using new head bolts, tighten them to the spec listed and then rotate them the additional degrees of rotation that is specified. This assures that the bolts are tightened to a maximum clamp load.

To start out with, be sure to torque from the center out and there is a designated sequence to go in

e24997f.gif

Posted on Aug 25, 2008

Ad
  • 916 Answers

SOURCE: tightening head

New Headbolts are recommended

Long bolts are torqued to 46'lbs + 90 degrees.

Short bolts are torqued 43'lbs + 90 degrees.

Start in the center, and work to the edges, torquing the bolts in two stages.

Rockers are torqued to 22'lbs.

Posted on Dec 21, 2008

  • 6982 Answers

SOURCE: tourque specs for 1968 camaro

Do you mean the tightness of the ball joint nuts? If you do use 55lbs, then tighten further if cotter pin hole does not line up. DON'T back off to get pin to go in!

Posted on Apr 18, 2009

Wolfman304
  • 720 Answers

SOURCE: 4g67 head tourqe settings

Hi,

Just to add to previous solution...

Assuming your head is straight & without defects, ensure you follow the correct tightening sequence diagram (see numbers) below:


Front of engine

i e
n 10 8 x
t h
a 4 6 a
k u
e 2 1 s
t
5 3
s s
i 7 9 i
d d
e e


1) Apply a small amount of engine oil to the thread section of the bolt and install so the chamfer of the washer faces upward.

2) In the proper tightening sequence (as shown above), torque bolts initially to 22 ft.lbs. (30Nm)

3) In the proper tightening sequence, now torque bolts to 45 ft.lbs. (61Nm)

4) In the proper tightening sequence, finally torque bolts to 68 ft.lbs. (92Nm)


Now you can Install the Camshaft sprocket and tighten it to 65 ft.lbs. (90Nm), while holding sprocket in place using the correct wrench.

Confirm proper timing mark alignment.

Cheers,

Posted on Aug 17, 2009

  • 94 Answers

SOURCE: replacing cylinder head on 1986 montero with 2.6

ok
42011354

  1. Torque all bolts except No. 11 to 69 ft. lbs. on a cold engine or 75 ft. lbs. on a hot engine.
  2. Torque cylinder head to chain case cover bolts (No. 11) to 156 inch lbs.
  3. 42011356

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tourque specs


torque the cylinder head bolts to eighteen (18) foot pounds (ft/lbs) in the sequence shown in the attached photo.
27b117e1-d4c4-4596-8a8a-f275444e8ed9.jpg

Dec 07, 2013 | 1995 Isuzu Pickup

1 Answer

I need torque specs for head bolts on my 2000 chev venture. Head warped due to excessive overheating.


hope you dont plan on the same head unless its planed out..autozone has torque specs..

Jan 30, 2013 | Cars & Trucks

1 Answer

What is the torque spec for a 1989 chevrolet 454 intake bolts.


Hello there
the tourque specs are as follows
. Intake manifold bolts (cast iron head) 25 - 30 ft.-lbs. ...

Mar 12, 2011 | Chevrolet C3500 Cars & Trucks

1 Answer

Tourque specs


what engine 1,6 zetec

Mar 24, 2010 | 2004 Ford Focus

1 Answer

I need to kow the torque specs for the head bolts on a 1986 pontiac fiero 2.5l TBI


Hello! Here are a couple of images that will give you the torque specs - as well as the very important torque sequence.

6d0687b.gif
303eda4.gif



Hope this helps, and thanks for using FixYa!

Sep 29, 2009 | 1986 Pontiac Fiero

2 Answers

Replacing cylinder head on 1986 montero with 2.6 timing chain. just need timing marks and head torque specs.


ok
42011354
  1. Torque all bolts except No. 11 to 69 ft. lbs. on a cold engine or 75 ft. lbs. on a hot engine.
  2. Torque cylinder head to chain case cover bolts (No. 11) to 156 inch lbs.
  3. 42011356

Sep 17, 2009 | 1986 Mitsubishi Montero

1 Answer

1986 chev camaro runs but lights and radio wont work


you need to check your fuses for the radio they and the light are most of the time the same .

Dec 20, 2008 | 1986 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...