Question about 1991 Cadillac DeVille

Open Question

How to install window regulator jaw - 1991 Cadillac DeVille

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Window regulator replacement in 1988 olds cutlass calais (non-motor). How do I replace the window regualtor?


1985-1998 Oldsmobile Grand Am/Achieva/Calais/Skylark/Somerset
REMOVAL & INSTALLATION

Door Glass and (manual) Regulator

See Figure 1

Fig. 1: Common window attachment

SEE ILLUSTRATION #1 BELOW

1. Remove the door panel.
2. Remove the water deflector from the door.
Be careful not to tear the water deflector when removing it from the door.
The "water deflector" is also known as the "dew wiper"
3. Connect the power window switch/window regulator handle.
4. Lower window to full down position.

CAUTION
Use extreme caution when operating the window with the door panel removed. The window regulator can cause severe personal injury if body parts become entangled in the mechanism.
5. Remove the window run channel.
6. Move window to the half down position.
7. Remove the window retaining nuts.
8. While holding onto the window, lower the regulator to the full down position.
9. Remove the window by sliding it towards the rear and rotating the front of the window upward.

To install:
10. Position the new window in the door.
11. While holding onto window move regulator to half up position.
12. Install the nuts. Roll the window to the full up position.
13. Install the rear run channel.
14. Install the plastic water deflector. If necessary, secure with waterproof adhesive
15. Install the door trim panel.

Window Regulator

See Figures 2 and 3

Fig. 2: Location of the front door window regulator-1995 vehicle shown

SEE ILLUSTRATION #2 BELOW

Fig. 3: Exploded view of the rear door window regulator-1995 vehicle shown.

SEE ILLUSTRATION #3 BELOW

1. Remove the door panel.
2. Remove the plastic window deflector. Be careful not to tear the deflector when removing it from the door.
3. Remove the door window assembly.
4. Remove the bolts securing the regulator to the door.
5. Remove the nuts securing the upper regulator guide.
6. Using a 1/4 in. drill, drill out the regulator rivets.
7. If equipped with power windows, detach the electrical connector.
8. Remove the regulator through the large access hole in door.

To install.
9. Install the regulator to the door, and attach the electrical connector if equipped with power windows.
10. While holding the regulator to the inner door panel, insert the rivets, and secure them with a rivet tool.
11. Fasten the regulator bolts and upper guide nuts.
12. Install the door glass, and inside door plastic panel.
13. Install the inside door trim panel.
14. Install the plastic water deflector. If necessary, secure with waterproof adhesive.
15. Install the door trim panel.

Fig.1---------------------------------------------------------------------- Fig. 2

10_3_2011_6_07_07_pm.jpg10_3_2011_6_08_35_pm.jpg

Fig. 3

10_3_2011_6_09_40_pm.jpg

Oct 03, 2011 | 1988 Oldsmobile Calais

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How hard will it be to replace the window motor, driver side, of a 2002 Chevy blazer? Do I need special tools to do the job?


Motor Replacement - Power Window

Removal Procedure
Be very careful
Hope this helps




Caution: Do not attempt to service the regulator motor withoutreleasing the counterbalance spring tension. The regulator lift arm isunder tension from the counterbalance spring and can cause personalinjury if the motor is removed from the regulator.

  1. Remove the window regulator.
117423422
  1. Drill a hole through the window regulator and the sector gear.
117423423
  1. Install a bolt and a nut through the hole in order to lock the sector gear in position.
  2. Drill out the rivets that secure the power window motor to the window regulator.
  3. Remove the power window motor from the window regulator.
Installation Procedure
  1. Install the power window motor to the window regulator.
117423423

Important: Remove the nut and the bolt that were used in order to secure the sector gear in position.

  1. Install the rivets in order to secure the power window motor to the window regulator.
  2. Install the window regulator.

Jan 01, 2011 | 2002 Chevrolet Blazer

1 Answer

Electric window feel down broken mechanism


Glass & Regulator

zjlimited_228.jpg

Fig. View of inner door frame and window regulator assembly

  1. Lower the window glass and remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Raise the window enough to reach the regulator bolts, hold the glass underneath and unbolt the glass from the regulator.
  4. To remove the glass, raise the glass by hand and tilt it as necessary to remove it from the track.
  5. To remove the regulator, lower the glass carefully to the bottom of the door and remove the bolts to remove the regulator.
  6. Installation is the reverse of removal. Tighten all bolts to 61 inch. lbs. (7 Nm).
zjlimited_229.jpg

Fig. Installing the door glass regulator



Motor

  1. Remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Unbolt the window from the regulator and carefully lower it to the bottom of the door.
  4. Disconnect the wiring and remove the motor mounting bolts.
  5. Remove the 3 guide rail bolts and lower the motor and guide rail assembly out the bottom of the door.
  6. Installation is the reverse of removal.
NOTE The upper cable must be below the guide rail mounting bracket.
Showing window regulator motor, or assembly carrier with window regulator, removal/installation

zjlimited_230.jpg

Fig.

NOTE The illustration shows the removal and installation of the window regulator motor/assembly carrier with the window regulator on the rear doors. The procedure for removing and installing on the front doors is the same.
zjlimited_231.jpg

Fig. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier. Remove the screws and take off the window regulator motor

  1. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier.
  2. Remove the screws and take off the window regulator motor.
To install:
  1. The gearing will move when the window regulator motor is removed; it is then no longer centered. The gearing must be aligned when the window regulator motor is installed until the window regulator motor is centered again.
  2. Installation is the reverse of the removal (see illustration).

Motor & Regulator

NOTE The illustrations in the procedure show the replacement of the window regulator motor/carrier assembly with window regulator for rear doors. The procedure for front doors is the same.
  1. Remove the front or rear carrier assembly.
  2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
  3. Unfasten the bolts (1) and remove window regulator.

    zjlimited_232.jpg

    Fig. Unfasten the bolts (1) and remove window regulator

To install:

NOTE By removing window regulator motor, gearing shifts, it is not centered.
zjlimited_233.jpg

Fig. By removing window regulator motor, gearing shifts, it is not centered

  1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
  2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
  3. Carrier assembly with window regulator, installing:
    1. For replacement part carrier assemblies, the gearing is secured in place with a cable tie.

      zjlimited_234.jpg

      Fig. For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)

    2. Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.
  4. Remove the cable tie .
  5. By removing window regulator motor, gearing shifts, it is not centered.
  6. When installing window regulator motor, gears must be aligned until window regulator motor is centered again.
  7. Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

Hope this helps to solve it.

Dec 14, 2010 | 2002 Volkswagen Jetta TDI

1 Answer

How to un ininstal the electric window motor on a 1997 lumina


Window Regulators and Motors - REMOVAL & INSTALLATION

NOTE Some window regulators are retained at least in part, by heavy-duty pull rivets. To remove these rivets, the center mandrel must be pushed through with a small punch, and the rivet(s) drilled out with a 3 / 16 inch drill bit. The factory recommended repair requires the use of the same quality of heavy-duty pull rivet.
Front
CHEVROLET


fd0e0d8.jpg
Fig. Typical W-Body power window regulator and bolt tightening sequence


293730c.jpg
Fig. Chevrolet models use a cross-arm type window regulator
Coupe and sedan front doors use a cross arm regulator. The following procedures are required for removal and replacement of both power and manual window regulators.
  1. Remove the door trim panel, as outlined in this section.
  2. Remove the plastic sheet water deflector and the energy absorber (foam pad).
  3. Remove the door window. Please see Door Window Glass, Removal and Installation in this section.
  4. Detach the electrical connector, if equipped.
  5. Remove the window regulator bolts and the regulator cam nut.
  6. Drill out and remove the pull rivets.
  7. Remove the window regulator cam bolt.
  8. Remove the window regulator from the vehicle.
CAUTION Do not attempt to service the window regulator motor separately. It is part of the window regulator. The regulator lift arm is under tension from the counterbalance spring and can cause personal injury if the motor is removed from the regulator. The door window regulator cannot be serviced separately. If defective, replace the regulator and motor as an assembly.
To install:
  1. Position the regulator by inserting the bottom through the access opening in the door, then rotate the top of the regulator through the opening while lowering the regulator to clear the top of the access opening. Align the holes in the regulator with holes in the door inner panel.
  2. Install the door window regulator bolts and tighten to 89 inch lbs. (10 Nm).
  3. Install new pull rivets. Install the upper left rivet first, followed by the lower right rivet.
  4. Install the door window regulator cam bolt and cam nut and tighten both to 89 inch lbs. (10 Nm).
  5. Attach the electrical connector, if equipped with power windows.
  6. Install the door window. Please see Door Window Glass, Removal and Installation in this section.
  7. Install the energy absorber (foam pad) and reposition the plastic sheet water deflector.
  8. Install the door trim panel, as outlined in this section.

Hope helps (remember rated this).

Jul 13, 2010 | 1997 Chevrolet Lumina

1 Answer

I need to install a window in my vw polo. It is the back seat pasanger side window, i have already purchased it and have the inside panel off. My issue is fitting the window inplace without it smashing,...


We don't have Polo in the States but it would be the same design as a Golf or even a Jetta, even a Passat.
  1. Remove nuts from glass clamping jaws, press jaws apart, an access port would reveal both nuts at the same level
  2. Lower door glass into door, pull window channel (Window rubber gasket) out of door frame and remove center connector (metal channel strip that separates vent window. A screw on top and a hex head screw at bottom)
  3. Pull door glass upward, tilt toward front and lift out of window slot
  4. Install in the reverse order of removal
Note: Clamping jaw hex nuts torque spec.......10Nm (7ft-lb)

May 04, 2010 | 1998 Volkswagen Golf

1 Answer

I need instructions on how to replace power window motor for the front driver side window of a 2002 Grand Cherokee


Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

Oct 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Power window problem. engauges then disenguages


Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
  1. Remove inside door belt weatherstrip.
  1. Remove front door window glass (21410) as described in this section.
  1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
  1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
  1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
  1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
  1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

    Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


    a9ef3ee.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

  1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
  1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

    Install four rivets to retain front door window regulator to door inner panel.
  1. Install window regulator equalizer arm bracket.
  1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
  1. Install inside door belt weatherstrip.
  1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
  1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


    Door Glass and Regulator
ac1dac5.gif

Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

Apr 13, 2009 | 1997 Ford Windstar

2 Answers

How do you remove the glass from the rear side window regulator


Remove the door panel
  1. Remove the side impact bolster.
    e0001157.jpg
  1. Detach the door speaker (if equipped).
    e0003862.jpg
  1. Disconnect the speaker electrical connector and remove the door speaker (if equipped).
    e0003863.jpg
  1. Detach the door latch release handle.
    e0001156.jpg
  1. ani_caut.gif CAUTION: Do not touch the adhesive surface as re-bonding will be impaired.
    Detach the watershield.
    • Using a suitable plastic knife (disposable cutlery), cut through the Butyl strip to enable the watershield to be peeled back.
    e0001158.jpg
  1. Remove the door glass top run retainer.
    e0001160.jpg
Vehicles with manual windows
  1. Install the window regulator handle.
Vehicles with power windows
  1. Connect the door glass operating switch electrical connector.
    e0001851.jpg
All Vehicles
  1. Align the regulator clamp with the access hole (power window shown).
    e0001853.jpg

  1. NOTE: Position the regulator operating cable to one side when drilling the retaining pin, in order to prevent damage.
    Detach the door glass from the regulator clamp.
    1. Using a suitable electric hand drill and a drill bit 8 mm, remove the retaining pin.
    1. Push out the retaining sleeve.
    1. Remove the door glass from the regulator clamp.
    • Discard the retaining sleeve.
    e0001854.jpg
  1. Support the glass, lower the glass and regulator to the lowest position.
  1. Position the lower part of the door glass top run outside the door.
    e0001161.jpg
  1. NOTE: To aid removal of the door glass, stand on the inner side of the door. Make sure the glass is removed from the inside of the door.
    Remove the window glass.
    e0001163.jpg
Installation
All vehicles
  1. ani_caut.gif CAUTION: Make sure vise jaw protectors are used.
    NOTE: Make sure that the retaining sleeve is central in the door glass.
    Attach a new retaining sleeve and retaining pin to the door glass.
    1. Position the retaining sleeve in the door glass.
    1. Using a suitable vise, press the retaining pin into the retaining sleeve.
    e54462.jpg
  1. Install the window glass in the door.
    e0004709.jpg
  1. Attach the door glass to the regulator clamp.
    • Push the door glass firmly down to engage the retaining pin and retaining sleeve into the regulator clamp.
    e54463.jpg
  1. Position the lower part of the door glass top run on the inside of the door.
    e0004707.jpg
  1. Close the window.
  1. Install the door glass top run retainer.
    e0001160.jpg
  1. Attach the watershield.
    e0004705.jpg
  1. Attach the door latch release handle.
    e0004704.jpg
  1. Connect the door speaker electrical connector (if equipped).
    e0003863.jpg
  1. Install the door speaker (if equipped).
    e0003862.jpg
  1. Install the side impact bolster.
    e0004703.jpg
Vehicles with manual windows
  1. Remove the window regulator handle.
Vehicles with power windows
  1. Disconnect the door glass operating switch electrical connector.
All vehicles
  1. Install the door trim panel

Mar 11, 2009 | 2001 Ford Focus

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

Not finding what you are looking for?
1991 Cadillac DeVille Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...