Question about 2004 Chevrolet Impala

Open Question

How do i remove the rear rotors and brakes from my 2004 chevy impala

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Hightower971
  • 183 Answers

SOURCE: Remove rear rotor 2004 Chevy Impala

Yes it should, A trick I use when this happens is to beat the lug bolts out, and the rotor will fall off. When you put it all back together use a socket and the lugnut to reseat them.

Posted on Apr 25, 2009

Ad
  • 8 Answers

SOURCE: how to change rear brake shoes on a 2004 chevy venture

The rear brake shoes use a U clip to hold the shoes together. A simple solution to this change job is to change one side at a time.
Slowly unclip the U clip from the top of the shoe and remove the left shoe and spring. Replace the left shoe and reconnect the U clip, then do the same for the other shoe. Clean, adjust,and grease the self adjuster and you're done. Do the same for the other side of the van. If you take both sides of the clip off you're in for some heavy duty stretching with pliers unless you have the right tool.

Posted on May 12, 2009

rockitman187
  • 2559 Answers

SOURCE: Removal of Rear Brake Drum on 2004 Chevy Aveo

1.Release parking brake.
2. Apply the brake pedal at least 10 times.
3. Raise and support vehicle with jack stands, etc.
4. Remove the tire and wheel assembly.
5. Remove the lock ring and the caulking nut from the spindle.
6. Remove the drum from the spindle.
Note: Pull the drum straight off the spindle.

There is an opening on the inside for adjusting the tension,It's under a rubber cap.You can use a screw driver to make the adjustment

Posted on May 13, 2009

suterman
  • 158 Answers

SOURCE: In 2004 Impala, do I have rotor or drums?

The best way to answer you question is to tell you to take the vehicle to your nearest dealer and inquire with the parts dept. I can tell you that on the ffront of your car you have rotors and the brake used on the front is called a pad. Also your vehicle does not have a separate parking brake. It is the same as the regular rear brake no matter which type of brakes you have on the back.

Posted on Jul 02, 2009

  • 295 Answers

SOURCE: Headlight wiring diagram for 2004 Chevy Impala

I would go to Alldata.com on line for your vehckle to get the wiring diagrams.

Posted on Jul 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

1 Answer

2005 Chevy impala brake pedal pulsation with brand new rotors installed


Is your ABS working properly? Under heavy braking the ABS should engage and 'pulse' the brakes on/off. It is normal to feel the brake petal flutter or pulse under your foot.

Under light braking there should be no pulsing as the ABS does not engage and you have changed the rotors and pads.

Nov 19, 2013 | 2005 Chevrolet Impala

1 Answer

Replace rear brake pads 2006 Chevy Impala


Hello, to replace the rear brake pads follow the following steps:

1. Lift the Chevy Impala with the jack and place it on jack stands.
2. Remove the wheels with a lug-nut wrench and set them aside. The lug-nut wrench can be found in the trunk of your Chevy Impala.
3. Remove the caliper with a ratchet and use a bungee cord to hang the caliper. Do not let the caliper hang from the brake hose, as the hose might break and cause fluid to leak.

4. Remove the brake caliper bracket from the steering knuckle with a ratchet. Set it aside.

5. Remove the break rotor from the hub. The rotor might require force to be removed; if it does, use a hammer to hit the rotor in the center, where the lug studs are located. Take care not to hit the studs.

6. Remove the new rotor from its packaging and use brake cleaner to remove the grease from the rotor. Grease is applied on the rotor in the factory to inhibit rust during storage.

7. Install the new rotor onto the hub.

8. Install the caliper bracket with new brake pads onto the rotor and fasten it to the steering knuckle. Use a ratchet to tighten the bolts.
9. Open the master cylinder reservoir so you don't break a seal while compressing the brake caliper.

10. Compress the brake caliper with a C-clamp, so that the caliper can fit over the new brake pads. Install the caliper by securing it to the brake caliper bracket with a ratchet.

Thanks


























Jul 19, 2010 | 2006 Chevrolet Impala

1 Answer

How do you release the anti-lock brake system to replace the rear brake rotors on a 2001 Chevy Impala?


I assume you want to take the caliper off first. Remove caliper bolts & using a pry common screwdriver pry piston on caliper back in a bit or enough to allow the caliper's removal. After this, remove rotor. I hope this helps!

Oct 03, 2009 | 2001 Chevrolet Impala

3 Answers

In 2004 Impala, do I have rotor or drums?


The best way to answer you question is to tell you to take the vehicle to your nearest dealer and inquire with the parts dept. I can tell you that on the ffront of your car you have rotors and the brake used on the front is called a pad. Also your vehicle does not have a separate parking brake. It is the same as the regular rear brake no matter which type of brakes you have on the back.

Jul 02, 2009 | 2004 Chevrolet Impala

1 Answer

2004 impala vibration when pressing brakes


hi sounds like a brake pulsation remove the brake rotors and make sure the hub face is clean of rust and the inside of the rotor reassemble the brakes and torque the wheel nuts to 100ft/lbs if it still pulsates then the rotor is warped some aftermarket rotors are warped from sitting on the shelf you can also check the laterial run out of the rotor with a dial indicator if you have one hope this helps

May 03, 2009 | 2004 Chevrolet Impala

1 Answer

Remove rear rotor 2004 Chevy Impala


Yes it should, A trick I use when this happens is to beat the lug bolts out, and the rotor will fall off. When you put it all back together use a socket and the lugnut to reseat them.

Apr 25, 2009 | 2004 Honda Accord

1 Answer

Rear disc brakes - 2000 Chev Impala - Calipers won't open enough


How did you depress the pistons? Did you use a heavy duty Air tool clamp? I'v done brake jobs in my driveway using basic cheep clamps and only manpower. Been successful. Also done total ceased you would not believe Just took Some Nasty brute force and the right tool You should be good to go.

GL

Mar 23, 2009 | 2004 Honda Accord

2 Answers

2004 Chevy Impala Brake Problem


I did a complet brake job on my 2004 Chevrolet Impala about two weeks ago, and i still have warning light on. Thw system is working great. So how do I turn off the warning Lights, Traction off light, Brake light, and in warning center Low brake fuild?

Jul 08, 2008 | 2004 Chevrolet Impala

Not finding what you are looking for?
2004 Chevrolet Impala Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...