Question about BMW 550

1 Answer

How many hours would it take to drive from Sandia Park, NM to Sun City, CA?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 67 Answers

11 hours 19 minets

Posted on Nov 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where am I suppose to vote? My address is 7824 Daniel Dr N Richland TX 76182.


We are in California but here is what is listed.
645 Grapevine Highway Hurst, TX 76054 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 B 828 West Harwood Road Hurst, TX 76054 Directions Closed · Opens 7 AM MonHours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Last day to vote early at this location is Nov 3 C 5350 Basswood Boulevard Fort Worth, TX 76137 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 100 Main Street Colleyville, TX 76034 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 6801 Glenview Drive North Richland Hills, TX 76180 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 1100 Bear Creek Parkway Keller, TX 76248 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 700 Mary Drive Hurst, TX 76053 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 2424 Forest Ridge Drive Bedford, TX 76021 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 3201 Friendly Lane Haltom City, TX 76117 Directions Closed · Opens 8 AM FriHours this week Today 8 AM-5 PM Fri 8 AM-5 PM Sat 7 AM-7 PM Sun 11 AM-4 PM Hours week of Oct 31 Mon 7 AM-7 PM Tue 7 AM-7 PM Wed 7 AM-7 PM Thu 7 AM-7 PM Fri 7 AM-7 PM Last day to vote early at this location is Nov 4 201 North Ector Drive Euless, TX 76039 Directions Closed · Opens 8 AM Fri

Oct 27, 2016 | Cars & Trucks

1 Answer

Cylinder head torque settings honda city 1.5 vtec


Cylinder head torque is done is steps, if this is not followed you will end up with another leak in a very few 1000 miles. Here is the procedure:

Step 1. Tighten all 10 bolts in sequence to 14 ft/lbs (20 Nm).

Step 2. Tighten all 10 bolts in sequence to 36 ft/lbs (49 Nm).


Step 3. Tighten all 10 bolts in sequence to 49 ft/lbs (67 Nm).

Step 4. Tighten bolts 1 and 2 to 49 ft/lbs (67 Nm) again.

Use only high quality gaskets.

Oct 20, 2011 | Cars & Trucks

2 Answers

2003 Saturn L200 (153,000 miles) 1. Gas gauge occasionally fluctuates between empty and full while driving for no apparent reason at the same time the car alarm light flashes. 2. Sitting at a light...


Wow, that's amazing....I do know the newer (third generation) 'L' have a body computer, it sounds like your's has gone loco. the security system and the horrible gas mileage also might be some major issue with the electrical system, specifically the alternator-check voltage while parked and not running (should be 12.5+), and running it should be close to 15 when started, and settle down to around 14 after a minute or 2.

Apr 02, 2011 | 2001 Saturn L-Series

1 Answer

I HAVE A 1990 LS 400 WHEN TURNING KEY NO CRANKING AND HAVE GOOD BATTERY POWER. NO POWER TO STARTER WIRE ON STARTER SELINOD.WHAT CAN IT BE


It could be a bad ignition switch or bad starter wire from the starter switch, or the PNP is not adjusted correctly:

Here are instructions on how to remove and replace the PNP, but read over it to understand how to adjust:
Park/Neutral Safety Switch REMOVAL AND INSTALLATION ES300 1993-94 Models
  1. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  2. Raise and safely support the vehicle.
  3. Disconnect the Park/Neutral switch connector.
  4. Remove the clip from the shift control cable.
  5. Remove the nut and control cable.
  6. Remove the bolts and pull out the Park/Neutral switch. To install:
  7. Install the Park/Neutral switch and loosely install the bolts.
  8. Adjust the switch and torque the bolts to 48 inch lbs. (5 Nm).
  9. Install the control shaft lever.
  10. Install the control shaft cable and torque the nut to 9 ft. lbs. (13 Nm). Fig. 1: The transaxle control shaft lever has a nut and washer to retain it - 1993-94 ES300 54617.gif
    Fig. 2: Removing the Park/Neutral switch - 1993-94 ES300 54618.gif

  11. Install the clip to the shift control cable.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Make sure the vehicle will start only in the PARK or NEUTRAL position.
1995-97 Models Fig. 3: Aligning the neutral base line and groove - 1995-97 ES300 293716.gif
Fig. 4: Park/Neutral switch removal and installation - GS300, LS400, SC300 and SC400 300569.gif
Fig. 5: Park/Neutral switch adjustment - GS300, LS400, SC300 and SC400 300571.gif
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Apply the parking brake fully and block the rear wheels.
  3. Disconnect the electrical connector from the Park/Neutral position switch.
  4. Remove the locknut and disconnect the control cable from the manual shift lever.
  5. Remove the clip from the holding the control cable to the bracket.
  6. Remove the nut, washer and the manual shift lever from the manual valve shaft.
  7. Using a flat bladed tool, bend the lock washer back away from the nut.
  8. Remove the nut and lock washer from the Park/Neutral switch.
  9. Remove the two bolts and the Park/Neutral position switch. To install:
  10. Install the Park/Neutral position switch to the manual valve shaft. Leave the two bolts loose at this time.
  11. Install the lock washer and nut. Torque the nut to 61 inch lbs. (7 Nm).
  12. Using a flat bladed tool, bend the lock washer over the nut to secure the nut in place.
  13. Adjust the Park/Neutral as follows:
    1. Install the manual shift lever to the Park/Neutral switch and set the shift lever to the neutral ( N) position.
    2. Align the groove and the neutral basic line on the Park/Neutral switch.
    3. Hold the Park/Neutral switch in this position and tighten the two bolts to 48 inch lbs. (5 Nm).
  14. Install the manual shift lever with washer and nut.
  15. Install the control cable to the manual shift lever and install the nut. Torque the nut to 11 ft. lbs. (15 Nm).
  16. Install the control cable to the bracket by installing the clip.
  17. Connect the electrical connector to the Park/Neutral switch.
  18. Lower the vehicle and check the vehicles shifting positions.
  19. Connect the negative battery cable to the battery.
  20. Verify that the vehicle only starts in PARK or NEUTRAL.
GS300, LS400, SC300 and SC400
  1. With the ignition switch OFF, disconnect the battery cables, negative terminal first. Allow 90 seconds to elapse before performing any other work.
  2. Raise and safely support the vehicle.
  3. If necessary, remove the front exhaust pipe.
  4. Disconnect the neutral start switch connector.
  5. Remove the control shaft shift lever.
  6. Pry off the washer and remove the nut.
  7. Remove the bolt and pull out the neutral start switch. To install:
  8. Install the Park/Neutral switch and loosely install the bolt.
  9. Adjust the switch as follows:
    1. Loosen the neutral start switch bolt and place the shift lever in the N position.
    2. Align the groove and the neutral basic line.
    3. Hold in position and tighten the bolt to 9 ft. lbs. (13 Nm).
  10. Install the nut and washer.
  11. Install the control shaft shift lever.
  12. Connect the electrical connector.
  13. Install the front exhaust pipe. Torque the front nuts to 46 ft. lbs. (62 Nm). Torque the pipe support bracket to bolts to 32 ft. lbs. (43 Nm). Torque the No. 2 front exhaust pipe to the front exhaust pipe bolts to 32 ft. lbs. (43 Nm).
  14. Lower the vehicle.
  15. Connect the negative battery cable to the battery.
  16. Verify that the vehicle will only start in the N or P positions.
---
Maybe try to press the brake pedal and run the gear shift throughout the full range of gears while the car is on level ground, and retry the starter to see if there is a faulty PNP adjustment.

Try to start in Neutral not Park, and jiggle the gear shift back and forth to see if the PNP is not adjusted right.

Good luck on this repair.

Nov 09, 2010 | 1992 Lexus Ls 400

1 Answer

1996 Buick Park Ave. Security light goes on and off while driving.


The factory security system (VATS/PassKey) is dying. You can find a great write-up here: http://newrockies.ca , it was the only thing that saved my Park Avenue.

Apr 06, 2010 | 1996 Buick Park Avenue

2 Answers

Drivers side sun visor hanging loose in my way all the time


2006-2007MY SONATA SUN VISOR
REPLACEMENT (SERVICE CAMPAIGN T64)
CAMPAIGN APPLIES TO VEHICLES LOCATED IN THE WESTERN,
PC, AND SOUTHERN REGIONS ONLY. THIS WOULD INCLUDE
THE STATES AL, AR, AZ, CA, CO, FL, GA, HI, KS, LA, MS, NC, NM,
NV, OK, OR, SC, TN, TX UT, AND WA.

Aug 24, 2009 | 2006 Hyundai Sonata

1 Answer

Need to add tranny fluid to '99 Rodeo, but where??


CAUTION: DO NOT OVERFILL.
Overfilling will cause foaming, loss of fluid, abnormal shifting and possible damage to the transmission.
1. Park the vehicle on level ground and apply the parking brake firmly.
2. Check fluid level with engine running at idle.
NOTE: Be sure that transmission fluid temperature is below 30degrees C (86degreesF).
3. Move the selector lever through all gear ranges.
4. Move the selector lever to “Park”.
5. Let engine idle for 3 minutes and open the overfill screw (1).
6. Add released transmission fluid until it flows out over the overfill screw opening.
7. Let engine idle until a fluid temperature between 32C (90F) and 57C (135F) is reached, then close the overfill screw (1).
Torque: 38 Nm (3.9 kg·m/28 lb ft)
NOTE: To prevent fluid leaks, the overfill screw and oil drain screws gasket must be replaced each time these screws are removed.

CAUTION: Do not open overfill screw with engine stopped.
CAUTION: DO NOT CHECK FLUID LEVEL UNDER THESE CONDITIONS:
 Immediately after driving at sustained highway speeds.
 In heavy city traffic during hot weather.
 If vehicle is towing a trailer.
If the vehicle has been operated under these conditions, shut the engine off and allow the vehicle to “cool” for thirty (30) minutes. After the cool down period, restart the vehicle and continue from step 2 above.

0c878d2.jpg

Aug 07, 2009 | 1990 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

stephen Kiarie
stephen Kiarie

Level 1 Expert

32 Answers

Fred Sops

Level 2 Expert

351 Answers

vince

Level 3 Expert

1216 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...