Question about 1999 GMC Yukon

1 Answer

What is underneath the a/c compressor on a chevrolet 5.7 motor?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

I believe the power steering pump is mounted below the A/C compressor.

Posted on Nov 04, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

3.9 V6. How can I remove the A/C clutch?

You need special tool
Tools Required ?€¢
J 37872 Compressor Clutch Holding Tool

J 6083 Snap Ring Pliers

Important: Remove the three adjustable dowels from the J37872 Compressor Clutch Holding Tool.
Install three 5/16 x 1 inch bolts in place of the dowels.
Remove and discard the compressor clutch plate bolt.
Use the J 37872 to hold the compressor clutch plate from turning.
Remove the compressor clutch plate from the compressor.
Remove the compressor pulley snap ring using the J 6083
Remove the compressor pulley from the compressor.
Remove the compressor clutch coil snap ring using the J 6083 .
Remove the compressor clutch coil from the compressor.
google J 37872 - to see tool !

Jan 31, 2016 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

Where are the camshaft intake senor on a 2012 chevy equinox


1 - Q38 Throttle Body

2 - G18 High Pressure Fuel Pump

3 - B23F Camshaft Position Sensor - Intake

4 - B37 Engine Oil Pressure Switch

5 - B68 Knock Sensor

6 - B26 Crankshaft Position Sensor

7 - M64 Starter Motor

8 - Q2 A/C Compressor Clutch

9 - G13 Generator170440314

Oct 17, 2014 | 2012 Chevrolet Equinox LS 4dr SUV 2.4L...

1 Answer

Where is the water thermostat on a 1989 chevrolet celebrity 6 cylinder

follow the upper rad hose from the rad to the motor where the hose connects to the motor is the thermostat housing and the thermostat is underneath this housing.

Sep 19, 2014 | 1989 Chevrolet Celebrity

1 Answer

Ac only blows on 5 in 03 impala

You have a bad resistor. This controls your speed of the blower motor. It is located near your blower motor on passenger side behind glove box. You might be able to access it from underneath the glove box by removing the lower panel. This is what it looks like, but you will only see the black part going into the ducts near your fan7_26_2012_4_16_09_am.jpg

Jul 26, 2012 | 2003 Chevrolet Impala

1 Answer

Motor mounts

There are a total of four mounts in the engine compartment. There is a motor mount on the passengers side of the motor underneath. There is a transmission mount on the drivers side underneath. There are two Torque-strut mounts (each sold as two pieces) between the top of the motor and the radiator shroud at the front of the engine.

Dec 18, 2011 | 2002 Chevrolet Impala

1 Answer

I have a problem with the a/c. when u turn the a/c on 1,2,3,4 the compressor did not work . Then when u turn the a/c up on 5 the blower working , my car malibu 2003

If this also does this for the may have a bad heater motor resistor. It's located behind the glove box at the heating housing area.

Aug 05, 2011 | 2003 Chevrolet Malibu

2 Answers

My blower motor on the 1980 L82 is noisy and needs to be removed. I need to know what requires to be removed and how does the blower motor come out. I can see it under the hood on the pasenger side....

These instructions come from Chilton.
1. Disconnect the battery negative first.
2. Unbolt the A/C compressor and move it out of the way but DO NOT disconnect the lines from the compressor.
3. Remove the coolant resevoir, if you have one.
4. Disconnect the wiring from the motor, and the cooling tube if there is one.
5. Remove the mounting screws from the motor and pull it out. If it sticks because it is attached with a sealer, then pry GENTLY against the case to remove the motor.
6. Installation is the reverse.
These instructions are only good for 80-82 models. Hope this helps.

Dec 22, 2010 | 1981 Chevrolet Corvette

1 Answer

How to replace fan motor on 1997 chevrolet cavalier s2

hte blower motor sits behind and under the glove box, you can get at it from underneath the dash

Nov 18, 2009 | 1997 Chevrolet Cavalier

1 Answer

The fan in my truck only turns on on high speed.

A bad blower motor resistor will cause it. It is located ny the blower motor p.s. below dash.

Sep 28, 2009 | 2000 Chevrolet Silverado

1 Answer

1996 chevrolet k1500 blower motor

Underneath the glove box there is a round housing (your foot probably hits it when you are riding shotgun). Reach up under there and disconnect the (+) and (-) wires to power the motor. Pull the housing off by hand and voila there is the blower. There are 5 or 6 screws hard to get to 1 of them. 7/32" I believe. If you need more clearance take the glovebox door off (just unsnap the 'castle gate chain' from the left of the inside of the glovebox).

Jan 10, 2009 | 1998 Chevrolet K1500

Not finding what you are looking for?
1999 GMC Yukon Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides