Question about 1994 Jeep Cherokee Country

1 Answer

How do i check the master cylinder for the clutch on a 94 jeep cherokee sport? the clutch pedal drops to the floor with no pressure. i'm trying to find out where the master cylinder is and how i can check to see if it has fluid

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 63 Answers

The resivour is the smaller circular pot next to the brake mastercylinder on the left if your looking from the front. most likely caused by a bad slave cylinder

Posted on Nov 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a honda accord coupe 94 the clutch stops workin after i start the car i ihe car doest accelerates


If you mean you step on the clutch, put transmission in gear and release clutch with no engagement (pedal returns to top position) there is a good chance your clutch disc or pressure plate, or both are worn out and need replacing.
If your clutch pedal is going to the floor and not returning there could be a leak in the system, a bad clutch master cylinder or a bad slave cylinder on the transmission. Check the fluid level in the clutch master cylinder. If it is low or empty you have a leak or component failure. Visually inspect clutch master, line, slave cylinder for fluid leaks. replace as needed. If hydraulics are o.k., suspect clutch disc/pressure plate.

May 09, 2014 | 1994 Honda Accord

2 Answers

I have a 1992 jeep cherokee 2dr 4.0 H/O 5spd. that lost most pressure in the clutch


It sounds as though the seals in the master cylinder have perished and aren't doing their job. The reservoir is full, yes .. but the fluid isn't getting pumped because of worn seals... there's no pressure developing.

If there are overhaul kits available - try one. They're much cheaper than buying a new clutch master cylinder. It isn't a difficult job.

0results for 1992 jeep cherokee clutch master cylinder repair

Mar 15, 2017 | 1992 Jeep Cherokee Sport

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

96 jeep grand cherokee bypassed abs mod, have brakes but pedal goes to floor


Do you mean it fades to the floor?
If you hit the pedal hard and they are ok ,but if you hold the pedal and let off the pressure just a little ,and the pedal falls to the floor,the master cylinder is bad. This is assuming there are no leaks.

Nov 06, 2011 | 1996 Jeep Grand Cherokee

1 Answer

I am trying to install a new clutch in my 96 jeep cherokee it is a sealed unit I have it in but it wont go into gear how do I blead it or does it need to be blead???


I would start by topping off the clutch fluid.If you have replaced clutch the fluid level will drop.There is a bleeder screw at the slave cylinder.Basically you can pump the pedal and hold it down while someone opens the bleeder.Close the bleeder when pressure is released and then release pedal and repeat procedure.Good Luck!

May 10, 2011 | 1996 Jeep Cherokee Sport

2 Answers

I have a 98 cherokee sport. clutch pedal is releasing right off the floor and some times i have no clutch at all i have replaced the clutch master twice and the slave twice, air checked the line. i have...


About the only thing that would be left to check would be that the clutch pedal free travel is correct. It should be about ¼ inch (measured at the pedal rubber) before the push rod that links the pedal arm to the piston in the master cylinder contacts the piston
If free travel is incorrect, adjust by first loosening the locknut on the rod at the end where it attaches to the pedal arm and turning the rod in either direction to obtain the correct free travel. One adjusted retighten locknut.
You appear to have eliminated all the other possibilities, so the only other reasons for your problems could be that the clutch plate is warped and and therefore not disengaging fully or the pressure plate diaphragm spring is faulty and not allowing full disengagement.

Jan 10, 2011 | 1998 Jeep Cherokee

1 Answer

My 94 jeep wrangler 4.0 when stopped with car in gear with clutch pedal pressed to floor sometimes the clutch disengages and i have changed slave cylinder and clutch resevoir is full. my version has...


may have a bad mastercylinder for slave, also did you bleed system good and no leaks,id say master may be the problem or clutch preasure plate is bad .good luck.

Oct 27, 2009 | 1996 Jeep Cherokee

3 Answers

Pedal goes all the way to floor and still in gear


YOUR CLUTCH IS NOT DISENGAGING. THERE COULD BE A PROBLEM WITH THE CLUTCH MASTER/SLAVE. CHECK FOR ACTION AT THE SLAVE. ALSO, A BROKEN PRESSURE PLATE SPRING OR THROW-OUT BEARING CAN KEEP THE CLUTCH ENGAGED ALL THE TIME.

Sep 18, 2009 | 1994 Jeep Wrangler

1 Answer

Tranny slipping while shifting


You have a bad seal in either the clutch master cylinder or the slave cylinder.

Please rate this a fixya

Feb 13, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Cherokee Country Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...