Question about 2000 Chevrolet Silverado

1 Answer

How do you remove a radiator hose off these trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 63 Answers

Make sure engine is COLD
remove both clamps on rad hose twist turn and pull until it comes off
put clamps onto new hose
some coolant will be spilled make sure to add coolant to the rad after this is done
and leave the cap off and let it idle until at operating temp to bleed air out of the system then put cap back on and bobs your uncle

Posted on Nov 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a radiator on a 2006 ford 500, need someone to show me how to take a radiator out


Drain radiator by removing lower radiator hose. REmove plastic cover panels on top of radiator. Remove upper radiator hose. Remove radiator fans. Disconnect transmission cooler lines. Remove radiator hold down bolts. Reverse to install.

Sep 25, 2017 | Ford Cars & Trucks

2 Answers

Instructions to remove radiator in 1999 isuzu Rodeo and install new one


remove items in this order and fit in reverse
1st-grill to help with access
2nd-cooling fan
3rd-fan shroud
4th-radiator hoses x3
5th-radiator
remember to remove the rubbers at the bottom of the old radiator to use on the new radiator

Dec 02, 2016 | Isuzu Cars & Trucks

1 Answer

How do I remove my radiator from my 2000 Lincolncontinental


  1. Disconnect the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove engine air cleaner.
  4. Remove the upper radiator hose from the water bypass tube.
  5. Remove the upper radiator supports.
  6. Remove the radiator overflow hose from the radiator.

26003867-whqtqzmdhjettns5tbwoqqce-3-0_0.gif
7.Remove the upper radiator hose and two clips from the fan shroud.
8. Remove the transmission fluid cooler lines from the fluid cooler inlet and outlet fittings.
9. Disconnect the engine control sensor wiring from the auxiliary electric cooling fan motor.

NOTE
Support the A/C condenser core and bracket.

10. Remove the nuts retaining A/C condenser core to the radiator.


26003867-whqtqzmdhjettns5tbwoqqce-3-1.gif
11. Raise the vehicle on a hoist.
12. Remove the radiator air deflector.


26003867-whqtqzmdhjettns5tbwoqqce-3-3.gif 13. Remove the lower radiator hose (8286) from the radiator.
14. Remove the bumper cover pin-type retainers.


26003867-whqtqzmdhjettns5tbwoqqce-3-6.gif
15 .Remove the power steering/transmission fluid cooler and position the cooler aside.
16. Support the fan shroud, radiator and the radiator support.
17. Remove the bolts and the left side radiator support.
18. Remove the bolts and the right side radiator support.
19. Lower and remove the fan shroud, radiator and the radiator support from the vehicle.
20. Remove the upper radiator hose from radiator.
21. Remove the two bolts and the fan shroud from the radiator.
22. Installation is the reverse of the removal procedure.

Dec 12, 2015 | Cars & Trucks

1 Answer

How do i remove a radiator from a 2002 jaguar typex


FIRST YOU DRAIN OUT THE COOLANT SYSTEM.DRAIN THE EXPANSION TANK REMOVE EXPANSION TANK HOSES FROM RADIATOR.REMOVE COOLING FAN MOTOR AND SHROUD.REMOVE UPPER RADIATOR HOSE, REMOVE RADIATOR LOWER COOLANT HOSE. REMOVE CONDENSOR TO RADIATOR MOUNTING BOLTS.DISCONNECT TRANSMISSION COOLER LINES FROM RADIATOR.REMOVE RADIATOR SUPPORT RELEASE CLIPS OR BOLTS MOUNTING FIXTURE. THEN REMOVE THE RADIATOR.

Jun 13, 2011 | 2002 Jaguar X-Type

1 Answer

Installing radiator


REMOVAL
1. DRAIN ENGINE COOLANT
2. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR COVER
3. DISCONNECT ECT SWITCH CONNECTOR FROM FAN SHROUD
4. DISCONNECT ELECTRIC COOLING FAN CONNECTORS
5. REMOVE RADIATOR HOSES
(a) Disconnect the upper hose from the radiator side.
(b) Disconnect the lower hose from the water inlet pipe.
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. A/T:
DISCONNECT OIL COOLER HOSES
8. REMOVE RADIATOR AND ELECTRIC COOLING FANS
(a) Remove the 2 bolts and 2 upper supports.
(b) Lift out the radiator.
(c) Remove the 2 lower radiator supports.
9. REMOVE RADIATOR LOWER HOSE
10. A/T:
REMOVE A/T OIL COOLER HOSES
11. REMOVE ECT SWITCH WIRE
12. REMOVE ELECTRIC COOLING FANS Assembly is reverse order.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/flavio_517b938f50183b92

Jan 01, 2011 | 1996 Toyota Camry

1 Answer

How to replace a radiator on a1994 toyota land cruiser


dak408_129.gif

  1. Disconnect battery ground cable.
  2. Drain engine coolant.
  3. Remove battery and tray,
  4. Remove radiator grille
  5. Disconnect No. 3 water bypass hose.
  6. Disconnect radiator inlet hose.
  7. Disconnect coolant reservoir hose.
  8. Loosen water pump pulley mounting bolts.
  9. Loosen lock, pivot and adjusting bolts of alternator and remove drive belts.
  10. Disconnect oil cooler hose from clamp on fan shroud, then remove shroud.
  11. Remove water pump pulley mounting nuts.
  12. Remove fan with fluid coupling, water pump pulley and fan shroud.
  13. Disconnect transmission oil cooler hoses.
  14. Disconnect radiator outlet hose.
  15. Remove radiator brackets, then the radiator.
  16. Reverse procedure to install.

Dec 11, 2010 | 1994 Toyota Land Cruiser

1 Answer

How do I remove my car radiator?


Section 303-03: Cooling, Engine 1997 Explorer, Mountaineer Workshop Manual REMOVAL AND INSTALLATION Radiator - 4.0L Removal
  1. NOTE: Refer to following illustrations.
    Drain the cooling system by removing the radiator cap (8100) and attaching a 9.5 mm (3/8 inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the radiator draincock (8115) and allow the coolant to flow through the hose into a suitable container.
  1. Loosen hose clamps at throttle body and engine air cleaner assembly. Remove air cleaner outlet tube and position aside.
  1. Remove radiator overflow hose from the radiator, disconnect two hose locators at top of radiator and position hose aside.
  1. Remove two fans shroud bolts. Lift the fan shroud out of the lower retaining clips and position it on the fan blade.
  1. Position upper and lower radiator hose clamps, remove hose from radiator and position it on the fan blade.
  1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator, install protective caps over lines and position aside.
  1. Remove two upper radiator bolts.
  1. Tilt the radiator back (rearward) approximately 25 mm (one inch) and lift directly upward, clear of the radiator support bracket and the fan blade.
Installation
  1. Position the radiator into engine compartments, make sure that mountings on both tanks are inserted into radiator support brackets. Install radiator retaining bolts. Tighten to 6-8 - (54-70 lb-in).
  1. Remove protective caps from cooler lines. Connect the two transmission cooling lines at the oil cooler fittings on radiator. Tighten to 16-24 - (12-17 lb-ft).
  1. Install upper radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Install lower radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Position fan shroud in lower retaining clips and install upper bolts. Torque to 6-8 - (54-70 lb-in).
  1. Position radiator overflow hose, connect to radiator and locators.
  1. Position air cleaner outlet tube to throttle body and air cleaner assembly. Tighten to 2-3 - (18-27 lb-in).
  1. Fill the cooling system; refer to Cooling System Draining, Filling and Bleeding in this section.

Oct 28, 2010 | 1997 Mercury Mountaineer

1 Answer

How to remove a radiator from a 1988 cadillac seville


1988 Cadillac Seville 4.5L TBI 8cyl Repair Guide
Radiator - REMOVAL & INSTALLATION

On the 8-250 and 8-273 engines use only a coolant solution specifically designed for use in aluminum engines.
  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Disconnect the air conditioning compressor, if so equipped, and position it out of the way without disconnecting the hoses.
  4. Remove the clamp that holds the air conditioning high pressure vapor line to the cradle.
  5. Loosen the hose clamps and disconnect the upper and lower radiator hoses.
  6. Disconnect the two transmission cooler lines and plug them.

Disconnect the heater return hose, if so equipped.
  1. Remove the two top radiator cradle clamps, straps or sheet metal cover and the fan shroud. Disconnect the reservoir hose from the filler neck.
  2. Remove the vacuum hoses, if so equipped. Mark them for proper installation.
  3. Pull the radiator straight up and out of the car.
  4. Reverse the above procedure for installation.

92c12aa.jpg


Fig. 1: Radiator fan shroud mounting - diesel sedans, gasoline-engined cars similar


ce6d621.jpg


Fig. 2: Some radiator fan shrouds mount like this


c78285a.jpg
Fig. 3: Common coolant recovery tank, mounted on the inner fender


0451576.jpg
Fig. 4: Removing the support bolt - radiator removal


5936e81.jpg
Fig. 5: Removing the support - radiator removal


3a629af.jpg
Fig. 6: Removing the radiator metal cover bolt - radiator removal


d55bb20.jpg
Fig. 7: Removing the radiator metal cover - radiator removal


167e7c8.jpg
Fig. 8: Removing the radiator overflow hose


944e13f.jpg
Fig. 9: Removing the transmission oil cooler lines - radiator removal


81eeab8.jpg
Fig. 10: Removing the radiator


9235ddf.jpg
Fig. 11: Removing the hose from the radiator fan shroud


1f4b026.jpg
Fig. 12: Removing the power steering tank bolts from the radiator fan shroud


a78590d.jpg
Fig. 13: Removing the power steering tank from the radiator fan shroud


e4e32df.jpg
Fig. 14: Removing a common radiator fan shroud


I really hope help with this (remember rated and comment this).

Mar 15, 2010 | 1988 Cadillac Seville

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...