Question about 2004 Pontiac Grand Prix

1 Answer

How do i remove power outlets?

Both stopped working not at same time by using compressor to air tires

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Check ur fuses

Posted on Jul 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to locate AC condenser bolts and brackets


59ad8a03-bab5-48dc-9e0a-1cb5643b56af.jpg
REMOVAL
A/C Compressor Mounting
1. Discharge the refrigerant. Refer to MTC-111, "HFC-134a (R-134a) Service Procedure" .
2. Remove the front right wheel and tire assembly. Refer to WT-6, "
Rotation" .
3. Remove the engine under cover and the splash shield using power tool.
4. Remove the engine air cleaner and air ducts. Refer to EM-14, "
Removal and Installation" .
5. Remove the drive belt. Refer to EM-12, "
Removal and Installation" .
6. Disconnect the compressor electrical connector.
7. Disconnect the high-pressure flexible hose and low-pressure flexible hose from the compressor.

Jun 13, 2014 | 2004 Nissan Titan

1 Answer

Air compressor works...rear suspension low...just used air compressor to fill tire a few weeks ago...could this be related? We had never used it in over 8 years...


The air suspension has absolutely nothing to do with your tire pressures. If your rear suspension is low and you can hear the compressor running all the time, it is because you have a leak in your suspension system. You need to get it diagnosed and repaired as soon as possible. If you let it continue, it will burn-up your compressor, then it will be REALY EXPENSIVE to fix.

Jul 09, 2011 | 2003 Oldsmobile Bravada

1 Answer

Radio quit working when I hooked up a portable compressor lighter


The radio uses a five amp fuse, maybe 7.5 amp. pull them and look at them you tell they are blown

Jun 17, 2010 | 1995 Chrysler Town & Country

1 Answer

Timing chain is loose how do I replace or tighten


You need to pull out the timing cover. 4-6 hours of work. Here is the step to remove the Cover, then you need to remove the Sprockets.
moz-screenshot.pngmoz-screenshot-1.png
  1. Remove the oil pan.
  2. Remove the power steering belt if so equipped.
  3. Remove the air conditioning belt, compressor and bracket if so equipped.
  4. Remove the fan clutch (fluid coupling), with the fan and water pump pulley.
  5. Matchmark and remove the crankshaft pulley(s). This bolt will be very tight. Use the counter-holding bar, properly installed, to hold the crankshaft while loosening the bolt. Use the pulley extractor or gear puller to remove the pulley from the shaft.
  6. Remove the water bypass pipe.
  7. Remove the fan belt adjusting bar. If necessary, remove the lower power steering bracket for access.
  8. Disconnect the heater water outlet pipe.
  9. Unbolt the timing chain cover assembly. Be careful to loosen only the correct bolts.

To install:
  1. Install new gaskets over the dowels on the timing chain cover. Slide the cover assembly over the dowels and pump spline. Insert the retaining bolts and tighten them. Tighten the 8mm bolts to 9 ft. lbs. (13 Nm) and the 10mm bolts to 29 ft. lbs. (39 Nm).
  2. Temporarily install the adjusting bar to the alternator. Install the adjusting bar to the chain cover and tighten the bolts to 9 ft. lbs. (13 Nm).
  3. Install the heater water outlet pipe.
  4. Install the water bypass pipe.
  5. Install the crankshaft pulley and bolt. Use the counter-holding tool to hold the pulley and tighten the bolt to 116 ft. lbs. (157 Nm). If equipped with air conditioning, install the second crankshaft pulley.
  6. Install the water pump pulley and fluid coupling with the fan.
  7. Adjust the tension on the drive belts.
  8. Install the air conditioning compressor bracket, compressor and belt if they were removed.
  9. Install the power steering belt and adjust it.
  10. Attach the oil pan.
  11. Install the radiator.

Jun 04, 2010 | 1987 Toyota Pickup

1 Answer

1996 Buick LeSabre Limited - Air Ride not inflating


Spray some soapy water with a spray bottle on the asi struts and check for leaks first.

Nov 30, 2009 | 1996 Buick LeSabre

1 Answer

Power outlet stoped working in front and back


Yes, it most likely did blow a fuse, most fuse boxes are under the hood you will see a fuse box close to the fire wall. Also there may be one on the drivers side, open the door and look on the side of the dash, look for a cut out to stick your finger nail in and pull out. Be careful with fuses as your car will have one for the air bags. read your drivers manual for the location of the fuse box and the fuse that is bad.

Apr 19, 2009 | 2000 Dodge Caravan

1 Answer

Power Outlets (cigarette lighter) will not work front or back


It sounds like the receptical has shorted out. Remove the receptical and make sure the ground wire (black wire) is in tact, and make sure the wire to the center of the receptical (power wire) is securely attached. If both are secure, the receptical is faulty and needs to be replaced.

Jan 16, 2009 | 1999 Plymouth Voyager

2 Answers

No power to cigarette lighter/power outlet (front & rear)..


Replace the 15 amp ACC fuse that is in the fusebox under the dash. See if this eliminates your problem.

Dec 08, 2008 | 1998 Toyota 4Runner

Not finding what you are looking for?
2004 Pontiac Grand Prix Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...