Question about 1998 Chevrolet Blazer

2 Answers

My abs light want go out on 1998 chevy s10 blazer it came on after i change my wheel bearing and ball joints

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Did you recheck to see if you plugged the speed sensors back in. The speed sensors are built into the wheel bearings on the 4wd models. If you did plug them back in, then one of you new sensors might be bad.

Posted on Nov 04, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

You may just need to re-set the code most parts stores can do this for you.

Posted on Aug 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs


sounds like the anti lock pump is gloing out

Oct 27, 2012 | 1998 Chevrolet Blazer

1 Answer

I have a problem removing the bottom ball joints on 2003 chevy trail blazer need step by step please.


remove steering knuckle with wheel hub and bearing attached ,remove lower ball joint flange with a chisel,remove the lower ball joint using a ball joint press you can rent the press from some local auto parts store or purchased from harbor freight for about 60 bucks.

Feb 25, 2011 | 2003 Chevrolet TrailBlazer

1 Answer

How do u remove the front axle on chevy s10 2001


been there doen this, remove the wheel, brake caliper and pad's, brake rotor, 4wheeldrive hub wheel bearing and abs asembaly ( this is all one unit, there are 3 bolts in the back side ot the spindle) upper and lower ball joints then finally the axel will come out, it will take alittle forse there is a snap ring on the diff end that takes a littel determination to get out, sound's like more work than it is, make shure u do one side at a time in case u foget how somthing goes and be carfull with the abs sensior wire and brake caliper hose! neither has to be diconected as long as u tie the componits up so thay are out of the way and won't fall any more proble fell free to ask i have owed s-10's all my life and curently have a 2001 s-10 blazer LT and a 1996 jimmy sle love them both and so does the wife! lol

Jun 05, 2010 | 2001 Chevrolet S-10

1 Answer

How to change front wheel bearing on 2001 blazer


You'll need to disconnect the tierod end from the steering knuckle, remove the caliper, caliper carrier, rotor and disconnect the ABS plug. Then disconnect the upper and lower ball joints and remove the steering knuckle. The wheel bearing hub has 3 bolts holding it to the steering knuckle, from the back side.

May 11, 2010 | 2001 Chevrolet Blazer

4 Answers

I have a 1997 Blazer. The ABS light comes on intermittently. When the ABS light is on the power windows and blower motor do not work. When the ABS light is off everything works just fine. Help????


That sounds strange about the power windows and the blower motor not working when the ABS light comes on. I happen to have a 99 Chevy blazer and I had the ABS light come on several times. There are ABS sensors on the two front wheel bearing hubs. If you take off the front wheels you will be able to see a black electrical cable that has 2 wires inside of it. This cable is coming directly from the ABS sensor on the wheel hub and is strapped to a bracket the is on the upper ball joint. From the hub it then goes to a plug connector that is under the protective flap that you lift to change your spark plugs. What I found that is a common problem is that wire tends to corrode or doesn't have enough slack in it when making turns and starts to pull and break. Examine that cable and if you see any breaks in it, that will cause the ABS light to come on. Also if you can get to the plug underneath the flap, unplug it and use a multimeter to see if you are getting any resistance on the two wires. If you aren't getting any resistance then your sensor is bad or you have a broken wire to the sensor. On my vehicle the ABS light kept on coming goin on and off intermitently and I found that wire from the sensor to the plug had a break in it. I stripped the wires back, spliced them together, soldered them and I used heat shrink tubing to cover the connections. The ABS light went out and it has been fine ever since. Hopefully this will solve your problem as well.

Jan 24, 2010 | 1997 Chevrolet Blazer

1 Answer

Ball joints goin out on a 89 chevy s10 blazer


The ball joints are going to be hard to due if you due not have an arbor press in your garage. They are not the kind that you can replace by yourself unforuantely without a press to press them back into the control arm. If you know a good cheap mechanic this would be a good route becuase a shop is going to charge you an arm and a leg to press these ball joints back in for you.

Apr 16, 2009 | 1998 Toyota Camry

1 Answer

Chevy blazer runs funny in 4 wheel drive


Hello,
Be sure that the joints on your front driveshaft are in good condition, hope this helps, good luck

Apr 03, 2009 | 1998 Chevrolet Blazer

1 Answer

86 blazer front wheel barrings how to ??


Hi there. If by gears you mean the splines on the end of the half shaft, you need to seperate the lower ball joint, if not done already, put the splines in the hub first and then hook the new bearing hub up to the lower control(ball joint) with the shaft already in place.

Mar 02, 2009 | 1986 Chevrolet S-10 Blazer

4 Answers

1998 Chevy S10 pickup backup lights don't work


Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Sep 06, 2008 | 1991 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

927 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...