Question about 1987 Mitsubishi Mighty Max

1 Answer

Dear Sir, How do you change an 87 mitsubishi mighty max front shocks without any compression equipment? Please email me at brad8141@hotmail.com. Is there a book with instructions regarding this matter. It is a 2.0 engine two wheel drive truck.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 6,826 Answers

REMOVAL & INSTALLATION

  1. Support the vehicle safely on jackstands. Support it at a height which will allow sufficient room to reach the upper shock absorber mount.
  2. Remove the wheel.
  3. Remove the upper shock nut, washer and bushing.
  4. Remove the lower mounting bolt(s) and remove the shock from the vehicle.
  5. Install the shock absorber in the vehicle and loosely tighten the upper shock absorber nut. Make sure the install the bushings and washers before installing the upper nut.
  6. For 4WD vehicles, install the shock absorber so that the white paint mark at the lower side of the shock absorber faces the outer side of the vehicle. Install the lower shock absorber bolt(s). On 1992-95 Montero torsion bar suspensions, tighten the single lower mounting bolt and nut to 65-76 ft. lbs. (88-103 Nm). On all other vehicles (whether torsion bar or coil spring suspensions), the two lower shock absorber mounting bolts should be tightened only to 7-10 ft. lbs. (9-14 Nm). Fig. 1: Install the shock absorber so that the white mark faces toward the outside of the vehicle - 4WD vehicles, except 1992-95 Monteros Dear Sir,

How do you change - 86668006.gif
    Fig. 2: Install the bushings, washers and nuts in the order shown - except 1992-95 Monteros 86668007.gif

  7. On 1992-95 Monteros, tighten the shock absorber installation nut so that the dimensions shown in the illustration ( A and B) are at the standard values. These standard values are: A - 0.04-0.08 in. (1-2mm), B - 0.06-0.10 in. (1.5-2.5mm). WARNING
    When tightening the nut, be careful not to bend the stud pin of the washer assembly.
  8. On all other vehicles, once the lower mounting bolt(s) are tightened, tighten the upper shock absorber mounting nut all the way to the end of the thread on the shock absorber stud, then tighten the locking nut to 9-13 ft. lbs. (12-18 Nm).
  9. Install the wheel.
  10. Lower the vehicle to the ground. Fig. 3: When installing the upper shock nuts on 1992-95 Monteros, make sure measurement A is 0.04-0.08 in. (1-2mm)Dear Sir, How do you change - 86668008.gif"http://i.fixya.net/uploads/images/86668008.gif" alt="86668008.gif" class="h_mi" />
    Fig. 4: When installing the upper shock assembly, make sure its components are positioned as shown - 1992-95 Monteros 86668009.gif
Dear Sir, How do you change - prev.gif"http://arrc.epnet.com/autoapp/8666/8666CH08_Shock_Absorber.htm">Dear next.gif

Posted on Nov 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What years are the windshield for a 1990 Mitsubishi mighty max interchangeable?


Mitsubishi Mighty Max Parts & Accessories - JCWhitney

www.jcwhitney.com > Mitsubishi
Below you'll find a wide variety of Mitsubishi Mighty Max parts and accessories. Enter the year of your Mitsubishi Mighty Max to get a more customized product ...

Mitsubishi Mighty Max Cars and Parts ' eBay

www.ebay.com > eBay Motors > Cars & Trucks > Mitsubishi

eBayResearch Mitsubishi Mighty Max popular models, prices, photos and read reviews. ...Tell us what you thinkthis item - opens in a new window or tab. Mitsubishi Mighty Max. Share: Mitsubishi Mighty Max Model Years ... Mitsubishi Mighty Max · 1990 Mitsubishi Mighty Max · 1989 Mitsubishi Mighty Max · 1988 Mitsubishi Mighty ...

Mitsubishi Mighty MAX Parts, Mitsubishi Mighty MAX ...

www.carparts.com > Mitsubishi
Through the years, your vehicle's components will succumb to wear and tear, ... In addition to replacement Mitsubishi Mighty Max parts, you may also want to buy ...

Jan 11, 2016 | Mitsubishi Cars & Trucks

1 Answer

What is the torque for installing the crankshaft for the 2.4 mitymax motor?


Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi
Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

Oct 02, 2015 | Cars & Trucks

1 Answer

Change the back shock on a 1987 Mitsubishi mighty max 2.0 5 speed truck


Basically, remove the old one and fit a new one.:) If the shocks are inside a coil spring, you ay need to use 'spring compressor'. If it's using lef springs, it's very straightforward.

May 13, 2014 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

Other car make shocks substitute for Mitsubishi mighty max


Not sure what your question is, may I suggest trying MightyRam50.net forum. They are a very informative forum on the Mighty max pick ups

Aug 09, 2013 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

Where is the fuel filter located on a 1989 mitsubishi mighty max


the mechanical fuel pump for a 87 2.0 Mitsubishi is located in the middle of the intake manifold.

The manual says you can remove it without taking off the intake manifold but it is tricky.

Jan 17, 2012 | Cars & Trucks

1 Answer

Have a 93 MightyMax hit hard in front, considering replacing body


call your auto parts store and ask what yeasr have interchangable parts they have all the parts listed on computer and they can tell you what you can mix and match

Apr 15, 2010 | 1993 Mitsubishi Mighty Max

2 Answers

What's the firing order for a 1990 Mitsubishi Mighty Max (4.banger)?


1990 Mitsubishi Truck Mighty Max 2WD 2.4L FI 4cyl
The Firing Order mitsutrk01:
Firing order 1-3-4-2 --------- front | | of | 1 2 3 4 | Distributor rotates clockwise vehicle | | ---------

1990 Mitsubishi Truck Mighty Max 4WD 3.0L FI 6cyl
The Firing Order mitsutrk04:
Firing order 1-2-3-4-5-6 ------- front | 1 3 5 | of | | distributor rotates counter vehicle | 2 4 6 | clockwise -------


Hope help with this (remember rated this help).

Mar 12, 2010 | 1989 Mitsubishi Mighty Max

4 Answers

Location of fuel pump,1987 Mitsubishi Mighty Max,2.0 2wd


the mecanical fuel pump for a 87 2.0 mitsubishi is located in the middle of the intake manifold.

Jan 17, 2009 | 1989 Mitsubishi Mighty Max

Not finding what you are looking for?
Cars & Trucks Logo

580 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...