Question about 1999 Daewoo Leganza

1 Answer

1999 Daewoo Leganza How to set timing - 1999 Daewoo Leganza

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

You will need these tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers.

If you are doing this because your timing belt broke, you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley (the four Allen head bolts only not the 17mm bolt in the center.) Remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover, three clips on top and two 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center (TDC) on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover (notch in cover with notch in pulley) on the camshaft pulleys (intake cam line up the line on the pulley with the line on the inner cover) (exhaust cam line up the arrow on the pulley with the arrow on the inner cover) Now loosen the 13mm bolt in the belt tensioner and using the Allen wrench, rotate the tab until there is slack in the belt. Remove the timing belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the exhaust cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed, rotate the crankshaft over two revolutions and make sure is rotates freely, and your timing marks are aligned perfectly. If not, the engine will not run properly, tension the belt as needed. Installation is the same as removal. To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple. In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long. One more item that you might as well replace while you are in there is the cam position sensor if you have not already replaced it as there have been issues with them, and the timing housing has to be opened to get to it. The timing is set at: 6 degrees (both manual and automatic transmission)

Posted on Feb 05, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timming belt settings


Here's a link Rebecca on your timing belt,your vehicle is hard to find stuff on. How to set timing belt on daewoo leganza 2001 Daewoo Leganza

Aug 11, 2015 | 2001 Daewoo Leganza

1 Answer

Timing setting daewoo leganza


http://www.tradebit.com/filedetail.php/189127366-daewoo-leganza-service-manual

Aug 28, 2012 | 2000 Daewoo Leganza

1 Answer

The timing marks for a 1999 daewoo leganza


Both cams have a notch in their edges, those go straight up parallel with each other pointing at the marks on the valve cover. Crankshaft pulley also has a mark that lines up with a mark on the timing belt rear cover.

Dec 20, 2009 | 1999 Daewoo Leganza

2 Answers

My Daewoo dies after it warms up


1999 Daewoo Leganza Daewoo leganza stop running when I slowed down just after I noticed a hesitation while driving at a steady speed. It wouldnt start up again until I waited for awhile.

Apr 12, 2009 | 1999 Daewoo Leganza

1 Answer

1999 daewoo leganza


Probable head gasket is leaking coolant into the cylinders

Sep 10, 2008 | 1999 Daewoo Leganza

2 Answers

Need a picture diagram of 1999 daewoo Leganza timing belt setting or mars?


need a picture diagram for timing marks nubira 2001 2.0L

Jul 20, 2008 | 2002 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Leganza Logo

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Marvin
Marvin

Level 3 Expert

83810 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...