Question about Hyundai Tiburon

3 Answers

Code b1360 firing circuit #3 / and what is he bpt?

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 83,810 Answers

And what is he bpt?? what does that refer to?

Posted on Nov 03, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a kia carens 51 plate and i have had a code reader on it and its p1127 does any one no what it is?

Posted on Nov 06, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,413 Answers

HYUNDAI OBDII DTC

P1100 Manifold Absolute Pressure Sensor Range/Performance

P1102 Manifold Absolute Pressure Sensor Circuit Low Input

P1103 Manifold Absolute Pressure Sensor Circuit High Input

P1123 Lang Term Fuel Trim Adaptive Too Lean

P1124 Long Term Fuel Trim Adaptive Too Rich

P1127 Long Term Fuel Trim Multiplier Too Rich

P1128 Long Term Fuel Trim Multiplier Too Lean

P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)

P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)

P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)

P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)

P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)

P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)

P1372 Segment Time Incorrect

P1400 Manifold Differential Pressure Sensor Circuit

P1440 EVAP System Vent Solenoid Circuit

P1443 EVAP System Fault (Fuel Tank Cap Missing)

P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)

P1511 Idle Control Valve Command Signal Shorted (Coil 2)

P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)

P1521 Power Steering Switch Input Circuit

P1529 Customer Snapshot Request VIA CAN

P1552 Idle Air Control Valve Closing Coil Circuit Shorted

P1553 Idle Air Control Valve Closing Coil Circuit Open

P1586 Encoding Signal Circuit Not Rationale

P1602 Serial Communication Fault with Transmission Control Unit

P1605 Rough Road Sensor Circuit

P1606 Rough Road Sensor Circuit Not Valid

P1611 MIL Request Signal Circuit Low Input

P1613 ECU Self-Test Failed

P1614 MIL Request Signal Circuit High Input

P1616 Main Relay Fault

P1623 Diagnostic Lamp Power Stage Fault

P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit

P1625 Cooling Fan Relay High Circuit

P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

Posted on Nov 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced:plugs,wiresdistributor,fuel pump.truck wouldn't start before but now it starts but i am getting po135,po141,po147.po300 codes


P0135 means 0xygen heater circuit malfunction, P0141 mean 02 heater circuit bank1 sensor 2 (this is catalytic monitor) P0147 means 02 heater sensor circuit bank 1 sensor 3, P0300 is random misfire. You will get all the 02 code because of the misfire correct the misfire and the 02 should correct.We will start with the plug wire and make sure the firing order is correct 1996 chevy blazer that will make it a 4.3 engine size check the firing order firing order is 165432 also check the coil (it has a tendency to short you will know if it is) cansmo_181.gifcansmo_182.gifmake sure the distributor rotation is check

Sep 09, 2011 | 1996 Chevrolet Blazer

1 Answer

What is a BPT valve and does it effect the E.G.R. valve? Can you check a BPT valve?


My Nissan truck manual for the same engine does not say what it is or what it does but said how to check it. It said to take the hoses of the valve the top two hoses are likely at the same place and 180 deg from eachother. The last hose connector is perpendicular and at the bottom. It said to plug one of the top holes and apply pressure to the bottom hole while applying pressure to the bottom hole. Then you apply a vacume or suction to the open top hole. If you can pull air then the valve or casing is bad and should be replaced. This manual did not second refer to the E.G.R valve from the BPT. The BPT valve was under the Emissions control section. Once this valve has been checked it said to check the EGR valve connected close by. Similar test but air pressure was supposed to be more resistant or something, but may allow some air flow or something?

Oct 17, 2009 | 1996 Nissan Pickup

1 Answer

Failed e-check check engine code egr solenoid valve


go here and read files, especially all about EGR.

http://autos.groups.yahoo.com/group/villagerquest/

could be plugged passages, a bad BPT, bad EGR valve, bad EGR solenoid. We'll help you diagnose.

May 23, 2009 | 1998 Mercury Villager

2 Answers

Check engine light for a 1995 Mercury Villager is on


Couple of suggestions;

Phone around to some car repair places and see if they have an instrument to read/clear the codes from your '95 Villager. Some shops still have and use them.

Chances are you might need a new BPT hose. This is a very easy and inexpensive fix. My check engine light was on for about 75,000 km before I replaced the BPT hose and since then the check engine light has never come on again.

The Villager is still going strong at 375,000 km.

bikerbc

Mar 14, 2009 | 1995 Mercury Villager

3 Answers

2002 NISSAN FRONTIER


sounds like a problem in the egr valve or the porting through the egr valve or maybe a vaccuum line that has something to do with monitoring it. make sure there are no vacuum lines near it that are leaking and is there a difference in the idle that you may notice.

Oct 24, 2008 | 2002 Nissan Frontier Crew Cab

1 Answer

91 mazda gtx


On a mazda gtx (4x4 turbo) 1840cc
oil bolts and tighten in 3 even stages

30 ft lbs or 60nm
40 ft lbs or 70nm
60 ft lbs or 81nm

torque sequence is:

inlet side
8 4 2 5 9
10 6 1 3 7
exaust side

Oct 17, 2008 | 1991 Mazda 323

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,001 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

83810 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...