Question about 1999 Buick Regal

1 Answer

What are the measurements for the tie rod ends for proper alignment. I am replacing both inner and outer tie rod ends on both sides and I can't go off the originals since the car was so far off alignment to begin with.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 398 Answers

When replacing the tie rods ... You need to count the turns to unscrew it off. Then replace it with the same amount of turns

Posted on Nov 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My durango had a tie rod break on the front drivers side. I took the piece to the auto parts store and they need to know if it is an inner or outer and the size is either 15mm or 16mm. I do not know how to...


It may be stuck on defrost cycle due to a bad timer... is there an adjustable switch that you could adjust it should start up... let me know......

Jul 20, 2011 | 2005 Dodge Durango

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

Stearing is pulling at 1 quarter turn both sides


Your front end would need alignment, you could also have a tie-rod end problem. There are both inner and outer tie-rod ends and they are quite inexpensive to replace. Your tires should be prematurely wearing also, this is also another sign of being either out of alignment or in need of a tie rod end. Hope this helps!

Jul 30, 2010 | Hyundai Santa Fe Cars & Trucks

1 Answer

Impact bent the right front tie rod. how can it be removed for straightening or replacing?


First loosen the jam nut with a 21mm wrench. Then use vise grips or whatever you have to make sure the rod can be turned that goes into the outer tie rod. Then remove the cotter pin and 17mm castle nut. Strike the hub where the tie rod goes through with a hammer repeatedly until the tie rod pops out of the hole.

Then simply unscrew the tie rod end and replace it. If the inner tie rod end is also damaged, or the rod is damaged you will need to replace them as well. Inner tie rods have a special tool to remove them, see your local auto parts store.

Remember, replacing an outer tie rod end changes your cars toe (alignment). You will require an alignment after replacing it, even if you think the car drives straight.

Good luck!

Nov 30, 2009 | 2002 Hyundai Accent

1 Answer

Repair inner tie rod end of 1997 dodge avenger


f734654.gif #3 is the inner tie rod and it is simply screwed into each end of the steering rack. Raise and support the car remove the wheel and you should see where it is connected to the outer tie rod. There is a lock nut that you'll need to loosen slightly to get the tie rod off. You will need to get a wheel alignment once done but by slightly loosening the lock nut, you have a good reference of how it should be once done. Once loose, you should be able to turn the tie rod by using a wrench on the flattened area on the rod. Once disconnected from the outer tie rod end, you should be able to remove the dust boot covering the inner tie rod connection. Mine came right apart so hope you have no problems. After you have it out, here is where the loosened locknut comes into play. Put the new and old tie rod side by side, line up the ends that attach to the rack and pinion then mark the new rod so you know how far to put the lock nut on the new tie rod. Simply tightly screw the new one onto the rack and pinion put the boot back, screw on the lock nut to the mark then attach the tie rod to the outer tie rod end up to the lock nut then tighten the lock nut against the outer end. Get the tire back on, lower the car and Voila, done. Now go get an alignment.

Nov 18, 2009 | 1997 Dodge Avenger

1 Answer

How to align a 94 gmc sierra


Inner and outer ball joints?? If you mean tie rod ends u will need to set the toe in. Mesure the distance across the back of the tires and then across the front. The differance is ur toe in. Best take it to a wheel align shop and have it done properly it will save you a lot on tires.

Jul 14, 2009 | 1994 GMC Sierra

1 Answer

Steps to replace steering componets


Jack up car, remove wheels, pull cotter pins out of outer tie rod ends, tap tie rod ends till joint pops out, next unhook bolt that holds steering wheel to the rack and pinion, disconnect the power steering hose and drain fluid in a can, next remove mounting bolts from the rack and pinion that holds it to the frame, if the exhaust is not in the way yo can get it out without to much trouble, after removing the hoses and the steering knuckle drop the unit down in one piece, book time calls for 4 hours to remove and more time if you replace the inner tie rod ends, go buy a rebuilt unit at the parts store will cost about $400 fo a rebuilt unit, replace bot inner and outer tie rod ends, to install is the reverse procedure, the steering wheel shaft is keyed for it to fit in one way make sure it is pointing straight and the steering rack is centered get that started first then bolt up hook up lines and tie rod ends, then adjust tie rod ends to get alignment close, you can turn the wheels one at a time with a round file to make a mark on the tire and do both sides then with a tape measure check on the two lines on the wheels front and rear it should be no more than 1/8 towed out in the front if it is more adjust then take it to a alignment shop and get a four wheel alignment.

Jun 21, 2009 | 1999 Chevrolet Tracker

1 Answer

Replace rack/pinion


The book calls for about 5 hours labor with a lift, air tools, and experience. It's a tough job. Here are a few tips, Take the lines loose from the rack; not the pump. With the tires off, Remove the nuts from the outer tie rods.Run the nuts back on the tie rods stud and hit the steering knuckle where the tie rod's stud goes through.This will free the stud. Remove the steering shaft from the rack.(take the bolt all the way out.Remove rack mounting bolts. Twist,pull ****,and fight the rack out the side of the car with the most room. The new rack will have inner tie rods already installed. Make sure the new rack is centered.(Turn left then right count the turns then center same # of turns from left to right). Count the threads or measure from the outer tie rod's jam nut to the last thread on the inner tie rod.(you can leave the jam nut in place and take the outer tie rod off and measure from the jam nut to the end of the rod.)Install the outer tie rods. Replace rack in car. hook up steering shaft.Bolt up rack. Hook up lines. Add fluid and work rack back and forth to bleed air. recheck fluid. Have it aligned. (or just take it to a shop.This job is going to be a nightmare!!!)

May 23, 2009 | 1999 Ford Taurus

2 Answers

How do I install driver side inner tie rod on my 1997 chevy cavalier?No room to work. Do I need to remove whole rack and pinion assembly?


you don't need to remove the whole rack but do need a special tool called inner tie rod tool. can be bought or borrowed form most auto parts stores. first remove wheel. next loosen the jam nut on inner tie rod at the end of outer tie rod. remove cotter pin and nut on outer. use seperator or pickle fork to seperate outer from knuckle. then remove the clamps on boot and remove. then take tie rod tool and find the right size end and turn with 1/2" ratchet or breaker bar. it will turn hard at first cause of it being staked on to the threads. when it is off install new part with loc-tite on threads and tighten. when tight crimp inner flanges with either plier or hammer and punch to the rack. install in reverse order. remember to measure distance from clamp on outer side of boot to jam nut so you can get the alignment close until you get to shop for alignment.

May 05, 2009 | 1997 Chevrolet Cavalier

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

Not finding what you are looking for?
1999 Buick Regal Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...