Question about 2001 Chevrolet Corvette

2 Answers

Front turn-signal bulb burned out.

My owners manual does not describe how to replace the front turn-signal bulbs. I can't find the access port in the engine compartment. Please help. Thank you.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

It is a tight squeeze, but you can get your arm down past the headlight to the brake cooling duct and pull the brakeduct off the nose of the car back and to the side. Then you can reach through that hole and replace the turn signal blub

Posted on Sep 14, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need more detail of vehicle , if its a c5 corvette there is 2 ways through bottom or through top , bottom ,there is a openable panel apprx 1 ft by 2ft wide both sides it is openable jack car up use safety devices unscrew apprx 5 screws holding your right or left side air dam ,a little farthe back over the edge into wheel well youl find a couple more to remove open access , or from the top squeeze your arm down alongside headlamp "while it is up" reaching bulb with fingers turn slightly it comes outwith holder remove then install new bulb repeat removal in reverse for more room you can remove the 3 screws holding yiour headlite surround on, slip it off, lot more room

Posted on Jun 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Passenger side turn signal flashes fast both front and rear possible causes


The indication would be a turn signal bulb has burn out. Since each side front and rear are wired together you will have have someone tell you which bulb is not working, when you select turn.
Remember each bulb has two filament running light and turn.
owners manual should tell you what type bulb. Buy a few spares.

Sep 21, 2016 | Cars & Trucks

2 Answers

Replacing front right turn signal bulb


what are the ways u tried....
open the bonnet, nw u can find an access to the front right lighting assembly.... u can change the bulb nw 

reply back

Jun 15, 2008 | 2007 GMC Yukon Denali

2 Answers

Front right turn signal flashes fast left side does not


when turn signal blink faster means there a bulb burn front or rear of car

Oct 11, 2014 | 1996 Pontiac Grand Am

1 Answer

The left rear turn signal on my 1998 Aurora will not flash. According to the Owners manual the correct lamp is a 3057. I have tried 2 new 3057 bulbs they light up but won't flash. The right turn...


Normally, it means either the front or the rear bulb is burned out. If front and rear bulbs are good, and that means both lamp filaments in both bulbs are good. It could be the flasher, a bad ground, a bad bulb socket, or the turn signal switch.

Aug 27, 2011 | 1998 Oldsmobile Aurora

1 Answer

Changing bulb for front right turn signal


The procedure for changing the front bulbs is described in the owners manual but it is not easy. It is the same for the headlights, turn signals, and fog lights. First, turn the wheels in (to the left for the right side) and then turn off the vehicle. You will then loosen the screws on the inside plastic wheel well until you can bend it out of the way. You can then reach inside, and the bulbs all come out with a 1/4 twist to the left. Make sure you remove the old gasket ring, and install the new bulb with only one gasket. Screw the wheel well back into position and you are done.

Apr 07, 2010 | 2006 Chevrolet HHR

1 Answer

Turn signal lamp is inside of headlamp housing


you want to change the turn signal light? front yes to what ever side you need to change the access is to the back of the head light assy. Front Turn Signal Light Bulb Size: 1157A
Rear Turn Signal Light Bulb Size: 1157
check too owners manual will show you how to thanks Lee let me know how it goes thanx

Dec 26, 2009 | 2003 Ford Crown Victoria

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

Turn signal bulb 2000 Mercedes s500


If you have a owners manual then the method is described there.

Sep 13, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

Rt front turn sighal burned out - how to access bulb to replace


There is a latch to the Van's outside just insert a flat blade screw driver and the turn light assembly will swing toward the middle of the van.

Once open the lamps twist out.

Dec 18, 2008 | 2003 Chevrolet Express

2 Answers

Replace front driver signal light bulb


Depending on whether it is the front or the back turn indicator light will determine on what needs to be done. If it is the front turn indicator light open the hood of the car you may need to take the entire headlight out. The headlight may have screws, take the screws out then the front light will come out from the outside of the vehicle replace the burned out bulb. The bulb should snap right in and then put the headlight back in make sure you put all screws back in from the inside of the hood. Step2 If it is the back turn indicator light, go through the trunk of the vehicle. If there is a panel covering the lights you must unscrew the panel and then replace the burned out light bulb. Some panels can be folded down without removing all of the screws to access the lights. This light may not require for you to pop the entire light out you maybe able to just replace the bulb. After you have replaced it screw the panel back into place. The back light should not require the entire light to be lifted out just a simple bulb replacement. Step3 In replacing either the front or the back indicator light you must gain access to the turn signal housing which is usually in the same case as the headlight or your rear lights. It is very helpful to also get the owners manual out this will tell you exactly what type of bulbs you will need to get to replace the indicator bulb.

May 29, 2008 | 2005 Cadillac SRX

Not finding what you are looking for?
2001 Chevrolet Corvette Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...