Question about 2001 Lexus ES 300
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
according to the manual i have... it has three.... one in the exhaust manifold.... and two in the exhaust pipe..... slightly vauge on the exact location of the last two sensors... but looks like it is after the catylitic converter.
Posted on Apr 15, 2009
in order to replaced the bulb, u go from inside the car (back Seat). The housing for the brake light will shift to the left (passanger side) then slide out, disconnect connector and replace buld
Posted on May 06, 2009
Hello, I have a 2000 ES300 and while the body style is different believe the newer model still has the rear deck mounted sub-woofer that you are referring to. The process of removing this speaker would start off the same as if you were going to replace the third brake light also located in this housing. Using a flathead screwdriver work your way around prying/popping up all four corners of the speaker grill covering the speaker that have the retainer clips. Once you disengage the clips work/maneuver the grill up and towards you gently and it should slide out. The bulb for the third brae light will be attached to this speaker grill, disconnect the snap wire from the bulb and you should have a clear visual of the speaker and the four bolthead screws securing it. Remove these screws and your almost home free. The next part might be slightly more difficult. If the speaker s simply connected by a clipped on wiring harness, just detach.On my 2000 ES300 i have the pioneer system(Not Nakimichi) and the 2 wires (one black, and one red) are soldered directly to the speaker. You can take a soldering iron(maybe a battery or gas powered one unless you have an inverter) and remelt the solder to remove the wires or you can elect to simply cut the wires. If you choose to cut them make sure you cut them as close as possible to the soldered joints so you have plenty of wire left to install the replacement speaker.Then install replacement either soldering or using crimp clamps and reassemble. ( Note if you simply want to add a aftermarket amplified sub-woofer you don't need to remove the sub-woofer out of the housing. You can tap into the wire leads and run it directly to the amplifier. Just cut one of the wires leading to the stock sub-woofer so it doesn't also come on and potentially blow while the radio is on. This will also prevent any bass humming when the radio is shut off but the aftermarket amplifier is still on because once one of the wires to the stock sub-woofer is disconnected or cut it breaks the circuit. Hope this helps.
Posted on Jul 22, 2009
Hello there here is a good site to give you more information and general idea of the cost involved Lexus ES Forum [Lexus Forum Archive] - Page 3 - Lexus Forums how to tell if it needs a tune up...? what is the value of my ... About how much does it cost to fix a '92 lexus ES300 with a ... 1997 Lexus ES 300 ...www.planetlexus.com/lexus-forums/archive/index.php/f-4-p-3.html - Cached
Posted on Aug 18, 2009
Tips for a great answer:
Jun 20, 2017 | Lexus Cars & Trucks
Sep 06, 2013 | 1999 Lexus ES 300
Dec 07, 2010 | 2001 Lexus ES 300
Aug 25, 2010 | 1996 Lexus ES 300
Jun 03, 2010 | 1992 Lexus Es 300
Apr 01, 2010 | 2000 Lexus ES 300
Aug 18, 2009 | 1997 Lexus ES 300
Jun 17, 2009 | 2001 Lexus ES 300
Apr 21, 2009 | 2001 Lexus ES 300
Apr 14, 2009 | 2002 Lexus ES 300
331 people viewed this question
Usually answered in minutes!