Question about 1996 Geo Prizm

1 Answer

Is there a way to read the trouble codes with-out a computer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

No, you need a scanner to read codes. Some Auto Parts Stores will read codes and not charge you.(AutoZone, Advance Auto Parts, PeP Boys)

Posted on Nov 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 f 150 od light flashing.


The OD light flashes when a fault is detected in the computer controlled transmission, you need that fault code read with a scan tool.

Jan 05, 2018 | Cars & Trucks

2 Answers

Determining what error codes mean


OBD-II Check Engine Light Trouble Codes

https://www.obd-codes.com/trouble_codes/
  1. Cached
  2. Similar
OBD-II OBD2 Diagnostic Trouble Codes. Definitions and suggested repair procedures.

How to Read Diagnostic Trouble Codes - AA1Car.com

www.aa1car.com/library/cm40122.htm
  1. Cached
  2. Similar
HOW TO READ DIAGNOSTIC TROUBLE CODES. 1. Locate the 16-pin OBD II diagnostic connector (usually under the dash near the steering column). Note: On some vehicles, it may be necessary to remove a knee bolster panel

obd11 fault codes Google Search

Dec 07, 2017 | Cars & Trucks

1 Answer

My 2007 Toyota isis iaz.read code P0191


Anon, Trouble code P0191, You may need a good tech. with scan tool to read and test system.
  • Fuel Rail Pressure Sensor Circuit Range/Performance,computer see's signal from the Fuel Rail Pressure Sensor and/or its circuit is sending erratic readings, indicating a fuel pressure condition that is abnormal. Problems could be out of gas, leaking fuel, faulty fuel pressure sensor, bad wire or plug in circuit,fuel pressure regulator, the fuel pump could be faulty also. Check the attached links,instruction and guides, Good luck
    "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
P0191 OBD II Trouble Code

P0191 Fuel Rail Pressure Sensor Circuit Range Performance

RAV4 2001 Trouble Code p0191 probable solution Toyota Nation Forum Toyota...

code P0191 2007 Toyota Google Search

May 03, 2016 | Toyota Cars & Trucks

1 Answer

2002 lincoln ls cutting out real bad and engine light on


The engine light on means there is a trouble code waiting in the cars computer memory to be read. major auto parts stores have code readers and will read out the code for free. This is the place to start the trouble shooting process.

Feb 13, 2011 | 2005 Ford Lincoln Continental

1 Answer

How to repair when the check engine light comes on.


You 'll need an OBD II code reader to read out the trouble code stored in the engine computer's memory. Major auto parts stores have these readers and will read out your codes for free. With the code you can begin to trouble shoot the problem.

Feb 11, 2011 | 2004 Toyota Camry

1 Answer

I have an 08 Mazda 6 4 cylinder, when I went accelerate my car hesitated then the check engine light came on, what is the problem


The check engine light indicates that a trouble code is stored in the vehicle's computer memory. An OBD II code reader is needed to read out the code and explain it. Major auto parts stores will use one of these readers to read out your code for free. With the code, a diagnostic routine can be developed to trouble shoot the problem.

Feb 11, 2011 | 2008 Mazda MAZDA6

1 Answer

Service engine light is on even after disconnecting the battery for five minutes


The service engine light is on because the built in onboard diagnostic system it trying to tell you that it has diagnosed a problem and stored it as a trouble code in the vehicles computer. Disconnecting the battery wont make it go away. You should get the codes read, and the code reader can reset the light, but if the problem is still there the light will come back on pretty soon. Most major auto parts stores will read these codes for you for no charge. Write down the code that is in your trucks computer so you will know what the computer logged as trouble.

Dec 18, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Check Engine Soon light has come on. How do I check for codes?


Take the car to an autozone and they can read the trouble codes stored in the computer.

If you do not want to go to autozone, take the car to a dealership and the codes can be read by a qualified mechanic. the check engine light means a trouble code has been stored in the vehicles computer.

Oct 30, 2010 | 1994 Saturn Sl

1 Answer

Car wont go faster than 50 mph


The car's computer is in limp home mode and will require service. You need to connect a scanner to the computer to read it's diagnostic trouble codes. You probably have trouble with the transmission. Post the trouble codes and you can be given more advice.

Sep 11, 2009 | 1999 Chrysler 300M

1 Answer

Trouble codes for 1993 Dodge Daytona with 3.0 liter


CODE 12
Trouble Code 12 is a special case code that is not logged into the ECM's Non-Volatile Memory (NVM) when detected. When the ignition is "ON" and the ECM detects no ignition reference pulses coming from the ignition module, it illuminates the Service Engine Soon lamp.
CODE 22
Trouble Code 22 indicates that the Throttle Position Sensor (TPS) is reading abnormally low. TPS volts should be close to 0.42 V at closed throttle and rise smoothly in about 0.02 volt increments to a maximum reading of about 4.85 volts at WOT
CODE 35
Trouble Code 35 is not used in the Turbo cars. If this code appears while a computer is connected to the ALDL connector, it is probably the result of a bad cable connection at the PC or the ALDL connector. Reseat the cable connections.

Aug 24, 2008 | 1993 Dodge Daytona

Not finding what you are looking for?
1996 Geo Prizm Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...