Question about Chrysler Neon

1 Answer

Immobeliser key fob problems

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Probably just needs resetting job for chrysler or a good autolec could remove imobiliser altogether

Posted on Jun 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed battery on my key fob and it won't work


What is year--make--model?
The key fob is a transmitter so there has to be a receiver in the vehicle. At the moment, I can't tell if problem with transmitter or receiver? Can you try a different key fob? Where applicable, if key fob needs to be programmed, maybe the info is in your owners manual?

Apr 10, 2016 | Cars & Trucks

1 Answer

My 3 door peugeot 206 will lock ok with the key fob but will not unlock with the key fob, help!


Sounds like the unlock button on your key fob is the problem, try your spare key fob, if you don't have a spare fob, it's time to get a new one.

Dec 06, 2015 | 2004 Peugeot 206

2 Answers

Immobeliser kicked in when battery died


Three possible cures for your situation. Start with the least complicated. BeCM basic reset.
-Disconnnect the negative lead from battery.
-Put key in ignition and turn to second position (all on)
-Leaving the driver door open, return to engine compartment and replace the negative lead
-Close the hood
-Back to drivers seat, all the bells and whistles should be going off
-Turn the key to the starting position. Turn it over.

TIP: You MUST HAVE a healthy fully charged battery for any success resetting the immobilizer.
If no help then we are on to the (emergency key access) EKA door lock method.
Good luck with the simple solution. Message me direct if unsuccessful and I will forward the detailed EKA procedure.

Jul 09, 2014 | 1997 Land Rover Range Rover

1 Answer

05 dakota doors lock with fob but won't unlock with fob


Your FOB has gone bad. Try your other FOB just to make sure and let me know ....

Apr 14, 2013 | 2004 Dodge Ram 1500

1 Answer

Keyless entry remote wont progam


It will not unlock the door the first time you push the button. This only registers the key fob ID into the computer. When you press the button on the key fob, press it only once and wait for the hazzard lights to flash twice again. Then open the driver's door. The key fob will not become active until you open the driver's door.

If your hazzard lights do not flash after you press the button on the key fob, there is most likely a problem with the key fob. Either it is not the correct key fob for your vehicle, or the battery is not in correctly or the key fob is defective.

The only other advice I can give you is to have it programmed with a scan tool. This way, the scan tool can verify that the computer in your vehicle is receiving the signal from the key fob.

It can be done either way, but if the "no scanner" way does not work, the rest of the system should be checked for possible problems.

Dec 12, 2011 | 2005 Nissan Altima

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

4 Answers

My 2006 cadillac sts key fob all of a sudden is not working it says no fob detected and i have the fob what can b wrong??


Some late model fobs contain electronics beyond the push buttons.
Batteries are replaceable...small screws may let you do this.
If the battery is not the cause....a replacement fob may be expensive. A road service technician can probably troubleshoot and replace cheaper than dealer !

Sep 07, 2010 | 2006 Cadillac STS

1 Answer

Having problem with the beeper for my honda pilot 2004 its not the bateries can't open the dors with beeper..


In the case the battery was drained in the keyfob - try reprogramming it.
Here are the instructions.

The process is pretty easy....1st) get in the vehicle and close all doors, windows, hood, and trunk.
2nd)put the key in the ignition and turn it to the second position...while in that position (w/out starting) push the lock button on the good key fob you already have. (if you don't already have a good fob, then press the lock button on the new key fob) (do this all w/in 5 seconds)
3rd)turn the key off
4th) turn the key on to the second position and press the lock button on the fob.
5th) turn the key off
6th) turn the key on to the second position and press the lock button on the fob.
7th) turn the key off.
8th) turn the key on to the second position and press the lock button the the fob.....the press the unlock button on the fob..........Now press the lock button on the new fob...press the unlock button on the new fob....
9th) tun the key off.....remove the key from the ignition and test to make sure that the new fob and the old fobs both work now.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 06, 2010 | 2004 Honda Pilot

1 Answer

Porsche 2000 911 Carrera. Key fob problem


each vehicle is different put the key in the ign. turn key on press door lock/unlock at the same timehold button for 10 sec see if any lights on the dash inst. panel blink if they do that means that the key fob was programmed to your vehicle i recommend a new key fob this will give you definative instructions on how to reprogram your fob

May 04, 2010 | 2000 Porsche 911 Carrera

1 Answer

I MMOBELISER NOT RESPONDING


the chip reader in the ignition is probably an issue.

May 08, 2009 | 1997 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...