Question about 1995 Ford Mustang

1 Answer

95 mustang Hi. my problem is the electic fan for cooling the engine does'nt work. when you put power to it the the fan works. the fuse is good and power to both sides. the temp. sender was replaced along with the thermostat. The car runs fine just that when the car gets up to temp. the fan does'nt work. would the relay cause be my problem.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Hi the temp" sender "in this case is a thermostatic switch normaly with 2 connections put an ohm meter across the connections when engine is cold it will show nill or full scale leave meter connected run motor up untill it is hot meter needle should have moved 1 way or the other if it did not the relay is at fault chris merlinv12

Posted on Jul 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Coolling fans dont work


Check for a blown fuse----look at it & test it
Check for & TEST any fan relays-have to remove them to do so
Then unplug the cooling fan & put battery voltage to it

If the fuse is good,the relay works,the fan works,you may need
a wiring diagram & do some internet searching to find a temp sensor or switch--odds are it will be in the radiator or cooling system somewhere.

Check for wire connectors being off

Have to check the radiator for leaks & the coolant system
for leaks & at least partially remove the radiator, to get rid of
leaves & other road dibris,bird feathers & such

Aug 15, 2014 | Pontiac Grand Am Cars & Trucks

2 Answers

Engine coolant fan wont come on. The fan motor is fine. whats next?


You still have many other components in that system that has to be in working order for the cooling fan to work properly. The cooling fan is turned on when engine temp reaches a predetermined temp, usually around 220-230 degrees F. the ECT (engine coolant temp) sensor siganls the ECM (Engine Control Module) to ground the cooling fan relay or cooling fan module(if equipped) and if the cooling fan fuse is good and the fan has power to it the realy will complete the ground for the fan to run. You may need to have a qualified technician diagnose the problem if the obvious things like fuses and good grounds are not the problem.

Hope this helps.

Oct 22, 2013 | 1999 Ford Contour

3 Answers

Hello, I have a 1989 chevy 3/4 ton pu with a 350 motor. It reads 230-250 on the heat gauge. I had replaced both heat sencors on the side and the top of the block. Has a 180 theromstat fail safe. When...


faulty temperature sensor or dash gauge. Both do not conjoin to the ECM so I would replace the temp sensor on the engine first which is fairly cheap

Aug 24, 2011 | 1989 Chevrolet C1500

1 Answer

95 3.6l mustang good battery and fuses absolutely no power to the car anywhere


CHECK TO MAKE SURE IT HAS POWER TO THE FUSE BOX IF IT DOES THEN CHECK AND MAKE SURE THAT YOU HAVE A GOOD GROUND FROM THE BATTERY TO THE CHASSIS & FROM THE CHASSIS TO THE ENGINE

Dec 04, 2009 | 1995 Ford Mustang

1 Answer

Radiator fan not kicking in.but works when power put to it directly.where is the sensor located ? this is in a V-6 '95 mustang..


Check fan relay which is either on the firewall or front corner of engine comp. should be a black square box with 3 wires going to it

Jul 04, 2009 | Ford Mustang Cars & Trucks

2 Answers

Cooling fan cuts off


The fan relay is not functioning correctly or the new sensor is defective.

Jun 02, 2009 | 1995 Ford Mustang

2 Answers

Cooling fan wont kick in


Could be the FAN MOTOR, COOLING FAN TURN ON SENSOR, even the PCM. There are 2 fuses . Also check fuse panel under hood in engine compartment

May 08, 2009 | 1995 Cadillac Seville

2 Answers

Fuse box diagram 05 mustang


the fan on-off temp can be adjusted via hand held programmer. The only time I have herd mine run is with the a/c on. when a/c is not on i put a lower set point in and the engine fan/s came on.
Stock set points are 196 and 210

May 29, 2008 | 2005 Ford Mustang

Not finding what you are looking for?
1995 Ford Mustang Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...