Question about 1998 Mercury Tracer

1 Answer

Rearblinker bulb 98 tracer

How to change a bulb without braeking the basil

Posted by on

1 Answer

Open the trunk and un screw the tail light and there pugs in the the back you unscrew and pull out.

Posted on Sep 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to change the power steering hoses on a 98 mercury tracer, need help finding them


They usually run under the engine. I have a new shop manual & wiring book for this car. $25 if interested. $5 postage.

Sep 29, 2011 | 1998 Mercury Tracer

1 Answer

How do i change bulb in headlight on mercury tracer? 1991.


1. Open the hood and remove the screws holding the headlight assembly in place. These screws are located on the back side of the headlight assembly.

2. Slide the headlight assembly forward.


3. Unplug the electrical connector running to the headlight ballast.


4. Slide the new headlight assembly and bulb into place, connect the connector to the headlight ballast and secure the assembly with the factory screws.

Feb 24, 2011 | 1991 Mercury Tracer

1 Answer

How do you change a tail light bulb on a 1997 mercury tracer?


is there a special tool needed to remove clamps they wont come out

Sep 24, 2010 | 1997 Mercury Tracer

1 Answer

I want to change the light bulbs in my dash board. how?


look at the whole basil, there is a front cover, that is over, the basil, take all screws out of the plastic cover, then you will have screws holding the actual basil in, i believe they are either a quarter inch or five sixteenth, take them out the whole speedo cluster should pull out some , you may have to take speedo cable loose, also they might be some plugs you have to remove, mark them if needed, to remember where they go, once that is done, flip the cluster over, and all the bulbs twist out, replace the same way you took out

Feb 06, 2010 | 2005 Buick LeSabre

1 Answer

Need to change out dash light bulb on a 1993


you will have to remove the dash panel around the cluster to get the cluster out. should be held in place with a couple of philips screws and some 7mm or 1/4in bolts remove these and the panel should pop loose will have to disconnect the switchs mounted in the panel. the speedo cluster is next and is bolted in place. you will probably have to work around the steering wheel and column. make sure to unplug speedo and if shift indicator on dash careful not to break it.

Aug 26, 2009 | 1993 Mercury Tracer

1 Answer

98 merc tracer wont turn over....please helpme...


when tracers stop out of the blue like this, it can be a number of things. #1 is fuel pump failure or pump relay, or fuse. check to see if there is perssure at fule rail. check fule pressure regulator. #2 is ignition coil failure, or no spark. check plug wire from coil for spark. that will get you going in right direction. good luck.

Jul 12, 2009 | 1998 Mercury Tracer

2 Answers

98 Mercury Tracer idle drops at a dead stop and continues to run rough at normal driving speeds. Freeway or in town. Changed plugs / wires/ fuel filter and IAC motor. No changes in performance. Any...


Could be either the ignition coil or an injector problem whereby the latter could be caused by impending failure of the on-board computer.
Check with any chain parts store in your area by phone and ask if they offer a free code check for your car.
Even without a check engine light, you may have a code (or more) stored in the ECU. 

Mar 17, 2009 | 1998 Mercury Tracer

1 Answer

Light bulb number 1992 Tracer


The bulb number is A12V10W (12 Volts, 10 Watts). The easiest thing to do is to visit an automotive parts store as they usually have a bulb replacement manual which will list most of the bulbs based on the make, model, and year of your vehicle. The other alternative is to visit the link below and input the aforementioned data (I am not sure if the number that you will find on the website will be universal or only a Sylvania part number) http://www.sylvania.com/ConsumerProducts/AutomotiveLighting/LampReplacementGuide/

Nov 23, 2008 | 1992 Mercury Tracer

1 Answer

Rear tail light


white with tan tracer....brake lights
light green...left turn
tan ....right turn
black with yellow tracer....tail lamp
violet with black tracer....backup lamps

as far as the bulb not lighting it could be either the socket or the circuit board

Nov 02, 2008 | 1999 Dodge Durango

1 Answer

1993 mercury tracer


To replace the headlight on a 1993 Tracer you must turn the black plastic retainer ring counter clockwise and then pull back gently. The ring and bulb should then slide out toward the engine.
Carefully grab the sides of the plug and pull the bulb out.
When replacing the bulb make sure not to touch the glass part or it will cause the bulb to burn out sooner. Place the black ring back over the bulb with the open end towards the glass part of the bulb. Fit the wiring onto the back of the bulb and insert the bulb back into the reflector. The black plastic ring has notches that fit over protrusions. Turn the black ring clockwise and your done. Test the headlight. Happy Driving

Oct 08, 2008 | 1993 Mercury Tracer

Not finding what you are looking for?
1998 Mercury Tracer Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...