Question about 1993 Isuzu Trooper

1 Answer

I have changed everything: Spark plugs, Wires, Coil Packs, Ignition Control Module, Air Idle Control Valve, Throttle Position Sensor, Map Sensor, Cleaned out my PCV valve. My EGR Valve is in great shape so there is no need to replace my O2 Sensors. It is still running rich and turns off. HELP ME PLEASE BEFORE I GO NUTS

Posted by on

  • Anonymous Mar 15, 2014

    It started with throwing codes p304,p305,p306.Misfire. then it threw p1152running rich and lean, and last but not least p1504 and p1506 runs great but idles rough.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 772 Answers

There are three components that will enrich the fuel mix: 1)engine coolant temperature sensor. If this is not working or the signal is interrupted by a wire breakage then the engine will run rich. The coolant sensor informs the ECU (high resistance) that the engine is cold at start up and so the ECU responds by increasing the fuel injection cycle to enrich the fuel air mix. Later on as the engine warms the resistance of the coolant sensor drops and the injection cycle is reduced by the ECU. If the sensor is faulty or has become disconnected (wire break or corrosion of the socket pins) the ECU assumes that the engine remains 'cold' and the engine runs permanently rich. 2) O2 sensor, operates completely independently of the EGR, if it is faulty and signals 'too much oxygen' then the ECU will significantly enrich the fuel mix to try and balance what it thinks is an excess of air. 3) Fuel pressure regulator. If the diaphragm has broken or there is a leak in the vacuum line this will result in higher than needed fuel pressure in the fuel rail at idle. The vacuum line acts against the spring pressure holding the valve closed. At idle, the inlet vacuum pulls back on the diaphragm reducing the fuel pressure required to open the valve. Low fuel pressure coupled with short duration injection times will mean a lean mix at idle. If the vacuum is compromised or the diaphragm damaged then the increase in rail pressure will make the fuel mix very rich to point of flooding the engine

Posted on Nov 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an issue with my 1995 Toyota Tercel DX with a 1.5liter engine. I have replaced everything from crankshaft position sensor, camshaft position sensor,coolant temperature sensor, Throttle position...


A lot of things have been replaced ... but there was no mention of checking any fuses or relays.
As an example ... if the fuel pump relay is bad then the car will crank over but not start

Jan 21, 2018 | Toyota Cars & Trucks

1 Answer

What does error codes 40 and 41 mean on my 1999 mitsubishi eclispe mean


11 Oxygen sensor fault.
12 Airflow sensor fault.
13 Intake air temp sensor fault.
14 Throttle position sensor (TPS) fault.
15 Idle speed control (ISC) motor position sensor fault.
21 Coolant temp sensor fault.
22 Crankshaft position (CKP) sesnor fault.
23 Camshaft position (CMP) sensor fault.
24 Vehicle speed sensor (VSS) fault.
25 Barometric (BARO) pressure sensor fault.
31 Knock sensor fault.
32 MAP sensor faulty.
36 Ignition timing adjustment signal fault.
39 Oxygen (O2) sensor fault.
41 Injector(s) fault
42 Fuel pump fault.
43 EGR fault.
44 Ignition coil (cylinders #1 & #4) fault.
52 Ignition coil (cylinders #2 & #5) fault.
53 Ignition coil (cylinders #3 & #6) fault.
55 Idle air control (IAC) valve position sensor fault.
59 Rear Oxygen (O2) sesnor fault.
61 Transaxle control module torque reduction signal fault.
62 Variable Induction control (VIC) valve position sensor fault.
71 Traction control (TC) vacuum valve solenoid fault.
72 Traction Control (TC) vent valve solenoid fault.

Sep 26, 2014 | 1999 Mitsubishi Eclipse

1 Answer

Rough ideal after warm up have new map, maf coolant sensor wires, plugs and coil packs. no coolant leaks, no vacuum leaks. fuel pressure OK. runs great except for ideal cam sensor OK compression OK. Even...


Try the tps, throttle position sensor, and the idacv, idle air control valve. Even sometimes the temp sensor could be bad, telling the motor its cold when its really hot..

Oct 08, 2017 | 1999 Chevrolet Lumina

2 Answers

98 Pontiac GRAND am


The plugs and crank sensor could have done it, but the TPS and idle air control would have nothing to do with a random miss.
A more likely cause is the ignition module or a fuel problem. You may have to wait until the problem is bad enough to kill the engine or you have more codes to check out.

May 20, 2013 | Cars & Trucks

1 Answer

2.2 litre 1995 gmc sonoma idles rough no trouble code. found hole i brake booster vaccum line fixed that. replaced and changed fuel filter, idle air control valve, got spark at coil packs, put new spark...


Three things you should check using a good code checker which can read sensor outputs - the throttle position sensor (TPS), the mass air flow sensor (MAF) and the EGR valve. While you are at it, replace the PCV valve.

Jul 30, 2017 | 1993 GMC Sonoma Club

1 Answer

My x type 3.0 has fault readingP1647 could you tell me what this means please


OBDII DTC

P1001 Key on engine running unable to complete; key on engine running aborted

P1100 Mass air flow sensor intermittent

P1101 Mass air flow sensor out of self test range

P1104 Mass Airflow (MAF) Sensor Ground Circuit Malfunction

P1107 Left MAP Sensor Circuit

P1108 Right MAP Sensor Circuit

P1112 IATS Circuit High Voltage

P1113 IATS Circuit Low Voltage

P1121 Pedal Position Sensor Circuit A Range/Performance

P1122 Pedal Position Sensor Circuit A Low Voltage

P1123 Pedal Position Sensor Circuit A High Voltage

P1137 No Rear HO2S Response

P1138 No Rear HO3S Response

P1157 No Rear HO2S Response

P1158 No Rear HO3S Response

P1171 All Cylinders Too Lean

P1172 All Cylinders Too Rich

P1176 Adaptive Fuel Metering Trim Too Lean

P1177 Adaptive Fuel Metering Trim Too Rich

P1178 Adaptive Fuel Metering Trim Too Lean

P1179 Adaptive Fuel Metering Trim Too Rich

P1187 Both Front HO2S Heater Circuits (High Resistance)

P1188 Both Front HO2S Heater Circuits (Open Short to Ground High Resistance)

P1190 Both Front HO2S Heater Circuits (High Battery Voltage Short to Voltage)

P1193 Both Front HO2S Heater Circuits (High Resistance MAF Sensor Fault)

P1194 Both Front HO2S Heater Circuits (Open Short to Ground High Resistance)

P1196 Both Front HO2S Heater Circuits (High Battery Voltage Short to Ground)

P1198 Fuel Level Sensor (High Voltage)

P1199 Fuel Level Sensor (Low Voltage)

P1201 No. 1 Fuel Injector

P1202 No. 2 Fuel Injector

P1203 No. 3 Fuel Injector

P1204 No. 4 Fuel Injector

P1205 No. 5 Fuel Injector

P1206 No. 6 Fuel Injector

P1221 Pedal Position Sensor Circuit B Range/Performance

P1222 Pedal Position Sensor Circuit B Low Voltage

P1223 Pedal Position Sensor Circuit B High Voltage

P1224 Electronic Throttle Control Position Error

P1226 Mechanical Guard Circuit Range Performance

P1227 Mechanical Guard Circuit Low Input

P1228 Mechanical Guard Circuit High Input

P1229 Throttle Control Circuit Malfunction

P1230 Fuel Pump Relay Malfunction

P1235 VSV 1 Circuit Range/Performance

P1236 VSV 1 Vacuum Circuit Failure

P1237 VSV 2 Atmosphere Circuit Failure

P1238 VSV 3 Release Circuit Failure

P1240 Throttle Position Sensor Voltage Malfunction//Sensor Reference Voltage Low (Throttle

Fuel Tank Pressure)

P1241 Throttle Position Sensor Voltage Low Input//Reference Voltage Low (Throttle Fuel

Tank Pressure)

P1242 Throttle Position Sensor Voltage High Input

P1243 Throttle Position Sensor Ground Malfunction

P1245 Crank Signal Low Input

P1246 Crank Signal High Input

P1313 Misfire Catalyst Damage Bank No. 1

P1314 Misfire Catalyst Damage Bank No. 2

P1315 Misfire Excess Emissions

P1316 Misfire Rate Above Limit

P1335 Crankshaft Position Sensor Circuit

P1336 Camshaft Position Sensor (CMP) Circuit Performance

P1361 Ignition Coil Primary Circuit (Cylinder No. 1)

P1362 Ignition Coil Primary Circuit (Cylinder No. 2)

P1363 Ignition Coil Primary Circuit (Cylinder No. 3)

P1364 Ignition Coil Primary Circuit (Cylinder No. 4)

P1365 Ignition Coil Primary Circuit (Cylinder No. 5)

P1366 Ignition Coil Primary Circuit (Cylinder No. 6)

P1367 Ignition Monitor (Bank A)//Ignition System Failure Group 1

P1368 Ignition Monitor (Bank B)//Ignition System Failure Group 2

P1371 Early Activation Ignition Coil (Cylinder No. 1)

P1372 Early Activation Ignition Coil (Cylinder No. 2)

P1373 Early Activation Ignition Coil (Cylinder No. 3)

P1374 Early Activation Ignition Coil (Cylinder No. 4)

P1375 Early Activation Ignition Coil (Cylinder No. 5)

P1376 Early Activation Ignition Coil (Cylinder No. 6)

P1392 Variable Valve Timing Solenoid A Low Input

P1393 Variable Valve Timing Solenoid A High Input

P1396 Variable Valve Timing Solenoid B Malfunction

P1397 Variable Valve Timing Solenoid B Low Input

P1398 Variable Valve Timing Solenoid B High Input

P1400 EGR Valve Position Circuit (Valve Sticking Open or Short)

P1401 EGR Valve Position Circuit (Open Short to Ground)

P1408 EGR Temperature Sensor Circuit

P1409 EGR Valve Circuit

P1440 EVAP Purge Valve Open

P1441 EVAP Valve Circuit

P1443 EVAP Valve Circuit

P1447 EVAP Valve Circuit

P1448 EVAP Valve Circuit

P1454 EVAP System

P1474 Charge Air Coolant Pump Relay

P1475 Radiator Fans Slow Malfunction

P1476 Radiator Fans Fast Parallel Circuit Malfunction

P1506 Idle Speed Control Circuit (Low RPM; Bank B)

P1507 Idle Speed Control Circuit (High RPM; Bank B)

P1508 Idle Speed Control Circuit

P1509 Idle Speed Control Circuit

P1512 Throttle Position Sensor Idle Switch Sense Circuit

P1513 Throttle Position Sensor Idle Switch Sense Circuit

P1514 Park/Neutral Position Switch High Load Neutral/Drive

P1516 Gear Change Park/Neutral Malfunction

P1517 Engine Cranking Park/Neutral Malfunction

P1607 MIL Output Circuit

P1608 Automatic Transmission

P1609 Internal ECM Error

P1641 Fuel Pump Relay No. 1

P1646 Fuel Pump Relay No. 2

P1739 Automatic Transmission

P1775 Transmission Control Module MIL Circuit

P1776 Torque Reduction Request Signal

P1777 Torque Reduction Circuit

P1780 Automatic Transmission

P1781 Automatic Transmission

P1782 Automatic Transmission

P1783 Automatic Transmission

P1785 Automatic Transmission

P1790 Automatic Transmission

P1791 Automatic Transmission

P1792 Automatic Transmission
P1794 Automatic Transmission

Mar 22, 2013 | Jaguar Cars & Trucks

2 Answers

41 thrt val sol


P0041 Oxygen Sensor Signals Swapped Bank 1 Sensor 2/Bank 2 Sensor 2
looks like your wires and melted together or a rodent has chewed them

Feb 10, 2012 | Mitsubishi Montero Cars & Trucks

1 Answer

My '01 impala 3.4 v-6 flat spots when COLD, at around 20mph. the idle is ruff with random misfires. acceleration is overall poor. when HOT, most symptoms go away leaving only some slight acceleration...


depending on mileage, but possible tune-up could fix it. if already done then check ignition coil pack and ignition wires also spark plugs, check vacuum hoses for leaks or porous, last injectors clogged - use some techron fuel injector cleaner (wal-mart has them). Also get the throttle body and iac valve cleaned by throttle cleaner . Also this other possibilities are to be checked and confirmed.:---- Engine running rough or misfiring can be cause by the following:

1.Defective spark plugs
2.Inadequate spark/coil, defective spark plug wire.
3. Lack of compression
4.False air leakage.
5. Faulty fuel injectors.
6. Insufficient fuel pressure.
7. Contaminated fuel.
8. EGR valve that is leaking.
9. Oxygen sensors.
10. Throttle position sensor.
11. Manifold absolute pressure sensor
12.Mass Airflow Sensor
13.Idle air control valve

--------- This should help.Keep updated.Thanks.Helpmech.

Mar 27, 2011 | 2001 Chevrolet Impala

1 Answer

Vehicle runs rough and seems to be flooded


Assuming it has a 3.1 V-6, it could be any # of failures. Bad plug wires, ignition coils, control module (under coil packs), crankshaft position sensor, map sensor, throttle position sensor, egr valve, fuel pressure regulator, fuel injectors, engine coolant temperature sensor, vacuum leaks; have it scanned for trouble codes to help in diagnosing! If you think it is just over fueling (flooding),look at fuel pressure regulator or coolant temp sensor ( when they fail the computer thinks its always -40 F causing it to over fuel). A bad map sensor can cause the same. Hope this helps. Thanks in advance for rating me!

Jan 22, 2009 | 1993 Oldsmobile Cutlass Supreme

2 Answers

1999 Ford Taurus mechanical problem


Hello,
your problem appears to be the idle control motor located on the air intake manifold it is a small motor that goes bad quite often. Other items that can cause this is a bad /clogged air filter or a tune up (spark plugs and wires), or clogged fuel injectors. to clean the injectors you can buy a container of fuel system cleaner and pour it into the gas tank and as you drive it cleans the system.

Once the fuel system is cleaned via a tankful of cleaner & gas then the idle controller motor would be next on the list to be replaced.

Good Luck !
Rich Lilja

Dec 03, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
1993 Isuzu Trooper Logo

618 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...