Question about 1989 Nissan Hardbody King

1 Answer

Instructions how to remove door panel on a 1993 nissan truck

Are there any special tools or instructions in how to remove and install the drivers door panel? the outside doo opener does not engage or work.
thank you.
Irving Texas

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hey juan...if you're not familiar w/ it, which seems evident, its good that ya didnt tear into it anyways. is it fixed yet? it should be by now! eric dude

Posted on Oct 08, 2008

  • LaBeauA11 Oct 08, 2008

    but seriously, you can get a window crank tool at any auto parts store, along with a #2 philips screwdriver, & a door panel clip removal tool, remove the armrest, (two screws underneath) perhaps covered by plastic plugs..Remove the window regulator crank, (if it doesn't have power windows), then use your panel clip tool to carefully disconnect the plug-like clips that encircle the doorpanel.

    Chances are, your handle linkage has undone itself .....hope it helps! eric dude



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I remove the rear sliding door interior panel on 2001 Nissan Quest?

Mostly clips, screws hold the handle on and bezel around it has clips that can carefully be pried off.. A door panel tool should be used to enage and pry panel clips off

Aug 22, 2014 | 2001 Nissan Quest

1 Answer

How to removed drivers side door panel on 2008 xterra

There's usually always screw hidden in door handle, then remove any other screws in panel,remove any trim then panel pops off around edges. Their is a special tool for this. Harbor Freight or Auto Zone.

Nov 15, 2012 | 2008 Nissan Xterra S

1 Answer

I have 1993 Camaro Z28 Coupe, how do I fix the window on driver's side from sticking in the down position.

Replace the window motor. They cost around $100 for the part and $150 for the labor. If your handy with tools you can do it yourself. Just remove the door panel. Drill out the rivets holding the motor inplace. Remove the motor and install the new motor with bolts to replace the rivets (included in the package) and install the door panel.

Feb 12, 2011 | 1993 Chevrolet Camaro

1 Answer

How do I remove the interior door panel on a 93

remove screw and bolts holding your trimboards to its door panel using screw drivers covered its tip with masking tape to avoid damaging the trimboards upholstery and simply lift off the trim panel which light in construction.

Apr 07, 2010 | 1993 Nissan Pathfinder

1 Answer

The rear drivers side door will not open...thr handle doesnt seem to be gripping anything its just loose..

Control rob dislodged from attachment points. Remove door panel with special tools available at local auto parts store. They will advise on type and procedure to remove door panel for access to door mechanism. Replace rod to proper attachment location.

Jul 07, 2009 | 1999 Nissan Pathfinder

1 Answer

1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Mar 20, 2009 | 1990 Nissan Maxima

1 Answer

Need to change CV Joints.

Not bad hardest part is removing nut on hub after removing tire. large socket for that nut may be required.

Mar 17, 2009 | 1993 Nissan Quest

1 Answer

Remove driver's side door panel on 2002 nissan altima

Removal instructions are available with images and step by step directions,

Nov 13, 2008 | 2002 Nissan Sentra

1 Answer

1993 nissan maxima drivers door lock cylinder

you have made a boo boo somewhere,are you a certified city and guilds technician,if not then you shouldnt be repairing customers cars

Oct 31, 2008 | 1993 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

865 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77932 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides