Question about 1994 Toyota Camry

1 Answer

Another problem. On this same toyota camry I am having trouble with the outside CV boot on the passenger side getting torn up. I replaced both drive shafts this past late winter which were rebuilds and am still having the same problem. Any ideas as to what is causing them to tear up?

Posted by on

  • butchie74 Jul 01, 2008

    Scott,

    I was told that the motor mounts are probably the problem. I checked them and sure enough they are worn. I think they allow the engine to flex more than normal and that puts more stress on the boots. Thanks for the reply though.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

May just be of poor quality or there is something making contact while turning.
Jack axle up not frame support with jack stands, spin wheel and turn steering wheel while inspecting for rubbing.

Posted on Jun 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1994 toyota camry v6 and im tryinh to remove the inner drive axle out so i can get to the seal where the transmission fliuld is coming out and i have already removed the outer drive axle with the...


Is this the passenger side? Remove the three bolts that hold the bracket that the shaft goes thru to the block. Pry the bracket from the block slightly and tap the shaft and bracket from the trans.

Aug 11, 2010 | 1994 Toyota Camry

1 Answer

Can the boot that is torn be replaced on a CMB axle or is it called CV axle? or does the whole thing need to be replaced?


the boot can be replaced, but you have to dissassemble the joint to install it, check the balls and surfaces for any sign of wear or pitting, and use all the grease from the kit

May 06, 2010 | 1989 Toyota Camry

1 Answer

'93 Isuzu Rodeo, CV Joint replacement.


unbolt the tie rod end and the lower a arm and it should slide out of there

Jan 26, 2010 | 1999 Isuzu Rodeo

1 Answer

I need to change the front right CV DRIVE SHAFT of my 2002 Toyota Camry.


Cheaper to find a complete assy at a salvage yard. To replace the axle unless you are handy with tools would recommend buy the axel and take it to a repair shop.
To check the CV joint do a visual inspection, they normally have a torn boot and dirt in the joints and causes them to fail. Also to check it drive the car it will make a bumping noise when you turn hard either direction

Nov 13, 2009 | 2002 Toyota Camry

1 Answer

My outer cv boots are torn on both sides.


He is quite right in what he says but he's way over the top in price Get some more quotes Suspension shops good place to go and no your wheels won't fall off but you'll end up having to replace your cv joints which will cost. ie: new boots = $ 30 ea cv joints $200 ea

Oct 22, 2009 | 2000 Nissan Maxima

1 Answer

No grease on c v shaft


is your cv shaft boot alright.hope its not torn.you can put grease in but you have to take the cv out of the car,undo the clips on boots fill some cv grease and put the clip back on and back on your car

Oct 10, 2009 | 1994 Toyota Camry

1 Answer

Needed to replace both CV joints on a 95 Camry. Passenger side would not come loose. The CV joint comes all in one piece, although my step Dad seemed to think that it could have been pressed into the...


circlip in back of cv on the end of the shaft ,cut boot away and look inside on end of shaft their should be a cut away on cv and that is the access to get the circlip loose whilst you wack the cv with a mallet

Jan 18, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...