Question about 2001 BMW Z3

1 Answer

I am geting an error EEP_1 when the car is cold solution?

I continue to get an error EEP_1 when the car is cold solution?

Posted by on

  • Anonymous Jul 17, 2008

    My 2000 BMW Z3 HAS AN ERROR EEP_3 AND GAGES DO NOT WORK AFTER BEING PARKED IN THE GARAGE. AFTER BEING PARKED IN THE SUN FOR A FEW HOURS THE ERROR GOES AWAY AND THE GAGES WORK.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • BMW Master
  • 1,224 Answers

Starter ignition relay froze shut replace accordingly
i had the same problem with my 528i 1978 vintage
at the time i didnt have the money for the relay so i put a manual start on it and ran inside vehicle till i could replace the ignition relay put key in turned to on and hit the starter and i was 3000 miles away from home i had to crawl under vehicle to get this put on but worth it at the time

Posted on Jun 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Not geting all my gears


first, make sure the linkage at the transaxle is ok. then, loosen the clamp on the shifter shaft near the exhaust downpipe.

Dec 31, 2013 | 1989 Volkswagen Golf

1 Answer

Turning the temperature knob all the way hot, air coming out goes cold. Turn the knob all the way cold and it goes hot for a minute and then cold.


MAYTEX INSIDE THE CAR GONE IF YOU GO ON U TUBE AND PUT IN temperature IN CAR NOT GETING HOT YOU CAN SEE IT ON THAT

Oct 04, 2013 | Jeep Cars & Trucks

1 Answer

1998 ford windstar ac not blowing out front vent


i found lose vacuum line and started geting cold air front was working until my car start staling and check engine light came on car turn off code po172 ....some were is

May 23, 2012 | 1998 Ford Windstar

1 Answer

When i start the car it drives ok but after warming up a bit the car loses acceleration and starts to boggle?


check for a bad fuel pump relay. it maybe geting hot and shutting down. it may be a bad coolant tempurature sensor also, that sends info to ecm.The engine will think it was still cold, even though it was not, causing all kinds of things to run draggy. thats why it runs ok when its cold. it sends wrong info to computer. thinking its cold, when in reality its warm. have a good day !!

Mar 19, 2011 | 1996 Ford Probe

1 Answer

1990 f150 302 new motor has progreesivly go worse when trying to start it takes a wile the fuel pump in both tank are working has new spark plugs at overhaul but no other new ignition parts seems to notbe...


maybe fuel enrichment circuit for cold start is not working. If you spray some starting fluid in the throttle body and it starts right up cold, look for a problem with fuel enrcihment during cold start.

Feb 24, 2010 | 1990 Ford F150

1 Answer

I just bought a ford f250 and its geting cold where do i find the plug to keep the glow plugs warm and how cold does it need to b before i plug it in


if it has a block heater the plug should be on passenger side under bumper tucked up buy radiator not all come with block heater

Dec 05, 2009 | 2000 Ford F250 Super Duty Crew Cabs

2 Answers

How do I fix a P0301 code for a 02 taurus


Trouble Code: P0301

Cylinder Number 1 Misfire Detected
Possible Causes:


Air leak in the intake manifold, or in the EGR or PCM system Base engine mechanical problem that affects only Cylinder 1 Fuel delivery component problem that affects only Cylinder 1 (i.e., a contaminated, dirty or sticking fuel injector) Ignition system problem (coil, plug) that affects only Cylinder 1

May 28, 2009 | 2002 Ford Taurus

1 Answer

93 ford explorer xlt


First check your 4 wheel drive switch to make sure it works, for on an off settings. (Use a volt-ohm meter for this. On should show continuity in the readings (if digital then it should show zeros in the dial) Off should show no continuity or 1.0 in the dial.

1. Check your fuses.
2, IF OK, then check your FUSE LINKS.
3. IF OK, then check your 4 Wheel Drive relay in the fuse box.
4. IF OK, then check continuity of the wires harness to the 4 wheel drive switch for DC voltage.

Jul 26, 2008 | 1994 Ford Explorer Limited

Not finding what you are looking for?
2001 BMW Z3 Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...