Question about 1999 Isuzu Rodeo

3 Answers

Obd code 1627 ,1999 4 cylinder isuzu rodeo

I have a problem with this 1627 code,I drive the car and clear the code and the monitors.But once the obd connector is hooked up at the smog shop ,it trips the code and the gas light flashes and the gas gage goes back and forth.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hprice is right. when you get this code it's usually because the little "fingers" that slide against the metal potentiometer bar on the fuel guage sensor has gone bad or broken off, or in some cases just pushed away from the slider due to it's natural wiggling.

that sensor is located in the fuel pump and you can't really buy a replacement sensor so instead you get the new fuel pump.

I went to 3 yards for this car and almost all the rodeo's of this year had the fuel tanks removed and the fuel pump / sensor pulled. so you can save a hassle and just buy a new pump.

removal is tricky because you've got bolted to the tank the lines that go up, so you have to be careful about removing them. Plus getting that back into the tank is tricky as it has to be exactly straight up / down then the ring clips it down.

It was a long job but had to be done to get past inspection because the check engine light can fail inspections. even if it has nothing to do with smog.

Posted on Dec 14, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

P1627: [driver "1" input high voltage]...

I believe the PCM was expecting a signal from a sensor (which one I don't know) that should be low voltage and instead was high voltage and therefore triggered a DTC for that sensor...I will guess a bad O2 sensor...

code may also be cleared by disconnecting battery negative wire for 30 seconds...remember to reset your clock and radio settings...

sorry that is all I can find...please rate me solved

Posted on Jun 27, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fuel level sending device gone bad... tank removal is neccesary.

Posted on Jul 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Isuzu Rodeo 4 cylinder Check Engine Light


Normally a shop would use a scanner to watch the operation of the EGR valve and sensor.
Code 401 means the sensor is telling the computer the flow is not enough. So the problem could be the sensor rather than the EGR valve. And yes one of the ports could be blocked too.

Jun 28, 2013 | 2001 Isuzu Rodeo

1 Answer

P0300 isuzo rodeo 2.2l


PO300 is a OBD II code for a random multiple cylinder misfire detection. Meaning any one or more than one of the engines cylinders is not firing at different times. Any number of malfunctions can cause this.To determine what repairs are needed, i recommend the engine to be diagnosed with a scantool and oscilloscope to monitor the crank sensor signal and other inputs to the computer.
I hope this information is helpful.

Sep 03, 2011 | 2001 Isuzu Rodeo

1 Answer

Where are the connecters at for checking codes located for a 1997 rodeo with a 3.2 motor and auto trans?


For 1997 Isuzu Truck Rodeo 2WD 3.2L MFI SOHC 6cyl the OBD Diagnostic Link Connector is located: Front seating area, driver side, under dash, mounted above kick panel.

Hope this helps (remembert to rate and comment this answer).

Jul 12, 2011 | 1997 Isuzu Rodeo

1 Answer

I HAVE A 1999 ISUZU RODEO WITH THE OBD TROUBLE CODE P1392 (G SENSOR LOW VOLTAGE). HOW CAN THIS BE FIXED?


that code is not listed on alldata.
a 'G' sensor is related to your anti-lock brakes
first check is ALL the grounds under vehicle.

May 27, 2011 | 1999 Isuzu Rodeo

1 Answer

Wats the code p1000 on my 2002 jaguar x type


P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.

Feb 18, 2011 | 1999 Jaguar XK8

2 Answers

2000 Isuzu Rodeo, 3.2, 112,000 miles, Service Engine Soon light is on, won't pass inspection till I get it cleared off. Hooked up a scan tool the only code is P1340 and it scan tool says it's a...


well clear code and drive it about 50 to 100 miles to try reset the monters and see if light stay out if so go get it smog so the system that could couse this is a bad wireing harness this may be hard for you to diagnosis this system put if you want me to help you can emaile me and i will send you the hole diagnosis chartDTC P1340 ION Sensing Module Cylinder ID Fault (Cylinder Synchronization Fail)

cant do it here to big

Oct 05, 2009 | 2000 Isuzu Rodeo

2 Answers

99 rodeo check engine light is on.


No...the fuel sending unit is not a computer driven item nor is it monitored in any way by the onboard computer system. Interface with scanner and retrieve code(s) associated with indicator lamp occurrance

Sep 27, 2009 | 1999 Isuzu Rodeo

2 Answers

Obd code 1627 ,1999 4 cylinder isuzu rodeo


If P1627 is set when there is a problem with the fuel level sending unit, 100% sure on this problem, replace the fuel level sender in the gas tank, about 2.5 hours, very straight forward job

Jun 02, 2009 | 1999 Isuzu Rodeo

1 Answer

Obd port


OBD ports were mandated to always be on the drivers side near the steering column, on, or under the dashboard.

Jan 23, 2009 | 1995 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

620 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...