Question about Avanti Studebaker

1 Answer

1939 straight 8 main bearings

Hello, I need main bearings for for a 1939 250 C.I. straight 8 Studebaker.
Can you PLEASE Help Me... Thank You Terry Walters TWPS@AOL.COM

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Avanti Master
  • 1,224 Answers

Ok i dont know if these could be manu. or machined but there is one place i know of that could get you machined parts for this era vehicle
would be jay leno's garage or a little place here in arizona i dont know if they have them but they got over 60 acers <<< spell check
of vehicles from old to new
call matt hoctor tell them shaggy refered you
phoenix number 602-252-2122
maricopa 520-568-2945
fax 602-258-0951
hidden valley auto parts
Email Hvap@aol.com
21046 n. rio bravo rd. maricopa az. 85239
im sure this parts yard will have what your looking for and at a good price i wish i could help further in helping this is where i would start
http://hiddenvalleyautoparts.com/

Posted on Jun 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello i need help desperately my car do not pass the smog, i have PO113 and PO115, also my car runs with OBDII scan tool plugged in only, but this codes come only if i unplug the scanner, other than that...


My question is it a Studebaker or a Lamborghini? You want an answer give relevant information! Always remember that when you ask a question That no one can read you'll mind!!!!
More information please!

Mar 03, 2015 | Cars & Trucks

1 Answer

I have a 1939 Chevy ,model # 9JB Solid straight axle


check the tie rod end bearings as one be faulty. Check for worn out king pin bushes.or worn out king pin thrust bearings.

Dec 16, 2014 | Cars & Trucks

1 Answer

I am trying to replace the passenger side hub and bearing,before i tear it down i need to know if the bearing is just pressed onto the new hub and then the whole assembly slides onto the splined end of the...


Hello texasjagfan: My name is Roger and I will help you. The front hub bearings are press out bearings and you will need a press in order to change them. You will need to remove the front spindle to gain access to the bearings.You also will need an alignment when finished replacing the front bearings. The rear bearings are a hub and bearing unit.
Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Aug 18, 2011 | 2003 Chrysler PT Cruiser

1 Answer

Replace rear main seal


Hello phjette: My name is Roger and I will help you. Whether you have a 4.0 6cyl. engine or the 5.2 V-8 engine. to replace the rear main seal will require the removal of the oil pan. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Apr 19, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

Mar 02, 2011 | 1989 Honda Civic

1 Answer

Need the crankshaft main bearing torque specs and connecting rods 2001 chrysler sebring convertable 2.7


Hello tlittle3: My name is Roger and I will help you.See the attached image. Be sure to follow steps as it is very inportant. You will notice that you need to index some of the bolts. That is merely turning the bolt a specified degree. The crankshaft tie bolts are the bolts that are in the side of the block. install horizontal. Shold you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Rogera32a1ae.jpg

Apr 26, 2010 | 2001 Chrysler Sebring

1 Answer

F250 Diesel will not start cold . Has power to glow plugs for short time ,but will not start 1986 modle.


Hello philkatkiele: My name is Roger and I will help you. First thing you need to check is the glow plugs. They will need tested individually. Un plug all 8 glow plugs. Take a test light and hook end to the positive battery cable. Touch opposite end of test light to the terminal end of the glow plug. The test light should light. Touch all 8 glow plugs. Ant that do not light are bad and will need replaced. If glow plugs are burnt out then the controller will flash wait light to early or very fast. The wait light should be on for approximately 10 seconds.If al glow plugs check ok then I would suspect the glow plug controller as the problem. Also if the temperature out side is below 40 degrees the truck should be plugged in. This will help to make the engine start easier. Should you need further help please just ask.Please rate the answer as this way I know it was helpful. Thank You for using Fix Ya. Roger

Feb 15, 2010 | 1986 Ford F 250

1 Answer

What is the points gap on a 1950 Studebaker Champion. Car is a convertable.


Hello taemoore: My name is Roger and I can help you. Should use champion plug J7 Plug gap is .025. Point gap is .020. Fire order is 1-5-3-6-2-4. Should you need further help please just ask. Please rate the answer. This way I know it was helpful. Thank You for using Fix Ya. Roger

Feb 10, 2010 | 1965 Ford Mustang

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Avanti Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Avanti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...