Question about 1996 Toyota Camry

1 Answer

96 toyota 2.2

Changing timing belt cant get crank pullys off is bolt threaded backwards? and how are the crank and cam alined? thanks for any help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

When i deal with very tie bolts at crakc pulleys, i loose it with an air gun or i install a big bracker bar with a socket and let it contact the car body, and cranck engine just a little be to loose the bolt, just make sure then engine turns to rigth before trying the last sujestion,
and just mark the pulleys with some liquid paper in order to install new belt ar see the alinging marks at autozone.com

Posted on Jun 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

1997 corolla crank pully bolt thread (left hand thread?)


it will be a normal RH thread. For easy removal use a 1/2 drive rattle gun and you will not have to try and hold the crank while you are undoing the bolt.

Apr 04, 2014 | Toyota Corolla Cars & Trucks

1 Answer

Set camshaft timing


there should be marks on crank pully and cam belt pully. rotate motor until crank pully timing mark is on zero.the cam belt pully should be lined up with its own mark.number one piston should be at the top of its stroke (top dead centre TDC) and number one valves should be shut. if the cam belt mark is not alined with its own mark remove the belt realine the marks and refit the belt

Sep 15, 2013 | 1993 Subaru Legacy

1 Answer

I am trying to replace the timing belt on a 95 camry. and cant seem to get the bolt out of the crank pully. Is it a lefthand thread bolt. Or is ther a trick to getting it loose. thanks


If you dont have a impact gun,heres a trick,first,see if the crank goes clock wise direction,if it does,put the socket whit a long brackerbar in a way that will hold it self,then crank the engine whit the starter,whit the ignition key.

Sep 29, 2010 | 1995 Toyota Camry

1 Answer

I'm in the middle of removing the head cylinder on a 95 toyota previa and I'm having trouble trying to get the chain out from the cam gear!is there a way of getting it off without having to take off the...


Dont remove the cam gear until you remove the crank shaft bolt.If you turn the crank with out the cam gear in place you may bend some valves.And damage the head,or a piston as well.
You can use a bar, and a socket on the crank bolt, if it clears everthing and rests on the frame work,then engauge the starter,this will loosen the crank bolt,but dont start the engine.Just a few hits on the key.Stand clear of the bar,!You may have to heat the bolt head a bit,as well.The bolt may have had locktite installed on the threads.Have the battery fully charged.

Sep 13, 2010 | Toyota Previa Cars & Trucks

1 Answer

Need to change timming belt 1997 geo tracker


TIMING BELT CHANGE You should have some mechanical skills before attempting any engine maintenance! These are basic instructions, and you must knoe what you removed, when, and what order so you can reinstall them in order. First, you have to remove everything in the way! You need to remove the Fan, clutch, and shroud, pump pully & drive belts. Next, you need to remove the Crank Pully:

1. Crank Pully Bolt 2. Crank Pully 3. Center Bolt 4. 5mm Hex drive (used to remove pully bolts) Once the fan stuff, and pully(s) are removed, then you need to remove the Timing Belt cover:

Once the cover is removed, you will need to loosen the adjusting nut and pully bolt on the Belt Tensioner:
A. Adjust Nut B. Pully Bolt C. TENSIONER PULLY Once the the Adjust Nut, and Pully bolt are loose, move the pully as far towards the water pump as possible.
Then, you can slip the timing belt from the sprockets. Check the tensioner for roughness and excess play! DO NOT MOVE THE CAM OR CRANK SPROCKETS! IF you do, then you will have to line up the Crank and Cam for piston number one at Top Dead Center before placing the new timing belt on! Note the timing marks on the crank and camshaft sprockets. IF YOU MUST! Allign the Cam and Crank at piston#1, Top Dead Center before removing the belt. Each sprocket has a small hole, with a line through it, and there is a small groove or "V" it alligns with on the engine. Now, once the timing belt is off, look at your new timing belt. Older belts use the Squared off teeth, while new ones have the rounded teeth. Make sure you have the correct belt for your sprockets! Never reinstall a belt that is in questionable condition. BELT WEAR CONDITIONS
If there are Arrows on the belt, they must be pointing to the RIGHT when you put the new belt on the sprockets. If there isn't one, then paint one on, and place the belt back on the sprockets. The arrow will indicate to a mechanic, this is the way the belt must be put back on (if they replace any cam or crank oil seals). Slip the new belt onto the Crank sprocket. While maintaining tension on the side of the belt opposite the tensioner, slip the belt onto the Camshaft sprocket. Releace the Tensioner adjusting nut to allow spring tension against the belt. Temporarily reinstall the crank pully, taking care to align the notch in the pully with the raised area on the sprocket. Rotate the crank clockwise two complete revolutions. Recheck the alignment of the of the valve timing marks. If they do not align properly, loosen the tensioner, slip the belt off the crank pully, align the timing marks, reinstall the belt, and check alignment again. Tighten the tensioner nut, then the bolt. Reinstall all parts removed, in the opposite order, of course. Start the engine and allow to reach normal operating temp, then road test. THEORETICALLY, you should simply be able to replace the belt with the new one, and go, as long as you did not move any of the sprockets when removing or installing the belt. Most people do it this way, and do not test for alignment before replacing everything. When the belt wears, timing will be off, very little, and this is why you check alignment. The belt may have slipped a tooth, making the timing off. This is why the Cam and Crank sprockets must both align properly. An experienced person will do just that: Replace the belt, and go. It really isn't all that hard. It helps to have a second person around with some experience also.

Nov 11, 2009 | 1997 Geo Tracker 2 Door

2 Answers

Fix a cambelt on a freelander


start by removing top front camshaft cover ,revealing camshaft sprockets. now jack veihcul up and place on stands. remove left hand front wheel (cam belt side) . remove power sterring belt and alternater belt.looking at crankshaft pully and using an 18mm socket and bar rotate pully until all three marks line up. crank on 1st timing mark and and cam marks facing each other when all three line up you can then remove crankshaft pully , you will need an impact wrench that can torque up to 300lbs .when pully has been removed you can then remove the lower belt cover you will then see the belt tensioner and unbolt and remove , now place a jack with protection under sump and remove bolts on engine mount, when you have separted the 2 halves of the engine mount you can remove the belt and install new belt , k,series cam holder tool is use full for re-alineing cam marks camshaft marks facing each other and crank line up with raised mark on engine block,it is then a case of putting every thing back inthe same order it came off.there are 2 type of cam belt tensioner you can email me and i will tell you how to do each type. marcusloud@blueyonder.co.uk.

Sep 11, 2009 | 2002 Land Rover Freelander

3 Answers

Having changed the timing belt on my 307 2.0L petrol 2003 how do I re-align the valve timing. I have cam lock tools in place but there is no timing alignment on the crank pully - the pully and crank end...


hi i have a 307 2.0 petrol on a 05 plate how do i time up the bottom end of the engine it has no timming maksand its a free wheeling crank many thanks kev

Aug 21, 2009 | 2005 Peugeot 405

1 Answer

1992 nissan maxima timing belt replacement


need to take off almost every thing from the front of the motor. then take off top half of timing cover.
pull the harmonic balance pully off. then the bottom half of the cover will come off. becareful
the cam gears are hard to aline.
do you no where the knock sencor is located?
if so please email me @ goodedgeworth@gmail.com

Mar 07, 2009 | 1992 Nissan Maxima

2 Answers

Need to set timing on a 88 subaru 1.8 liter


The crank shaft pully will need removal and the water pump pully as well, also the 2 inspection covers and the center housing cover that they conect with, when removed all of the timing belts will be exposed as well as crank shaft end. I used a screw driver angled wedged and held in on the teeth of the fly-wheel to lock it in position so I could remove the crank shaft pully bolt, (standard lefty-loosey threaded). This would have been easier with the fly-wheel locking tool from subaru, or even just a budy to hold the fly-wheel while i turned the bolt loose at the crank pully. I unbolted the fan and slid it out of the way, I did not even need to unplug it. just be sure battery is not conected. The oil dip-stick tube has one 12 mm bolt at the end of a brace at top of engine. loosen and pull up and forward to remove. the crank shaft bolt-you will need to put back in the bolt only! on the end of the crank shaft so you can rotate the engine manualy with a socket on the crank shaft pully nut, while looking through the hole on the top of rear engine area just above fly wheel. wach fly wheel as it turns, look for 3 lines side by side these are not the timing degree marks they are seperate from them, align them to the little arow on the houseing in front of the 3 little marks. be sure the e-brake is set, trany in nutral so engine can turn freely. inspect the cam shaft pullies, on the surface there are 4 evenly spaced holes, there is one tiny hole that lays between the other holes, this little hole that is the pully mark, it needs to be at the twelve oclock position, there is a small groove on the housing at the twelve oclock position as well. align the two with each other, the little hole with the little notch directly above. do the same for the other side cam pully, same way. loosen the idler pulies for each belt, 2 bolts, move it to its full retracted position, pushing on it with fngers against spring tention, titen one of the nuts so the pully stays retracted/pushed. remove old belts, being carefull not to move the place marks of either of the 2 cam shafts or the engine crank placement. put in the new belts check to see if belt has a direction of dravel and match with engine, mine it did not matter but was told that it may with other belt makers? i don't know about that? but thought it was worth the warning?
once belts are on be sure again that marks all mate with marks on all 3 points crank and fly-wheel, both cam shaft pullies with notchs, now release the tnsion on the idler pullies, and retighten where they fell. check again on the 3 timing points be sure they have not moved again... tireing but worth it. if the have moved off of any mark you must realign it by moveing the pully to the rite spot and putting the belt back on. one tooth off on the drivers side of engine cam can meen up to 16 degrees of timing lose either way of perfect. once aligned, put the center cover back over the crank shaft, bolt on. put on the oil dip stick, put on the water pump pully and crank shaft pully, put on belts. leave the fans out untill all is done, just be sure they are free of obstacles so if they come on later it does no harm to it, you, or anything else. leave off the inspection covers at each cam pully. be sure to un block the fly-wheel. re asemble engine and componants to the installed normal positions as best as posible. re conect battery, be sure all tools are clear, start engine, if it will not run smoothly re set the distributer for timing, if still runs bad, you may have one or both cams off by plus or minus 1-2 teeth one the belts. this was hell... you have to move one side one tooth and start the engine and time it again, if that was not it then you move one tooth in in the oposite direction from the oiginal spot, now 2 teeth the oposite way. if not better put back on the original tooth, and do the same to the other cam one step and start at a time untill you find it to work the best, it may even be off by 1 tooth on the rite and 1- tooth on the left. This was a nite-mare but i finaly found the rite placements.
take 2 aspirin, advil, etc. pre-medicate for the manditory headache. and best of luck..
if you are wondering if the valves and the pistons may have struck, forget it subaru made this 1.8l engine as a none contacting engine, this meens that they can never touch piston to valves even in a cam belt failure.

Jul 21, 2008 | 1984 Subaru Gl

Not finding what you are looking for?
1996 Toyota Camry Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...