Question about 2003 Chevrolet Blazer

1 Answer

2003 I look under my 2003 blazer to see how difficult changing the sarter will be. Looks like the power connection and 2 mounting bolts. Is it really that easy?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It's hard but can be done by turning the starter at an angle it will come out.

Posted on Jul 12, 2008

  • ericguthrie Jul 12, 2008

    I've done this two times, it must be turned and brought out at an angle

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i access flare nut frome power steering line under power steering pump


is it really a flare nut? could it be the 'quick connect' type?. if so, search 'quick connect'.

did you look into this?
http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f80caddde

Oct 05, 2015 | 1999 Mercury Mystique

1 Answer

My 99 Chevy s10 blazer is turning over but won't start.. Sometimes all power seems to leave and the dash lights will only flash when I try and start it..starter is fine, battery is brand new, and


It can be your mounting house for your spark plugs how to change it ?how to cheak it ? Well there should be 2 or 3 bolts holding it take the bolts out turn on your truck and remove it like you would if it was a cap in the inside should spin if doesent then thats another problem it wouldn't be your mounting house that will be a snapped little belt in the inside of motor not really sure what's it called. So back to your mounting house disconnect all ur spark plugs only connected to the mounting house ( remember we're they go) then remove the bolts and put the new one

Nov 30, 2012 | 1999 Chevrolet Blazer

1 Answer

Brake pedal in s10 moves side to side, unattached somewhere under dash...how do I disassemble?


at the top of the brake pedal is a mounting bracket that holds the pedal in place,, on that mount, and the pedal, is a bushing that goes bad,, the hold down bolt goes right through it, if this bushing is bad, it will allow the pedal to move slightly from side to side, if however if your pedal has a lot of movement,, you need to check the bracket in total, follow the brake pedal up under the dash,, and check the mounting bolts

Sep 20, 2011 | 2003 Chevrolet Blazer

1 Answer

How do you replace blower motor on a 97 blazer


BLOWER MOTOR IS UNDER THE HOOD MOUNTED THRU THE FIRE WALL ON THE PASSANGER SIDE UNDER THE HOOD HINGE 6 TO 8 LIL BOLTS HOLD IT IN UNPLUG WIRING HARNESS AND DISCONECT GROUND PULL IT OUT CHANGE THE FAN WHEEL LOOKS LIKE AIR FILTER MADE OUT OF PLATISTIC THERE SOME TIMES A CLIP CLIP ON THE SHAFT TO PULL AND USALLY A COUPLE MEDIUM SCREW DRIVERS UNDER WILL POP IT OFF ,, PUT ON YOUR NEW BLOWER MOTOR AND REINSTALL

Mar 02, 2011 | 1997 Chevrolet Blazer

2 Answers

1999 Chevy Blazer Engine will not crank over. All


try turning the key over to the start position. then take a long screwdriver and touch it across the terminals on the starter. this should start your vehicle. if the sarter doesnt turn when you do this,then you have the starter locked up,and yo will have to take it off and install some shims under the bolts.if the starter is trying to turn and the lywheel isnt urning...then you have a locked up engine.

Apr 26, 2010 | 1999 Chevrolet Blazer

2 Answers

Replacing high brake light bulb 2003 blazer


It's mounted up on the roof and held on with a screw on each end. There's a sticky gasket under it to keep the moisture out. Remove the two screws (usually phillips head, but sometimes torx 20 or 25) and persuade it come (peel essentially) off. Pull it out slowly to reveal the plug and unplug it. It's an LED strip so the whole thing will have to be replaced. Easily located on a popular auction based web site for about $50.

Feb 28, 2010 | 2003 Chevrolet Blazer

1 Answer

How do I replace my starter?


Open hood.
Disconnect negative (-) batter cable
Locate the starter (under vehicle).
Remove electrical connections. (be sure to remember/take a picture/ make a drawing/ or mark which wires go to what posts)
Remove mounting bolts.
Remove starter, replace with new starter
Install mounting bolts
Install electrical connections

Jan 06, 2010 | 1990 Chevrolet S-10 Blazer

1 Answer

How do you replace a power steering fluid pump on a 2003 ford escape? It looks like its internal and I may have to pull the motor? please help!


it is directly under the upper engine mount on the passenger side. simply block up the engine from underneath and remove the upper engine mount (5 - 18mm bolts)

Jul 13, 2009 | 2003 Ford Escape

1 Answer

Upper left bell housing bolt removal


2 choises remove motor mounts to lower front of motor to remove from top or lower trans from mount to remove from bottom

Apr 04, 2009 | 1996 Chevrolet Blazer

1 Answer

1986 s10 blazer changing rear view mirrors from


Hi there. The mirrors should have everything you need mounted to them if they are for an s10. There will be three screws on the external faceplate, under that three larger screws that go through the mirror directly to the door.

Mar 15, 2009 | 1986 Chevrolet S-10 Blazer

Not finding what you are looking for?
2003 Chevrolet Blazer Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...