Question about 2000 Ford Expedition

1 Answer

2000 ford expedition fan control only has high speed. Where is the module?

Where is the fan control module to make a repair. Under dash ?

Posted by on

  • Jersey kid Jun 11, 2008

    fan control only has one speed, high.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 324 Answers

It is more than likely your blower motor, the control module only controls the position of the air flow, such as vent, floor defrost......

Posted on Nov 26, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2008 Ford Expedition heater blower stays on high speed no matter where I put the speed button. Have the climate control system.

Sound like the blend door behind the glove box is stuck. My problem that it was stuck in the closed position so I was not getting any heat. I had to take it to the repair shop and they took off the dash to get to it. It was expensive.

Mar 10, 2014 | 2008 Ford Expedition Eddie

1 Answer

2000 ford expedition fan switch does not work on low position only works on high position. is it the switch or is there another control problem?

check resistor under dash by blower motor should be two screws holding it in or goto parts store and get new one and look under dash on passanger side

Nov 13, 2011 | 2000 Ford Expedition

1 Answer

Blower motor only runs on high. other three settings are inop. motor runs okay.

must be the day of fan modules going bad 13th one today. first unplug the fan and get a test lite. using the lite probe the hot side of the plug if it does not lite up on certain positions when you turn the fan speed the fan resistor is bad. di you loose one speed first and then another? if so its defiantly the fan resistor. good luck

Jan 20, 2011 | 2000 Ford Expedition

3 Answers

Keyless entry code location 2000 expedition

Check under the dash below the steering wheel. Mine is on a white sticker with 5 numbers. This is the master code.

Dec 29, 2009 | 2000 Ford Expedition

2 Answers

The heat only comes on at one speed only high

change the blower motor resistor. its located on the airbox under the passenger side of the dash

Nov 13, 2009 | 2000 Pontiac Grand Am GT

1 Answer

2006 ford expedion blower motor only has high speed

Remove the RH lower instrument panel insulator under the dash you should then see it,has one screw holding it to the blower case.It will have OG/BK,LG/WH,YE/RD,BK wires if it is a manual system.If electronic climate control the wire colors will be VT/WH,TN/OG,RD/WH.BK

Feb 17, 2009 | 2006 Ford Expedition

1 Answer


That usually means the circuit board for the fan motor is Burt out big job prob to replace dealer may be.

Jan 22, 2009 | 2003 Ford Expedition

1 Answer

Blower fan runs high only on 2006 Ford Explorer

if you have manual control climate control then the system has a blower motor resistor . if you have automatic climate control then the system has a blower motor speed control. in eather case the part is under the dash in the heater box. depending on the system you have, buy the part and then look under the dash for like part, you will half to remove the under dash panels to be able to see. the part will be on the heater box somewhare.

Jan 21, 2009 | 2006 Ford Explorer

1 Answer

Ac controls quit working blower fan is running on high all thetime. compressor is not working.

fan elays are under hood in black box by battery. 3 of them. 2 for high speed, 1 for low speed. Default is high speed when there is a probem.

Suspect maybe they shorted something out when fixing dent. Did they do any welding on the van? Connecting the cables to the body can sometimes send voltage where it's not wanted.

Nov 06, 2008 | 2000 Nissan Quest

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides