Question about 2006 Nissan Sentra

1 Answer

Drivers door Power Lock

Drivers door locks on its own without touching the power lock button.Other doors do not lock,only the drivers door.

Posted by on

1 Answer

My nissan altima had the same problem, i changed the alternator and it stopped.

Posted on Jul 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming keyless entry to 95 landcruiser


1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button by
itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
indicating successful programming. If the door locks do not cycle, or cycle twice.
repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

Oct 29, 2013 | 2008 Toyota Land Cruiser

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

2 Answers

Drivers side door lock will not lock. Locks are power locks and button works.But door does not lock


the door lock actuator inside the door has gone bad.if the other doors lock and the driver's doesn't then the actuator has gotten too weak to move the lock/ latch.

Aug 13, 2011 | 1995 Ford Explorer

1 Answer

Power door locks, and power side windows wont owrk


check wiring at drivers door hinge inside protectve loom,should find broken wiring

Oct 04, 2009 | 2004 Pontiac Montana

1 Answer

1999 Jeep Cherokee Sport How do you


I WOULD CHECK THE WIRING BETWEEN THE DRIVER'S DOOR AND THE POST..YOU WILL SEE A RUBBER BOOT BETWEEN DOOR POST AND DOOR..HAVE SEEN PARTIALLY BROKEN WIRES CAUSE ALL SORTS OF PROBLEMS HERE

Sep 03, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Drivers Door Lock Problem


Press the passenger side door lock button. if the driver side door unlocks now but wont unlock when you hit the driver side door lock button, it is usually a network communication problem with the B CAN or a faulty Body Control Module.

May 01, 2009 | Honda Accord Cars & Trucks

1 Answer

Honda CRV 2002 Power Door lock


try testing or replaceing the drivers door lock actuator, reprogram ur key fobs and try unlocking and locking ur doors. as far as the lights and reminder,....it sounds like a seperate problem. but try the door actuator first (drivers side always act up and cause every other actuator to act up... like a bad kid that gets the rukkus started and ruins things for everyone..

Apr 01, 2009 | 2002 Honda CR-V

1 Answer

Drivers door power lock wont work.


Either the wring going to that motor or the motor itself is bad.

Mar 08, 2009 | 2000 Toyota 4Runner

1 Answer

All power door locks lock except the driver side front door


On my jetta, if you don't lock the doors with the remote then all doors lock except the drivers door. try this
1. closing all doors walk around to the passenger door.
2.open the door, using the button on the passenger door, lock the doors.

I had this happen to me on my jetta and found you could lock all the doors if you did'nt use the drivers door or you locked using the remote. They did this to keep the driver from locking the keys in the car. I hope this worked for you

Jan 21, 2009 | 1995 Volkswagen Jetta

Not finding what you are looking for?
2006 Nissan Sentra Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...