Question about 1996 Ford F250 Crew Cab

1 Answer

1996 ford f250 4 wheel drive truck

We need a picture of the wheel bearing hub assembly or diagram for this truck to know what parts we need. The original parts were destroyed and we are going to repair it ourselves.

Posted by on

  • Anonymous Mar 13, 2014

    I need a diagram of the automatic front hub assembly for a 1998 Mazda B4000 4X4 to order parts to repair the automatic locking hubs

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

Item Part Number Description 1 N800794-S60 Bolt, M16-2.0 x 50 2 N601797-S2 Bolt, Caliper Mount M12-1.75 x 30 3 2C150 Pin Assembly 4 2C357 Disc Brake Caliper 5 1175 Seal 6 3423 Bearing 7 3105 Front Wheel Spindle 8 4221 Differential Bearing 9 4222 Differential Bearing Cup 10 1190 Wheel Seal 11 1102 Front Disc Brake Hub and Rotor 12 1102 Front Disc Brake Hub and Rotor 13 1197 Locknut 14 1B198 Lockwasher 15 1C245 Thrust Washer 16 35704 Dana Nut 17 2K004 Front Disc Brake Rotor Shield 18 2B292 Anchor Bracket 19 3130,
3131 Steering Knuckle1996 ford f250 4 wheel drive truck - 9572fc0.gif

Posted on Aug 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need a picture of a Front wheel bearing hub assembly or diagram


DUDE, GO TO AUTOZONE.....GET THE SHOP MANUAL...BUY IT, LOOK AT IT.....OR HAVE THE AUTOZONE PEOPLE PRINT YOU A DIAGRAM OF THE FRONT HUB ASSY.

Jul 29, 2014 | 1996 Ford F150 Regular Cab

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

2 Answers

I would like to know if the wheel bearing is in the shaft or the hub?


The Constant Velocity (CV) joints are located on the inner and outer edges of the axle shaft. The axle shaft runs through the hub and bearing in the spindle.

Jun 16, 2010 | 1999 Daewoo Nubira

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

2 Answers

How to replace rear wheel bearings


don't have topaz. maybe escort will help guide you.

Section 04-02: Suspension and Wheel Hubs, Rear 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Wheel Bearing and Hub Assembly NOTE: Wheel bearings are not serviceable and should therefore be replaced as an assembly with the wheel hub (1104).

Removal
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
  1. Remove the hub grease cap (1131) from the wheel hub.
  1. If equipped with disc brakes, remove the rear disc brake caliper (2552) and rear disc brake rotor (2C026). Refer to Section 06-04 for the removal procedure.
  1. If equipped with drum brakes, remove the two brake drum screws and the brake drum (1126).
  1. Unstake the rear axle wheel hub retainer (4B477) securing the wheel hub to the rear wheel spindle (4A013). Remove and discard the rear axle wheel hub retainer.
  2. Remove the wheel hub from the rear wheel spindle.

Feb 06, 2010 | 1990 Mercury Topaz

1 Answer

Cause of wobble in front end on 1992 ford taurus


what you have described is what happens when the wheel Bearing/Hub Assembly goes bad and needs to be replaced about a $80 part

Dec 10, 2008 | 1996 Ford Taurus

1 Answer

1996 ford bronco


Good lighting will help. Also, use a brake cleaner spray or penetrant to clean things off so you can see .I have a 1996 F150 with push button 4WD with manual locking hubs. Dana 44 axle. Yours may be similar. For front wheel, remove locking ring just inside the inner edge of the hub housing (once you remove the manual hub locking switch, 6 screws on mine, could be 3 on others). Not conspicuous, took me awhile to find. Your hub locking assembly will appear to be recessed just behind its edge goes around outer circumferance. Next, Remove the locking spring (looks like a washer) around the very end of the spline shaft. This is towards the center around the shaft. There is a silver looking retainer ring you have too pull it over, use very small standard screwdriver. Locking mechanism should pull right out after that, giving you access to the outer bearing adjustment nut. Use 4 prong wheel bearing nut socket readily available at auto parts stores. Remove adjustment nut. Next, remove spacer that fits into keyway on shaft. There is nothing holding it on, just pull it off. Beneath that there is another bearing nut, remove this also with 4 prong socket. Just pull hub off after removed. Sometimes rust will keep you from removing at this point. Just get a good penetrant lubricant, spray on and let soak, repaeat if necessary . You can also get a plastic 4lb+ dead blow hammer to assist. Bang on rotor from inside to out. Be prepared to service wheel bearings, they fit into the inside of the rotor/hub assembly and will be dislodged when you remove it. This is as far as I have gotten myself. Good Luck.

Oct 21, 2008 | 1996 Ford Bronco

1 Answer

Wheel bearing


u have to take the hub off. and press the wheel bearing out. it takes alittle time to do bc u have to take your rotor and brake assembly off to get to the hub.

Jun 25, 2008 | 2001 Ford Escape

Not finding what you are looking for?
1996 Ford F250 Crew Cab Logo

4,021 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...