Question about 1998 Chevrolet Cavalier

1 Answer

Same problem I actually tried this prior to receiving your advice and it helped some bbut not completely. Do I need to bleed it and if so, where is the bleed valve? thanks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

The bleed valve is located on the back side of the back plate of the axle. Try bleeding the system.

Posted on Jun 11, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can i bleed my van

Do you need to bleed the brakes? While to procedure is similar, stating the actual vehicle you are working on will result in a more complete answer or a reference video on youtube that will show you how it is done. First thing you need to do is go to an auto parts store and get a bottle of brake fluid and a brake bleeding kit. Always make sure that the reservoir is full as you proceed or you may reintroduce air into the system and have to start over. You will need 2 people to perform this job.

Jul 05, 2015 | Cars & Trucks

1 Answer

Brake and traction control light are on

You need the ABS system control module scanned for fault codes to see what is going on.

Jul 13, 2017 | 1998 Honda Accord

1 Answer

Where can i bleed the fuel system under the hood

This is the simplest way to bleed your fuel system short of trying to explain to you where to find an actual bleed port. Loosen any fuel line under the hood until a constant flow of fuel is coming out then tighten the line. Of course ensure you properly prepare the area for the free flowing fuel prior to opening the line.

Jul 11, 2013 | 2007 Chevrolet Uplander LS Minivan

1 Answer

Audi tt leaking clutch fluid

Replace the hydraulics. This video may help
2000 Audi TT Clutch Replacement

Jun 11, 2017 | Cars & Trucks

1 Answer

No clutch pedal after fitting new clutch pugeout 407

you have an air bubble in the system.. keep bleeding it and it should return. if the clutch master cylinder is like a ford then you actually have to remove it to get the air out by holding the master at the right angel for the air to be completely removed....

Jul 14, 2012 | Peugeot 407 Cars & Trucks

1 Answer

I have a 97 Pontiac Transport and I changed the vacuum booster and master cylindar and lines. blead the system by the book and still cant get breaks unless i pump them. tried everything i can think of.

Did you bleed the master prior to installation? Try opening the bleeder screws and allow the system to gravity bleed then, manual bleed also dont forget to adjust shoes as they can account for low pedal.

Mar 11, 2012 | Cars & Trucks

2 Answers

Peressure bleed a cluch pt 2003

Try a manual bleed first, as it may achieve the same result without the hassle of pressure bleeding.
Fill the master cylinder resevoir, keep it topped up while cracking open the slave delivery line- wait for a steady dribble of fluid to come through - a couple of gentle pumps of the master cylinder will help the process.
Then move to the slave cylinder bleed nipple - crack it open and repeat the process above.
Once you get a bit of pedal pressure back, it's fairly straightforward to complete the bleed process.

Oct 06, 2009 | 2006 Chrysler PT Cruiser

2 Answers


one or two things make sure the float in the resivior is not stuck and the wire is pluged up,or make sure you bleed the master cylinder.and also you may have to bleed the brakes as well.hope this helped

Jan 24, 2009 | 1994 Ford F250 Supercab

1 Answer

How do you depress the brake caliper on 06 s type jaguar

C-clamp, and turn it in slowly to avoid damage to brake parts. Take lid of master cylinder is good idea prior, just to help a little.

Dec 13, 2008 | 2006 Jaguar S-Type

1 Answer


hi from the uk the fact your clutch fluid was low? indicates that you have a leak most probably the slave cylinder ? this is the one at g/box that works clutch or the master cylinder this is the one at pedal ? if either cyl leaks then air also can enter the system so look around each cylinder for leaks? if vehicle is needed then for now you will need to bleed air from the slave cyl bleed nipple i suggest you open bleed nipple 2 or 3 turns then remove cap from reservoir flui will emit from nipple eventually in a constant flow then close nipple and top up res then try pedal by pumping? may improve?? but if not then best advice is if leak is from slave cyl? renew it then bleed as above? ps if leak is actually from master cyl? dripping inside near pedal then change both cylinders it is easy d i y job i am sure you can overcome hope this helps? you can try for parts at local motor stores not necessarilly the dealers? and save $$$$s in garage costs? don't forget a bottle of new fluid? for bleeding

Nov 27, 2008 | 1997 Dodge Dakota

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides