Question about 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger

I have a 2000 ford Ranger and i have a ABS CODE that Come up B1676 any idea

Posted by on

  • Joe T. Olson Dec 20, 2011

    HEY, you should really take this to a certified sevice tech at a good shop. yes it can be caused by a jump start. but what they really mean is at some place and time the anti-lock brake unit saw voltages below 9-8 volts. if you havent had a dead or weak battery this could be the signs of a short in the main harness of your anti-lock system.

  • Anonymous Mar 13, 2014

    abs light is on on my 2000 ford ranger what does that mean

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 883 Answers

TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Posted on Jun 11, 2008

  • sparkola Dec 11, 2010

    So you jump start the truck and the abs stops working and doesnt light the abs lamp but does throw a B1676 code. What do you do then?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced wheel bearing and speed sensor on RF, 2000 f350 diesel dually. Drove 1 month about 1000 miles, now I get c1145 and c1230 with abs light. Any ideas?


ABS code C1145 - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > 1997 - 2003 F150
Aug 20, 2009 - ABS code C1145 1997 - 2003 F150. ... C1220 Yellow ABS WarningIndicator Failure (2) C1222 Wheel Speed ... C1230 Rear ABS Sensor (Electrical/Static) (2) ... ABS light on (Anti Lock Brakes) and I hear pump when in turn ...
Oct 9, 2010
ABS code C1206-2003 F150 SuperCrew
Aug 13, 2007
ABS light C1230
Oct 22, 2006
ABS light on DTC's C1229,C1230
Nov 18, 2002
More results from www.ford-trucks.com

Nov 17, 2015 | Cars & Trucks

2 Answers

2000 ford expedition I changed plugs pcv egr valve cover gasket I am still getting power loss and hesitation in drive and sometimes it stalls plus I have a b1676 code


There is no B1676 DTC. You probably mean P1676 which refers to incompatible injector data. Probable causes are:
1. Control unit software needs updating
2. Faulty PCM or ECM

Checking these two probable causes may get performance back to normal.

Jan 16, 2014 | Cars & Trucks

1 Answer

I have a 2000 ford expedition it is gasping for air it stalls and has a b1676 code


check vacuum leaks such as hydro box linkage host.. the code is ABS lamp and Break Lamp problems

Jan 16, 2014 | Cars & Trucks

2 Answers

2000 ford ranger with 3.0 eng. and stick shift, while driving my speedometer quit at the same time my abs brake warning came on. the speedometer starts working after i getup to about 55 or 60 mph any ideas...


Check ABS tone rings and sensors at wheels. Speedometer may be using these signal too. Visually verify rings (look like gears around axles) are intact with all teeth and sensors are at rings with connector attached. Troubleshooting the ABS system is beyond my skill level. If no joy on visual inspection, maybe one of the other experts can chime in on troubleshooting ABS.

Sep 09, 2010 | 2000 Ford Ranger SuperCab

1 Answer

I have a 2000 Ford Ranger w/ a code 19 flashing on the dash, The bags were blown , have replaced them and the air bag computer still have a code 19 Any ideas?


you will have to replace the Restraint Control Module to clear the error. Until then the airbag should not deploy in a crash. It should be located under the radio.

The part will run in the neighborhood of $100

Oct 22, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Check Engine Light


This totally could be the problem in this video

Jun 18, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Speed sensor diagram for 2000 ford ranger


This video shows the speed sensor and its location for a 2000 ford ranger xlt. It also describes the problems a bad sensor can give.

Nov 06, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

1,778 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...