Question about 1997 Chevrolet Camaro

2 Answers

Turn signal my hazards come on but only flash in the back, fronts go on, no turn signal go on when i hit the switch, the front don't but the back does, i changed the flasher but nothin changed i'm clue less help

Posted by on

  • 4 more comments 
  • Anonymous Jun 22, 2008

    yes

  • Anonymous Jul 04, 2008

    weres the flasher for the turn signals

  • Anonymous Sep 01, 2008

    I have no right or left turn signals in the dash or on outside bulbs. This happened when my son pluged his boat trailer into our four pin jack, tried the signals and nothing. Unpluged the trailer and I still have no signals. We replaced the electronic combination flasher and it did not fix the problem. We have no blown fuses in the engine fuse box. Thank for any help.



    Daryl

  • netmender7 Sep 02, 2008

    On my 2000 Camaro the turnsignal blew while on a road trip after I had been driving for several hours and then it started raining. The housing took on water and subsequently blew the bulb. the dealer repaired this under warantee taking over 3 1/2 hours to replace the pig tails and bulbs, but their fix was short lived and the turnsignal blew again within a month. Not wanting to spend hundreds of dollars for a repair that has little chance of being successful I never repaired it. I've wondered if the heavy duty police Camaros had better electrical components?

  • Anonymous Nov 03, 2008

    how to i change the relay?

  • Anonymous Mar 23, 2009

    I have the same problem , I just put my battery back in my Camaro and i noticed now my hazards don't work . When I lift it up it stays completely lit but it stays on and doesnt blink at all . My turn signals on the front of the car and back of the car and inside the car nothing ? Any IDeas ?

    If anyone can be so kind and email me jokerslye@gmail.com I would appreciate it thanks .

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

I seem to remember that if the 3rd brake light (located in the middle of the rear spoiler) was out that the turn signals would be affected. Sort of a way to notify the driver that it was out. I could be wrong though.

Posted on Jul 30, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 291 Answers

If both front turn signals don't work, there a chance that you have a problem with the relay. It doesn't sound probable that both of the bulbs blow at the same time.

Eitan.

Posted on Jun 11, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

My turn signals sometimes will quit working then I have to hit the hazard lights button leave it on and then turn my turn signals on then they work what causes this to happen


When the turn signals quit working pull up , down , front to back an back to front on the turn signal switch handle . Do they work when doing this ? Pontiac had bad switch . The power for the turn signals goes through the flasher / hazard module . Could be the switch or the module.
The HAZARD LPS fuse in the left hand instrument panel (LH IP) junction block supplies battery positive voltage to the flasher module, which is part of the hazard switch assembly. The TURN LPS fuse in the LH IP junction block supplies ignition positive voltage to the flasher module. The turn signal lamps may only be activated with the ignition switch in the ON position. When the turn signal switch is placed in either the left or right position, current flow is from the flasher module's output to the turn signal switch assembly. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators.

Mar 12, 2016 | 2001 Pontiac Grand Am GT

1 Answer

No turning signals


Turn Signal Lamps
The turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL, CORN LPS Fuse. Battery voltage is then applied through the TURN SIGNAL, CORN LPS fuse circuit to the hazard warning switch. The hazard switch supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the body control module (BCM) . The front turn lamps are grounded at G101. The rear turn lamps are grounded at G301 and G302.
Turn Signal Lamps and/or Indicators Inoperative

2

  1. Turn the ignition switch to the ON position.
  2. Place the turn signal switch in the LH and RH on position.
Do the turn signals operate properly?
Go to Testing for Intermittent Conditions and Poor Connections yes
Go to Step 3 no

3

Are all of the turn signal lamps and indicators inoperative?
Go to Step 5 yes
Go to Step 4 no

4

Are only the turn signal indicators inoperative?
Go to Step 16 yes
Go to Step 9 no

5

Check the TURN SIGNALS CORN LPS fuse for an open.
Is the TURN SIGNALS CORN LPS fuse open?
Go to Step 25 yes
Go to Step 6 no

6

  1. Disconnect the hazard switch.
  2. Turn the ignition to the ON position, with the engine OFF.
  3. Connect a test lamp between the ignition positive 1 voltage circuit of the hazard switch and a good ground.
Does the test lamp illuminate?
Go to Step 7 yes
Go to Step 27 no

7

Connect a test lamp between the ignition 1 positive supply voltage circuit of the hazard switch and the ground circuit of the hazard switch .
Does the test lamp illuminate?
Go to Step 8 yes
Go to Step 23 no

8

  1. Install a fused jumper between the ignition 1 positive voltage circuit of the hazard switch and the turn signal flasher signal circuit of the hazard switch.
  2. Place the turn signal switch in the RH on position and the LH on position.
Do the turn signal lamps illuminate?
Go to Step 17 yes
Go to Step 15 no

9

Is a front turn signal inoperative?
Go to Step 10 yes
Go to Step 13 no

10

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative front turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative front turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14 yes
Go to Step 11 no

11

  1. Disconnect the body control module (BCM) connector.
  2. Connect a test lamp between ground and the front turn signal switch signal circuit of the BCM.
  3. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 12
Go to Step 22

12

Test for an open or for a high resistance in the supply voltage circuit of the inoperative front turn signal lamp. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 21

13

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative rear turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14
Go to Step 28

14

Connect a test lamp between the ground circuit of the inoperative turn signal lamp and supply voltage circuit of the inoperative turn signal lamp.
Does the test lamp illuminate?
Go to Step 20
Go to Step 26

15

Test for an open or high resistance in the turn signal flasher signal circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 18

16

  1. Turn OFF the ignition.
  2. Disconnect the instrument panel cluster (IPC).
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal indicator and the instrument panel cluster (IPC) ground circuit.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 19
Go to Step 24

17

Inspect for poor connections at the harness connector of the hazard switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 30

18

Inspect for poor connections at the turn signal switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 29

19

Inspect for poor connections at the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 31

20

Inspect for poor connections at the inoperative turn signal lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 32

Sep 05, 2015 | 2001 Oldsmobile Intrigue

1 Answer

I just bought the car the turn signals work in the front but not in the back whats the problem?


Have you checked the bulbs already?
Don't know what kind of car you are dealing with here.
Most vehicles - the brake lights and rear turn signals share the same electrical circuit to the rear tailights. Usually the turn signal switch will separate which signal goes to the back.
Do your brake lights work? Is there a High mounted stop lamp and does it work?
I have seen a Hazard Switch be ON and fuse blown causing the Hazard Flasher to be inop - which prevented the turn signals from working. Turning OFF the hazard flasher brought back the T/S.
Check the rest of the lights - see what does and doesn't work - and do the front turn signals flash? Stay On? Or flash really slow?
Let me know what you find out and if this helps you at all.

Mar 12, 2015 | Cars & Trucks

1 Answer

I have a 1991 celica and for some reason the front signals does not work at all. When I turn on the blinkers it blink really fast on both sides but hazard light works fine it blinks normal but it...


check the main earth wire near the battery. and one near the rear of the lights. unbolt them and clean the connectors up put some grease on them after. then check again. remember that when the earth wires come off the radio code will be needed to reset the the radio. be safe and take the battery off.

Sep 28, 2013 | Cars & Trucks

1 Answer

Hazard lights malfunction


YOU MIGHT HAVE A BURNT OUT RELAY IN FUSE COMPART UNDER YOU CARS HOOD CHECK THAT OUT THRU YOUR CARS MANUAL,IT WILL SHOW YOU WHICH RELAY IT IS?

May 24, 2013 | Cars & Trucks

1 Answer

On my 2004 impala, the front right turn signal doesn't work, (only works with hazard lights). And the back right signal is fast. The signal "clicking" sound is non stop but on the other hand...


If the turn signal filament of the right front park/turn lamp is known to be OK and the hazard switch is in the normal position, the hazard switch or the turn signal/multi-function switch could be defective

Oct 16, 2012 | Cars & Trucks

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

I have a 99 Pontiac Sunfire, 2.2L and my turn signals quit working. I replaced the combination switch and the flasher/hazard relay, and still no joy. The problem was intermittent, and now it's just dead....


It will turn on when I hit the button and the turn signals do work. All of this has led to my ABS lights to come on as well. ??????????? Your best bet , take it to a qualified repair shop or learn to do better explanation's ! Or lean to do automotive electrical testing .
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
Electric Testing Techniques You Need to Know

How to Use Multimeter to Troubleshoot Common Problems

Do you know what a wiring diagram is ? How to use a DVOM - digital volt ohm meter ? Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. year make ,model and engine size. Under system click on lighting ,then under subsystem click on turn signals . Click the search button then the blue links .Check power an ground circuits ! This is how we diagnose electrical faults , not just replacing parts .

Turn Lamps
Voltage is applied through the TURN fuse and the turn/hazard flasher when the ignition switch is in the following positions:
• RUN
• BULB TEST
• START
The voltage travels to the contact in the hazard switch. The hazard switch is located in the turn/hazard-headlamp switch assembly. This contact is normally closed.
When the left turn signal is turned on, voltage is applied to the following components.
• The left turn indicator
• The left front park/turn lamp circuit 14
• The left rear turn lamp circuit 18
The turn lamps turn on immediately. The current flow heats up the timing element. The timing element is located in the turn/hazard flasher. The timing element repeatedly opens and closes the circuit. This action causes the turn lamps to begin flashing.
The voltage that is applied to the left front park/turn lamp is also applied to the left front marker lamp. If the headlamp switch is in the OFF position, the left front marker lamp will find a path to ground through one of the following lamps. The following lamps provide low resistance paths to ground:
• The right front marker lamp
• The right turn indicator
• The right front park/turn lamps
• The left front park/turn lamps
The left front marker lamp flashes with the turn lamps. The voltage drop across the marker lamp is much higher than the voltage drop across the other lamps. The lamps that are used for the ground path will not flash.
When the headlamp switch is in either the PARK or HEAD positions, voltage is applied through the following components:
• The EXT LP fuse
• The marker lamps
• The park lamps
When the left turn signal is turned on, the left marker lamp will have voltage at both connections. The left marker lamp does not light. When the turn/hazard flasher stops the voltage to the turn lamps, the marker lamp is grounded through the turn lamp. The marker lamp does not go on. The left front marker lamp flashes in the following manner:
• The left front marker lamp flashes on when the turn filament of the left front park/turn lamp goes off.
• The left front marker lamp flashes off when the turn filament of the left front park/turn lamp goes on.
Voltage is applied to the right lamps in the same manner, when the right turn signal is turned on.
Hazard Lamps
Voltage is applied at all times through the following components to the normally open contact of the hazard switch in the turn/hazard-headlamp switch assembly:
• The STOP HAZ fuse
• The turn/hazard flasher
When the hazard switch is turned on, voltage is applied to the following components:
• The front turn lamps
• The rear turn lamps
The following lamps flash on and off:
• All of the turn lamps
• Both of the turn indicators
The front marker lamps flash with the hazard lamps on, just as the front marker lamps flash when the turn lamps are on. If the headlamp switch is in the OFF position, the front marker lamps flash on when the hazard lamps are on. The front marker lights will flash on when the hazard lamps are on if the headlamp switch is in one of the following positions:
• PARK
• HEAD
When the hazard lamps are on, the following conditions apply:
• The turn circuit is always open.
• The turn/hazard flasher controls the lamp.
Park/Marker Lamps
Voltage is applied through the EXT LP fuse, to the headlamp switch at all times. Voltage is applied to the park lamps and the marker lamps when the headlamp switch is in the following positions:
• PARK
• HEAD
The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
Stop Lamps
Voltage is applied through the STOP HAZ fuse to the brake switch at all times. When the brake pedal is depressed, the brake switch closes. This action applies voltage through the turn/hazard-headlamp switch assembly to the following lamps:
• The high mounted stop lamp assembly
• The left tail/stop-turn lamps
• The right tail/stop-turn lamps


Jun 30, 2017 | 1999 Pontiac Sunfire

1 Answer

Left turn signal does not flash, I have changed


the turn signal switch is probably bad remove cover and check out puts with a test light to make sure

Jun 03, 2009 | 1998 Ford Escort

Not finding what you are looking for?
1997 Chevrolet Camaro Logo

886 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...