Question about 2000 Oldsmobile Alero

1 Answer

Installing blower motor on a 2000 alero

How to remove old blower and install a new one

Posted by on

  • Anonymous Jun 10, 2008

    i dont know where it is.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Expert
  • 611 Answers

Its on the bottom passenger side of the dash on the theres a plastic panel held by clips

Posted on Jun 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The blower on my 2000 Olds Alero isnt working


You would need to know if the blower motor is running. If it is not, you would need to know if it is getting power and ground.
If it is running, it could be a blend door problem under the dash.

Jan 11, 2013 | 2000 Oldsmobile Alero

1 Answer

How do I replace the heating fan on my 2000 Kia sportage


Blower Motor
Removal & Installation
To Remove:


  1. Evacuate and recover air conditioning refrigerant.
  2. Remove battery.
  3. Disconnect and cap A/C lines at evaporator tubes.
  4. Remove blower motor assembly drain.
  5. Remove glove box.
  6. Remove 5 screws and right hand instrument panel lower trim panel.
  7. Remove screw that attaches upper center console to gain access to left
    instrument panel lower support.
  8. Remove left and right bolt and remove instrument panel lower support.
  9. Detach control cable from inlet duct.
  10. Disconnect blower motor electrical connector.
  11. Pull carpet back and remove hole cover plate.
  12. Remove 2 bolts at top of blower motor assembly.
  13. Remove 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  14. Remove blower motor assembly.

To Install:


  1. Install blower motor assembly.
  2. Install 2 bolts at top of blower motor assembly.
  3. Install 2 nuts that attach bottom of blower motor assembly to mounting studs
    on bulkhead.
  4. Install hole cover plate and replace carpet.
  5. Connect blower motor electrical connector.
  6. Install instrument panel lower support and install left and right bolts.
  7. Install right hand instrument panel lower trim panel and 5 screws.
  8. Install glove box.
  9. Install blower motor assembly drain hose.
  10. Connect evaporator lines at bulkhead.
  11. Evacuate and charge air conditioning refrigerant.
  12. Install battery.

Oct 29, 2010 | 2000 Kia Sportage

1 Answer

How to remove and install a new heater blower motor 2000 Saturn


Removal & Installation
  1. Select the following settings:
    Turn the ignition ON Select Recirc in the OFF setting Turn the ignition OFF
  2. Disconnect the negative battery cable.
  3. Remove the wiper arm assemblies.
    CAUTION A sharp edge is revealed once the weatherstrip is removed.
  4. Remove the weatherstrip at rear of the engine compartment.
  5. Remove the cowl retaining nuts.

    7f880eb.jpg

    Fig. Remove the cowl screen assembly

  6. Remove the cowl screen assembly.
  7. Rotate the locking tabs outward to release the filter assembly.
  8. Remove the filter by lifting straight up.

    3f001dc.jpg

    Fig. Remove the wiper module retaining bolts

  9. Remove the wiper module retaining bolts.
  10. Reposition the wiper module to the right.
  11. Remove the filter housing attachment bolts.
  12. Remove the filter housing.
  13. Remove the blower motor housing:
  14. Remove the blower motor housing screws

    855cd3a.jpg

    Fig. Release the locking tabs and remove the fan housing

  15. Release the locking tabs and remove the fan housing
  16. Disconnect the blower motor electrical connector.
  17. Squeeze the bottom of the connector and pull downward.
  18. Remove the blower motor assembly by lifting straight out.
To install:

NOTE The fan motor assembly rib must be located into the channel in the module housing.
  1. Install the blower motor assembly into the module housing.
  2. Connect the blower motor electrical connector.
    NOTE The housing rib must fit into the slot in the HVAC module case.
  3. Install the blower motor housing. Snap the left and right clip into place
  4. Tighten the fan housing to blower motor housing screws to 9 inch lbs.(1 Nm).
    NOTE A new filter housing seal must be used whenever the filter housing is removed to prevent water from leaking into module.
  5. Remove the filter housing seal using a small flat-blade screwdriver.
  6. Install a new filter housing seal.
  7. Install the filter housing.
  8. Install the filter housing screws, and tighten the screws to 31 inch lbs.(3.5 Nm).
  9. Position the wiper module.
  10. Install the wiper module bolts, and tighten the bolts to 44 inch lbs.(5 Nm).
  11. Install the passenger compartment air filter. Notice the air flow direction indicator printed on side of the filter.
  12. Rotate the locking tabs on the filter housing inward to secure the air filter in place.
  13. Install the cowl screen.
  14. Install the cowl screen nuts, and tighten the nuts to 9 inch lbs.(1 Nm).
  15. Close filter access door.
  16. Install the weatherstrip at rear of the engine compartment.
  17. Install the wiper arm assemblies.
  18. Connect the negative battery cable.
  1. Disconnect the blower motor electrical connector.
  2. Remove the lower blower motor cover retaining screws.

    dadd8a2.jpg

    Fig. Remove the lower blower motor cover

  3. Remove the lower blower motor cover.
  4. Remove the blower motor nuts.
    NOTE Cut through the case as straight as possible because the motor cup must be replaced.
  5. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
  6. Remove the blower motor and cup from the lower case by cutting through the case between the circular ribs around the motor with a sharp utility knife.
  7. Release the blower motor retaining tab and remove the motor from the cup.
To install:
  1. Install the blower motor into the motor cup that was cut out of the lower case.

    bc83072.jpg

    Fig. Install the blower motor (1) into the motor cup (2) that was cut out of the lower case

  2. Install the blower motor nuts, and tighten the nuts to 21 inch lbs.(2.4 Nm).
  3. Attach the service ring to the motor cup with the screws included in the kit, and tighten the screws to 15 inch lbs.(1.8 Nm).
  4. Install the blower motor and service ring into the HVAC module using the screws included in the kit. Make certain the blower motor electrical connector is pointing rearward in the vehicle, and tighten the screws to 15 inch lbs.(1.8 Nm).
  5. Install the lower blower motor cover.
  6. Install the lower blower motor cover retaining screws, and tighten the screws to 15 inch lbs.(1.8 Nm).
  7. Connect the blower motor electrical connector.

Hope this helps (remember to rate and comment this).

Oct 04, 2010 | 2000 Saturn Ls 4dr Sedan

2 Answers

I have a 2000 olds alero and first the back


It sounds like an electrical nightmare. The rear defrost and the blower motor are probably not related. The fact that the blower motor only runs on high is because the blower motor resistor is bad. I'm guessing the blower motor is just worn out that's why that quit. As far as the turn signal problem, not a clue there, maybe a bad ground somewhere or you're getting feedback from another circuit. Electrical problems are tough enough when they're right in front you, let trying do solve them via email. You need an electrical wiz for a mechanic.

Jan 04, 2010 | 2000 Oldsmobile Alero

1 Answer

How to replace the blower motor fan assembly in a 2000 GMC Yukon XL K1500 4X4


Blower Motor Removal & Installation Delphi
Blower Motor Replacement (Delphi)

1fb4643.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor insulating cover screws.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.
To Install:

  1. Position the blower motor and turn assembly clockwise until tab locks in place.
  2. Install the blower motor insulating cover.
  3. Connect the electrical connector to the blower motor.
  4. Install the instrument panel sound insulator panel (if equipped).

Visteon

Blower Motor Replacement (Visteon)

878e8d8.gif
To Remove:
  1. Remove the instrument panel sound insulator panel (if equipped).
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the blower motor screws.
  4. Remove the blower motor from the HVAC module.
To Install:
  1. Position the blower motor and install mounting screws.
  2. Connect the electrical connector to the blower motor.
  3. Install the instrument panel sound insulator panel (if equipped).

Oct 02, 2009 | 2000 GMC Yukon XL

1 Answer

2000 Olds Alero. Cooling/Heating fan stopped


The blower is on the right hand side under the dash. You are right in thinking the blower resistor is the problem. The resistor is in the heater box behind the blower. Only 2 bolts hold it in but the back one can be a challenge to remove. The bolt is 5.5 mm.

Check for power and ground with a test light at the resistor connector. You should have power on the colored wires in the various switch positions. The black one is ground.

Aug 10, 2009 | 2000 Oldsmobile Alero

2 Answers

Blower only works on the two highest settings


hi the blower motor is under the right side of the dash
remove the hush pannel
you don't have to remove the blower motor but it does give you more room
disconnect the wiring to the resistor there are two 5.5mm bolts that hold the resistor in
remove the bolts and slide the resistor out
install the new resistor and reassemble
hope this helps

Jul 03, 2009 | 2001 Oldsmobile Alero

1 Answer

How do you replace blower motor on 2000 toyota rav4?


REMOVAL

  1. REMOVE GLOVE COMPARTMENT DOOR
    1. REMOVE BLOWER MOTOR
      1. Disconnect the connector from the blower motor.
      2. Remove the 3 screws and the blower motor.

INSTALLATION
Installation is in the reverse order of removal.

Jun 04, 2009 | 2000 Toyota RAV4

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

Related Topics:

980 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...