a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
TO REMOVE GRILLE FROM BEHIND THE BUMPER COVER RELEASE PLASTIC CLIPS AND DETACH THE GRILLE. IF YOU HAVE FOG LIGHTS DISCONNECT THE ELECTRICAL CONNECTORS FROM THE FOG LIGHTS AND REMOVE THE FOG LAMP MOUNTING SCREWS BEFORE DETACHING THE GRILLE.WHEN YOU INSTALL GRILLE PLACE GRILLE IN POSITION AND SEAT THE CLIPS INTO HOLES IN THE BUMPER COVER. IF YOU HAVE FOG LAMPS INSTALL GRILLE IN POSITION THE INSTALL FOG LAMPS MOUNTING SCREWS BACK IN PLACE TO HOLD GRILLE IN POSITION.
The lamps on my 1999 truck are 1 piece. They look like 2 pieces as they were fit together before they were bonded into 1 piece. The fog light housing that fits behind the bumper is bolted to the metal brackets and the lamps come out and go in as 1 big single piece.
You can change the bulbs the same way as on a headlight. There are slight adjustments for aim.
you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.
The foglamp bulbs can be accessed and removed from underneath the
bumper without tools, although it is a tight fit. Turn the lamp socket
1/4 turn counter-clockwise to remove from the rear of the housing. Note
that the screw in the front of the foglamps is for alignment only and
does not remove the outer lens. The fog lamp housing is attached to the
fascia with two nuts which can be removed with a 10mm socket.
Fog lamps can be added to most Laredo model WJ's that came from
the factory without them. Mopar kits are available that include two fog
lights, wiring harness, and steering column switch. Click HERE for part numbers and other information on these kits.
Fog lamps are installed on the front bumper. The switch is located
to the left of the steering column on the dash panel. The fog lamps are
turned off by the circuit relay when the high beam driving lamps are
turned on. The circuit relay is located on the right front wheelhouse
panel near the blower motor.
Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element See Figure 1
Fig. 1: Exploded view of a fog lamp assembly
Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
Remove the reflector assembly from the lamp body.
Remove the bulb holder from the assembly. Remove the element from the bulb.
DO NOT handle elements with your bare hands, always handle with a
clean cloth. Oil from your hands will cause the element to fail.
Installation is the reverse of removal.
Fog Lamp Switch The fog lamp switch is removed and
installed by simply prying the switch from the instrument panel and
unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT
Position the vehicle on a level surface, facing a wall
approximately 25 feet away. Remove the lamp stone shields and loosen
the adjustment nuts.
Turn the fog lamps ON and adjust as follows:
Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
Install all previously removed items after turning OFF the fog lamps.