Question about Hyundai Motor 1998 Accent

1 Answer

My car refuse to start after below description

Good-day Hyundai expert, I have old Hyundai 1998 model 1.5 accent, and I am an Electrical Engineer by profession, I have got problem on with my car, I put fuel injector cleaner - concentartion - 300ml into 9 litres of petrol unleaded, put new oil 5L with 20ml of stop smoke and 100ml of oil charge on the crankcase oil and when I tried to start my car badly dust smoke came out of my exhuast pipe and stops approximately 20metres and refuse to start again, can you please suggest possible solution or damages that may be occured on my car due to this event.

Posted by on

  • 7 more comments 
  • Zukile Jun 10, 2008

    Thank for your prompt professional response, then what should I do in order to rectify the problem?? please help

  • Zukile Jun 11, 2008

    Engine does not run , ignition keeps on jacking and refuse to start and I have clean up my plugs still the same problem persists, do you think that my engine is damaged? but 20 metres is too small for me on order to associate with the word-damage and what else can i try?

  • Zukile Jun 11, 2008

    Engine does not run , ignition keeps on jacking and refuse to start and I have clean up my plugs still the same problem persists, do you think that my engine is damaged? but 20 metres is too small for me on order to associate with the word-damage and what else can i try?

  • Zukile Jun 11, 2008

    Engine does not run , ignition keeps on jacking and refuse to start and I have clean up my plugs still the same problem persists, do you think that my engine is damaged? but 20 metres is too small for me on order to associate with the word-damage and what else can i try?

  • Zukile Jun 11, 2008

    Engine does not run , ignition keeps on jacking and refuse to start and I have clean up my plugs still the same problem persists, do you think that my engine is damaged? but 20 metres is too small for me on order to associate with the word-damage and what else can i try?

  • Zukile Jun 11, 2008

    Engine does not run , ignition keeps on jacking and refuse to start and I have clean up my plugs still the same problem persists, do you think that my engine is damaged? but 20 metres is too small for me on order to associate with the word-damage and what else can i try?

  • hansjkeller Jun 11, 2008

    WOULD LIKE TO PURCHASE A BLOCK HEATER FOR MY NEW HYUNDAI TUCSON.. 220 VOLT.



    DOES ANYONE KNOW WHO SELLS THIS.????



    THANKS



    Hansjkeller2@att.net

  • Marty marty May 11, 2010

    if 5L actually went into crankcase, then remove all but proper amount of 3.8 US quarts, then save rest for next oil change and re-try the engine...

  • Marty marty May 11, 2010

    if 5L of oil went into crankcase then your problem is an overfill and a hydraulic lock-up of engine....piston needs room below when going down...can't compress oil...really 5L?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Zukile make sure the engine is not overfilled.only takes 4 and a half U.S. quarts with oil change.check dipstick with engine cold.i think you overfilled the engine oil.

Posted on Jun 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 hyundai elantra will not go in reverse...any ideas?


Hyundai Elantra transmission won t go into reverse m ...

www.fixya.com > ... > Cars & Trucks > Hyundai
Hyundai Elantra cars & trucks transmission won t go into reverse m ... Question about 1998 Elantra. 1 Answer · Reverse gear almost dead in 1998 Lantra auto.

99 accent wont go into reverse - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...accent/157948-99-accent-wont-go-into-rev...

Mar 28, 2013 - 3 posts - ‎3 authors
Here is my situation and am hoping I might get somebody who can actually help me with this. I have a 99 hyundai accent automatic with ... 2001 Accent No Reverse
10 posts
Apr 10, 2011
1998 Hyundai Accent Automatic Trans Problem ...
10 posts
Dec 6, 2005
More results from www.hyundai-forums.com

Why is it having trouble moving in reverse?


Jan 05, 2016 | Hyundai Cars & Trucks

1 Answer

How do I arrange my spark plug wires on my Hyundai Getz go 2002


How to change spark plugs hyundai accent 01 - 05 - YouTube

? 3:18
https://www.youtube.com/watch?v=tU2vwisJ7v4
Feb 16, 2012 - Uploaded by PNBNC
I filmed this right after changing my old plugs, I figured it was easy enough to film and some people can profit from it. for a ... Coil, you mean wire lol ... When you go to put the spark plug back in, never start it with the ratchet.

How To Replace Change Install Spark Plugs 2001-06 ...

? 3:17
https://www.youtube.com/watch?v=yVV2KcPDFIo
May 14, 2013 - Uploaded by 1A Auto Parts
... spark plugs. This video is applicable to the 2001, 2002, 2... ...spark plugs. This video is applicable to the 2001, 2002, 2003, 2004, 2005, 2006 Hyundai Elantra 2.0L. ... +queentonks A little know-how can go a long way. We're glad ... When do you think is good to replace my spark plugs wires? My spark ...
2001 Hyundai Accent Firing Order: Engine Mechanical ...www.2carpros.com/.../hyundai-accent-2001-hyundai-accent-firing-orderApr 23, 2009 - Engine Mechanical problem 2001 Hyundai Accent 4 cyl Two Wheel Drive Manual 95000 ... Now I'm trying to figure out how they go back on. How do I find out the Engine Firing Order for my car - Hyundai Accent 2001 1.5L?Which is cylinder 1 - 1.6 Accent - Hyundai Forum: Hyundai ...www.hyundaiperformance.com/.../16837-cylinder-1-1-6-accent.htmlJan 13, 2003 - 3 posts - ‎3 authorsFrom what I read though, the coil pack is configured as 1 4 2 3. I'm assuming the first wire on the coil pack goes to cylinder 1. Can anyone ...

Dec 16, 2015 | Hyundai Cars & Trucks

1 Answer

1998 Hyundai Accent p0300 random multiple misfire


that particular vehicle has a distributor-less ignition system. completely stand alone and electronic. change around the known good coils and see if the misfires on the computer change. see, what the trouble codes say is your numbers 1 thru 4 cylinders are misfiring inadvertently. if you move the coils around, which there are 4..one to 2 cylinders and if its 4 bad coils giving problems then the codes will move around. it could be the crankshaft tone wheel or the PCM as well. take it to a good diagnostic facility like a hyundai facility if you want it fixed right the first time. the hyundai parts are a little more expensive but they are the BEST part for your car, OEM parts are the way to go and the mechanic has probably seen this before and can tell you whats wrong before you leave easily.

Nov 13, 2013 | Hyundai Motor 1998 Accent

1 Answer

My 2002 Hyundai Accent is dying at lights and when the car is at an idle


im thinking maybe a fuel filter sounds like it good luck

Aug 10, 2012 | 2002 Hyundai Accent

2 Answers

Torque settings for a hyundai accent 1500 1998 model torque settings for head , conrods and crank


cylinder head bolt torque

52-55 ft lbs. cold engine
59-63 ft lbs. hot engine

connecting rod cap nut 26-28 ft lbs. SOHC
connecting rod cap nut 23-26 ft lbs. DOHC

main caps 41-44 ft lbs.

Dec 19, 2010 | Hyundai Motor 1998 Accent

1 Answer

With respect I have hyundai accent 1.3 ls from a year 1998, power 62 kW,and have a problem with a motor 's work. It starts well when is cold, but after 5 min his work is intermit, sometimes it can stoped...


You can find a schematic at
www.alldata.com
This is a fee based website and you can print out the info you find there.
Goos luck and I hope this helps!!

Nov 29, 2010 | Hyundai Motor 1998 Accent

1 Answer

My hyundai accent won't start anymore. The battery is good because every electrical components works well but when I turn the key to fire the engine nothing happens. The starter doesn't make any noise or...


I just experienced the issue: clic-clac-nothing. Jumps start: same clic-clac-nothing. I set the 4th gear and moved the car. Just started like day one!
It's good, so far but I don't know why...

Jul 08, 2010 | 1997 Hyundai Accent

3 Answers

High-low beams not working


Check for headlight relay and fuse. Some cars have separate circuits for head light flasher and normal high/low beam. From your description, I would suspect a bad connection to/from relay or relay itself.

Jul 07, 2009 | 2006 Hyundai Accent

1 Answer

How to replace a window cable on hyundai accent


I use to have a Hyundai Pony once, there was no cable there.
But still you need to remove the inside cover etc. to get there.
I became an expert blindfolded and a hyunday hater afterwards.

Apr 14, 2009 | Hyundai Motor 1998 Accent

Not finding what you are looking for?
Hyundai Motor 1998 Accent Logo

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...