Question about 1989 Dodge Raider

1 Answer

'89 Raider 3.0 Water pump

I just replaced a broken timing belt/tensioner. Belt continually walks off the water pump pulley and driver side cam gear. If I loosen the tensioner bolt and turn it over by hand, it will stay where it should. The water pump pulley has quite a bit of play, wondering if this could cause the belt to walk off the gear? If I do replace the water pump, is it really necessary to remove the intake and all that? I don't want to remove any more than I have to.
Thanks much!
Jeff

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 3,433 Answers

Remove the intake? No, the water pump is in front. The water pump play can cause the belt to off track.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have this 89 acura legend 2.7l v6 timing belt removed and the water pump removed, the old pump failed which caused the belt to fail, i have new parts and the pump installed only i dont understand to...


Hi, here is what you need to do. Get all of the timing marks lined up as indicated in the picture below. Put the belt on. Without moving the gears off their marks, make the belt tight across the cam gears and then down the right side to the crank gear. All of the slack must be on the left side to be taken up by the tensioner. Release the tensioner to tighten the belt and then verify the marks are still aligned. If the marks are not aligned, loosen the tensioner just enough to turn the gear that needs to be realigned. After tensioning the belt, rotate the crankshaft clockwise 720 degrees and recheck the timing marks. I have pasted the book procedure below. Please let me know if you still have questions. You must get this right.

jturcotte_2242.gif

jturcotte_2243.gif



jturcotte_2244.gif



jturcotte_2241.gif

  1. If the crankshaft or camshafts have been turned with the timing belt removed, remove the spark plugs and advance the crankshaft about 15 degrees beyond TDC of No. 1 cylinder. Make sure the camshaft sprockets are properly aligned with the marks and return the crankshaft to the TDC mark.
  2. Install the belt in sequence on the crankshaft, the front camshaft, water pump and tensioner pulleys, then the rear camshaft.
  3. To adjust the tension, loosen the tensioner pulley bolt about 1 / 2 turn. The spring will automatically set the proper tension. Torque the bolt to 31 ft. lbs. (43 Nm).
  4. Rotate the crankshaft 6 turns clockwise and check that the timing marks on the crankshaft and camshafts align properly. Adjust the timing belt tension again by rotating the crankshaft to the align the blue mark on the pulley with the pointer. Loosen and retorque the tensioner pulley bolt.
  5. Install the remaining parts in reverse order. Torque the crankshaft pulley bolt to 83 ft. lbs. (115 Nm). When installing the side mount bracket, torque the bolts to 40 ft. lbs. (55 Nm).

Sep 13, 2011 | Acura Legend Cars & Trucks

1 Answer

How to change the water pump on a 2006 equinox ls


  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Loosen the water pump pulley bolts.
  3. Rotate the drive belt tensioner to release the tension on the drive belt.
  4. Remove the drive belt from the right idler pulley.
  5. Carefully release the drive belt tensioner spring tension.
  6. Remove the water pump pulley bolts.
  7. Remove the water pump pulley.
  8. Remove the water pump bolts.
  9. Remove the water pump.
  10. Remove the water pump gasket.
  11. Clean the water pump mating surfaces.

To install:

Fig. Remove the mounting bolts (3) to remove the water pump (1) and gasket (2).
  1. Install the water pump gasket (2).
  2. Install the water pump (1).
  3. Install the water pump bolts (3). Tighten the bolts to 10 Nm (89 inch lbs.).
  4. Install the water pump pulley. Loosely install the pulley bolts.
  5. Insure the drive belt is properly centered on all the pulleys except the right idler puller.
  6. Rotate the drive belt tensioner away from the drive belt.
  7. Install the drive belt to the right idler pulley.
  8. Release the tensioner allowing the drive belt tensioner to come in contact with the drive belt.
  9. Inspect the drive belt to insure the belt is properly centered on all the pulleys.
  10. Tighten the water pump pulley bolts. Tighten the bolts to 25 Nm (18 ft. lbs.).
  11. Fill the cooling system.
  12. Inspect the cooling system for leaks.


10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-0.jpg

10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-1.gif

Aug 21, 2011 | 2006 Chevrolet Equinox

1 Answer

How do i set the timing belt on a 1997 cadillac catera?the betl did not break but how do i make sure the belt did not move a couple of teeth.


Hi, there should be marks on the belt itslf that align with hatch marks on the timing gears. Below are the instructions for installation. From these, you should be able to verify that the belt is in time. There are also some diagrams here: http://www.2carpros.com/diagrams/cadillac/catera/1997


To install:
  1. Install the timing belt.
    1. Start at the crankshaft pulley.
    2. Install the timing belt with a double dash (TDC) mark on the belt aligned with the marks on the oil pump and belt drive gear.
    3. Pinch the belt with special tool J 42069-30 to prevent the splines from jumping.

  2. Route the timing belt through the idler pulley for camshafts 3 & 4 then route the timing belt through the camshaft gears 3 & 4.
    1. Ensure the dash marks on the timing belt align with marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen timing belt idler pulley or move the cam gears slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Tighten the idler pulley locking bolt until snug. The idler pulley bolt will be tightened to specifications after the final adjustments are made.




NOTE Timing belt deflection between the camshaft gears number 4 and the idler pulley for camshafts 3 & 4, must be no more than 0.4 inch (1 CM.).

  1. If necessary, adjust the timing belt deflection by turning the timing bolt idler pulley eccentric, for camshafts 3 & 4, counter-clockwise with the special tool J 42069-40, or equivalent.

  1. Route the timing belt through the timing belt idler pulley for camshafts 1 & 2 then route the timing belt through camshaft gears 1 & 2.
    1. Ensure the dash marks on the timing belt align with the marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen the timing belt idler pulley or move the cam gear slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Apply sufficient tension to the timing belt to prevent it from slipping off the gears by turning the timing belt idler pulley eccentric for camshafts 1 & 2 counter-clockwise with special tool J 42069-40 or equivalent.
    4. Tighten the idler pulley locking bolt until snug. Idler pulley bolt will be tightened to specifications after final adjustments are made.

  2. Route the timing belt through the timing belt tensioner.
  3. Apply initial tension to the timing belt by turning tensioner eccentric counter-clockwise, with a 5 mm hex wrench, until marks are set.
    1. Tighten the belt tensioner-locking nut to 15 ft. lbs. (20 Nm).

  4. Adjust the timing belt.
    1. The timing belt must be properly adjusted or engine damage may occur. Do not continue with the engine assembly procedure until the timing belt is properly adjusted.

  5. Install the timing belt cover. Tighten the timing belt cover bolts to 71 inch lbs. (8 Nm).
  6. Install the power steering pump pulley and bolts. Install the water pump pulley and bolts.
    1. Tighten the power steering pump pulley bolts and the water pump pulley bolts after the serpentine drive belt is installed.

Mar 04, 2011 | 1997 Cadillac Catera

1 Answer

Gearbox chatter on tick over do they suffer from dualmass problems also is there a quick way to change the cambelt


Dual Mass Flywheel, and will also need new clutch Remove the engine coverUsing a [16 mm], rotate the tensioner arm clockwise (about 14° )and remove the belt from the pulley.
Remove the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Remove the upper and lower timing belt covers.

Remove the auto tensioner.
NOTE
Rotate the crankshaft clockwise and align the timing mark to set the No.1 cylinder's piston to TDC (compression stroke).
At this time, the timing marks of the camshaft sprocket and cylinder head cover should coincide with each other.




Unbolt the tensioner to remove the timing belt.
NOTE
If you plan to use the timing belt again, mark the rotation direction on the belt so you reinstall it correctly.

SERVICE MANUAL
Applies to: Santa Fe 2004
GROUP
Engine Mechanical System Timing System



INSTALLATION
Install the idler pulley to water pump boss.
NOTE
Insert and install the idler pulley to the roll pin that is pressed in the water pump boss.


Install the tensioner arm and plain washer to the cylinder block.
Install the tensioner pulley to the tensioner arm.
Install the camshaft sprockets and align the timing marks.

NOTE
When installing the camshaft sprockets, fasten them tightly while holding the hexagonal part of the camshaft.
Before installing the timing belt, if the timing marks of the cam sprocket and the cylinder head cover do not coincide, do not rotate the cam sprocket more than 3 teeth in either direction.
Rotating the sprocket more than 3 teeth may allow the valve and piston to touch each other.
If the cam sprocket is rotated more than 3 teeth unavoidably, rotate the crankshaft counter - clock wise a bit before rotating the cam sprocket.
Install the auto tensioner to the front case.
NOTE
At this time auto tensioner's set pin should be compressed and secured with set pin.




Align the timing marks of each sprocket and install the timing belt in the following order. Crankshaft sprocket--> Idler pulley--> camshaft sprocket (LH side)--> Water pump pulley--> camshaft sprocket (RH side)--> Tensioner pulley.
NOTE
In this step, No. 1 cylinder is in the TDC (Compression stroke).
Be very careful if you use your fingers.



Pull out the set pin of the auto tensioner.



Install the upper and lower timing belt covers.
Install the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
Using the wrench [16mm], rotate the tensioner arm clockwise (about 14°) and install the belt to the pulley.
Install the engine cover.
How to adjust the tension of the timing belt
Rotate the crankshaft 2 turns clockwise and measure the projected length of the auto tensioner at TDC (# 1 Compression stroke) after 5 minutes.
The projected length should be 6-8 mm.
Verify that the timing marks of each sprocket are in their specified position.
NOTE
If the timing marks are not in their specified position, repeat from 6 above.

Dec 28, 2010 | 2004 Hyundai Santa Fe

2 Answers

Need to know how to set the timing gears for a geo storm 1991 1.6litre had to replace timing belt


GM Storm/Spectrum 1985-1993 Repair Guide


Timing Belt - REMOVAL & INSTALLATION

Although timing belts may last for thousands of miles past the recommended replacement interval, they should be replaced every 60,000 miles to prevent trouble or damage should they snap. Timing belts do not usually give an indication that they are worn or aging without removing the cover(s) and inspecting the belt. A worn or damaged belt could give out at any time. In some cases, should a timing belt snap while the engine is running, damage could be done to the valve trains or pistons requiring a partial or full engine disassembly. Also, should the belt go when the vehicle is far from home, a costly tow or even more costly repair job and considerable inconvenience may be suffered.
Timing belts must always be handled carefully and kept completely free of dirt, grease, fluids and lubricants. This includes any accidental contact from spillage, fingerprints, rags, etc.. These same precautions apply to the pulleys and contact surfaces on which the belt rides.The belt must never be crimped, twisted or bent. Never use tools to pry or wedge the belt into place. Such actions will damage the structure of the belt and possibly cause breakage.


Spectrum
(see Figures 1, 2 and 3)
The engine must be removed from the vehicle for this procedure to be performed.
  1. Remove the engine and mount it to an engine stand.
  2. Remove the accessory drive belts.
  3. Remove the engine mounting bracket from the timing cover.
  4. Rotate the crankshaft until the notch on the crankshaft pulley aligns with the 0 degree mark on the timing cover and the No. 4 cylinder is on TDC of the compression stroke.
  5. Remove the starter and install the flywheel holding tool No. J-35271 or equivalent.
  6. Remove the crankshaft bolt, boss and pulley.
  7. Remove the timing cover bolts and the timing cover.
  8. Loosen the tension pulley bolt.
  9. Insert an Allen wrench into the tension pulley hexagonal hole and loosen the timing belt by turning the tension pulley clockwise.
  10. Remove the timing belt.
  11. Remove the head cover.
Inspect the timing belt for signs of cracking, abnormal wear and hardening. Never expose the belt to oil, sunlight or heat. Avoid excessive bending, twisting or stretching.
To install:
  1. Position the Woodruff key in the crankshaft followed by the crankshaft timing gear. Align the groove on the timing gear with the mark on the oil pump.
  2. Align the camshaft timing gear mark with the upper surface of the cylinder head and the dowel pin in its uppermost position.
  3. Place the timing belt arrow in the direction of the engine rotation and install the timing belt, first to the crankshaft pulley, next to the camshaft pulley, then to the water pump pulley and finally to the tension pulley. Tighten the tension pulley bolt.
Once installed, there must be not slack in the timing belt. The belt teeth must be in perfect alignment with the gears.
  1. Turn the crankshaft 2 complete revolutions and realign the crankshaft timing gear groove with the mark on the oil pump.
  2. Loosen the tension pulley bolt and apply tension to the belt using an Allen wrench in the hexagonal pulley hole. Torque the pulley bolt to 37 ft. lbs. (50 Nm) while holding the pulley stationary.
  3. Check the timing belt tension using a belt tension gauge, it should be 40-48 lbs. (18-22 Kg).
  4. Adjust the valve clearances.
  5. To complete the installation, reverse the removal procedures. Torque the crankshaft pulley-to-crankshaft bolt to 108 ft. lbs. (147 Nm).
2befeb0.jpg

Fig. 1: Timing belt routing - SOHC engines

716bbfc.jpg
Fig. 2: Align the crankshaft timing gear keyway with the mark in the oil pump - SOHC engines

2f82d49.jpg
Fig. 3: Check the timing belt tension at the center of the longest point between pulleys - SOHC engines


Storm - SOHC ENGINE
(see Figures 1, 2 and 3)
  1. Disconnect the battery negative cable.
  2. Remove the timing belt cover. If necessary, raise and support the vehicle, then remove the right under cover to access the lower timing cover bolts.
  3. If not done already, rotate the crankshaft so that the No. 4 cylinder is at TDC on its compression stroke by aligning the camshaft pulley timing mark to the 9 o'clock position.
  4. Raise and support the vehicle safely.
  5. Remove the crankshaft pulley center bolt, the 4 crankshaft pulley side bolts and the crankshaft pulley from the vehicle.
  6. Loosen the belt tension pulley bolt, then remove the timing belt from around the tensioner and other pulleys. Remove the timing belt from the vehicle.
To install:
  1. Make sure the crankshaft pulley keyway and groove is aligned with the oil pump timing mark and the camshaft pulley timing mark is in the 9 o'clock position. Install the timing belt around the crankshaft timing pulley, followed by the tensioner pulley, water pump pulley and the camshaft timing pulley.
  2. Tighten the belt tensioner retaining bolt. Make sure that the belt is properly tightened and is aligned evenly around all the pulleys:
    1. Turn the crankshaft 2 complete revolutions and realign the crankshaft timing gear groove with the mark on the oil pump.
    2. Loosen the tension pulley bolt and apply tension to the belt using an Allen wrench in the hexagonal pulley hole. Torque the pulley bolt to 37 ft. lbs. (50 Nm) while holding the pulley stationary.
    3. Check the timing belt tension/deflection using a belt tension gauge. The belt should deflect 0.63-0.79 in. (16-20mm) when 22 lbs. (98 N) of pressure is applied to the center of the longest belt stretch.
  3. Check that the camshaft is still aligned to the 9 o'clock position.
  4. Install the timing belt cover, secure it with the 2 lower mounting bolts, then torque the bolts to 89 in. lbs. (10 Nm).
  5. Install the crankshaft pulley to the crankshaft dampener, secure the center bolt and the 4 side bolts. Torque the center bolt to 87 ft. lbs. (118 Nm) and the 4 side bolts to 17 ft. lbs. (23 Nm).
  6. If removed, install the right side under cover.
  7. Lower the vehicle. Install the 4 upper timing belt cover retaining bolts and tighten to 89 inch lbs. (10 Nm).
  8. Install the right engine mount.
  9. Install the power steering pump drive belt and alternator drive belt. Adjust them to the proper belt tension.
  10. Remove engine support fixture and reconnect the negative battery cable.

For DOCH Engine, can visit autozone.com (free register) for more details.

Hope helped with this (remember rated this help) Good luck.

Nov 05, 2009 | 1991 Geo Storm

1 Answer

How to you install a water pumpon a 3.5 97 dodge


Remove the hood bracket bar, 4bolts, then the fan shroud assembly, then the belts, belt adjuster, and timing covers, line up the cam gears, crank gear to the marks , cam has 1 dot, they line up to timing housing 2 dots, (single dot to middle of the 2 dots), crank has 1 dot to mark on the oil pump housing to your right of crank gear, thats TDC. now remove the timing belt tensioner, 2 bolts, and remove the belt, if the pump has leaked, replace the belt, and tensioner if it is NOT metal Pulley, the fibre one will break down from the antifreeze. its a good idea to replace the water pump housing orings behind it, ac bracket has to come off, as the right cam on engine, this not a retiming iussue with the gear. GOOD LUCK. RDJRP

Aug 17, 2009 | 1997 Dodge Intrepid

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

Timing Belt


I have used the Haynes Repair Manual for the Mercury Villager to change the timing belt on my 1993 Villager, twice. I just finished last night with the latest change. I found the Haynes manual to be very useful. This is just an overview:
1. Jack up the the van and support it on jack stands. Remove the front passenger side wheel and 2 plastic splash sheilds.
2. Remove the two radiator hoses on the passenger side of the engine.
3. Remove the pulley from the water pump (4x 10mm bolts)
4. Remove the tensioner pulley, including the bracket, for the A/C compressor. (3x 12 mm bolts)
This one can be difficult because it requires a torx head to loosen the pulley and it's a very tight fit to get a torx in there. I ended up taking the torx head out of the socket then turning it with a 10mm wrench.
5. Remove all 3 drive belts.
6. Remove the crankshaft pulley. (1-1/16" bolt) You will need a good strap wrench to keep the pulley from turning or an impact to remove this bolt. You may be able to remove the pulley just by bumping it with a mallet, but you may need a gear puller.
7. Remove the timing belt cover, it has an upper and lower half and is held in place by several 8mm screws.
8. You will find that the timing belt pulleys on the both cam shafts and the crank shaft have a white paint mark on one tooth. Make sure the marks on the two cam shaft pulleys are in line with a "bump" mark on the back plate of the belt cover. The bump mark for the front cam is located at about the 2 o'clock position and the one for the rear cam is at about the 10 o'clock position. You will need a mirror and flashlight to see this one.
The crankshaft pulley mark lines up with a notch in the oil pan (I think it's the oil pan where the notch is, but you will see it at near the 6 o'clock postion.
9. My new timing belt was a DAYCO and it came with a good instruction sheet. The new belt has an arrow that should point AWAY from the engine. There are also 3 lines on the new belt that will line up with the lines on the timing belt pulleys.
10. The belt tension should be adjusted so that you get about 0.5" - 0.6" of deflection at the center between the two cam shafts.
Note: I recommend replacing both the tensioning pulley and water pump while you are in there.
A water pump is about $32 and the tensioning pulley is about $35 but it's money well spent.
I did NOT replace the tensioner pulley the last time I changed the timing belt, and that is what failed this time. I could have saved myself a lot of work if I had replaced the pulley the first time.

Hope this helps. I'd still buy the HAYNES manual.

Dec 15, 2008 | 2001 Mercury Villager

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

2 Answers

I need to know the name of a part...


I think that would be the cam belt tensioner pulley.

Jul 25, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...