Question about 1994 Ford F150 Styleside Supercab

1 Answer

Ford Ranger 150 Pick Up Truck

My ABS and Brake Lights are on continually. My mechanic cannot find the problem. It has to do with a code 12, but my fluid levels are okay. Any suggestions as to how to get these lights off. Just had back brakes done and work fine.

Posted by on

  • kayalobo Aug 06, 2008

    1997 Ford F150 Styleside Supercab. My ABS light and brake light is on constantly. My brakes will lock up at slow speeds. The brakes work ok, but is very touchy in traffic. Brake fluid level is good.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

Are your brakes hanging up?
or is your ABS light just stuck on or is messed up

Posted on Jun 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Ford Ranger - My break lights and directional signals are not working. My head and tail lights do work. Any advice on what I should check?


Most common is a bad signal light/multifunction switch failure. The brake lights are wired into the signal light circuit within the switch

Apr 09, 2016 | 2004 Ford Ranger

1 Answer

Abs light stays on and is flashing a i think acode


hi Robert

you can check the ABS fault code as following:

switch ignition on and wait for the abs light to start to flash.
it will flash in long and short flashes, long flash stands for ten, short flash stands for one, there is a short pause in between, and long pause after each code, take a note of the code and Google it
good luck
9ba390f1-ca01-44ac-85b4-4603e1244a3a.jpg

CODE 12 CODE 21

Jan 17, 2014 | 1993 Ford Ranger SuperCab

1 Answer

1995 ford ranger wont come out of park


try disconnecting the rods from the ignition switch shift lever inhibitor.this is basically the mechanism which prevents you from turning the ignition switch to the 'lock' position when the shift lever is not in the 'park' position

Jan 27, 2012 | 1995 Ford Ranger Supercab

1 Answer

2004 ford ranger when brakes applied makes sound like a pump running ABS and BRAKE indicator lights are on.


the sound u hear is the abs pump.for the lights to be on and hear the pump running, there is a problem, take it to shop before brakes fail completely

Dec 14, 2010 | 2004 Ford Ranger

2 Answers

1999 Ford Ranger with 4 wheel ABS. I replaced the brakes on all four wheels and the rear wheel cylinders. The rear brake lines were open individually for a very brief time, and bled conventionally. I would...


The brake pads and shoes are not elec., your abs light is on because your abs computer pick up a bad signal from one of your abs sensor's,, take it to any auto parts or some one like autozone where they can do a code reading and get back us with the code so we can help you diag. your trouble code.

Jun 14, 2010 | 1999 Ford Ranger SuperCab

1 Answer

94 ford ranger blowing fuses when i turn on headlights


I would check the trailer light wiring to make sure it doesnt have any wires that are exposed or touching metal.Odds are that is what is causing the fuse to blow

Apr 23, 2009 | 2004 Ford Ranger

1 Answer

Ford Ranger 150 Pick Up Truck


If you are talking about the back brakelights being on continuously, some Ford products have a sliding plastic brake switch under the pedal which sometimes needs adjustment after a brake job. If you are talking about dash lights, then it sounds like the ABS or proportionate valve is stuck off-center. Some vehicles have to be bleed in a factory recommended sequence which keeps that problem from happening.

Apr 23, 2009 | 1991 Ford Ranger Supercab

3 Answers

Where is the abs control module located on a 02 chevy avalanche ?


THE EBCM IS BAD this is the electronic control module that is on abs pump. you can replace seperate I think it is around 500 for part

Dec 30, 2008 | 2002 Chevrolet Avalanche

1 Answer

2003 Ranger FX-II ABS light on


This isn't hard to do at all really and should be easy to procure the part from the local parts store. There is only one little screw holding it in

102969669

  1. Raise and support vehicle.

  2. NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal. Remove the rear anti-lock brake sensor.
1 Disconnect the rear anti-lock brake sensor electrical connector. 2 Remove the bolt. 3 Remove the rear anti-lock brake sensor.
  1. NOTE: Thoroughly clean the mounting surface. NOTE: Inspect the anti-lock brake sensor O-ring for damage; lightly lubricate the O-ring with axle lubricant. To install, reverse the removal procedure

Nov 05, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
1994 Ford F150 Styleside Supercab Logo

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...